Braun 58077 Assembly instructions

Visit our website at: http://www.harborfreight.com
Email our technical support at: [email protected]
Owner’s Manual & Safety Instructions
Save This Manual Keep this manual for the safety warnings and precautions, assembly,
operating, inspection, maintenance and cleaning procedures. Write the product’s serial number in the
back of the manual near the assembly diagram (or month and year of purchase if product has no number).
Keep this manual and the receipt in a safe and dry place for future reference. 21a
When unpacking, make sure that the product is intact
and undamaged. If any parts are missing or broken,
please call 1-888-866-5797 as soon as possible.
Copyright© 2020 by Harbor Freight Tools®. All rights reserved.
No portion of this manual or any artwork contained herein may be reproduced in
any shape or form without the express written consent of Harbor Freight Tools.
Diagrams within this manual may not be drawn proportionally. Due to continuing
improvements, actual product may differ slightly from the product described herein.
Tools required for assembly an d se rv ic e may n ot b e in cl uded.
Read this material before using this product.
Failure to do so can result in serious injury.
SAVE THIS MANUAL.

Page 2 For technical questions, please call 1-888-866-5797. Item 58077
Specifications
Electrical Rating 120-277 VAC / 50/60 Hz / 50W
IMPORTANT SAFETY INFORMATION
TO PREVENT SERIOUS INJURY AND DEATH FROM ELECTRIC SHOCK: THIS PRODUCT MUST BE
INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION CODE BY A PERSON FAMILIAR
WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED.
Before you begin installing, servicing, or maintenance of this product follow these general precautions.
Read These Instructions Completely and Carefully
1. SAFETY: This fixture must be wired in accordance
with the national electrical code and applicable local
codes and ordinances. Proper grounding is required
to insure personal safety. Carefully observe the
grounding procedure under installation section. All
work should be done by a qualified electrician.
2. RISK OF ELECTRIC SHOCK - Disconnect power at
fuse or circuit breaker before installing or servicing.
3. RICK OF PERSONAL INJURY - Fixture may
be damaged and/or unstable if not installed
properly. Tighten all fixture components
to their recommended torque values.
4. WARNING: Make certain power is OFF before
starting installation or attempting any maintenance.
5. To reduce the risk of death, personal injury, or
property damage from fire, electrical shock,
falling parts, cuts/abrasions, and other hazards
please read all warnings and instructions included
with and on this product prior to installation.
6. Do not mount against flammable surfaces.
7. This product is intended to be used outdoors,
and be subject to the elements; such as
rain and snow and we recommend it to be

8. This LED product must be powered
directly to a switched circuit.
9. Make sure that where this fixture will be
mounted is structurally sound and that it
will support the weight of this fixture.
10. This product should not be used in areas with
limited ventilation or high ambient temperatures.
11. This product is intended to be connected to a properly
installed and grounded UL listed junction box.
WARNING! RISK OF ELECTRICAL SHOCK
1. Verify voltage is 120-277 VAC before installing. 2. All wiring connections should be capped
with UL listed wire connectors.
CAUTION! RISK OF PRODUCT DAMAGE
1. Never connect fixture with power on.
2. Do not mount or support product in a
manner that can cut the outer wire jacket
or damage the wire insulation.
3. Avoid covering LED products with insulation,
foam, or other materials that will prevent
convection or conduction cooling.
4. Never connect an LED product directly to dimmer
packs, occupancy sensors, timing devices, or other
related control devices, unless individual product.
5. LED products are polarity sensitive, ensure
proper polarity before installation.
6. Electrostatic Discharge (ESD) can cause damage to
LED products. Wear personal grounding equipment
during installation and service of the product.
7. Do not touch the individual electronic components,
it may cause ESD (Electronic Discharge),
shorten lamp life or alter performance.

Page 3For technical questions, please call 1-888-866-5797.Item 58077
CAUTION! RISK OF INJURY
1. Wear gloves and safety glasses at all
times when removing fixture from carton,
installing or servicing the product.
2. Avoid direct eye exposure to the
light source while it is on.
3. LED LIGHTS ARE EXTREMELY BRIGHT, UNDER
NO CIRCUMSTANCES SHOULD YOU LOOK
DIRECTLY INTO AN LED LIGHT, THIS MAY
CAUSE IRREPARABLE DAMAGE TO THE EYES.
4. Please dispose of packaging materials
and account for all small parts as these
can be hazardous to small children.
WARNING! RISK OF BURN
1. Allow fixture to cool completely before handling.
2. Do not exceed maximum voltage marked on the label.
3. Keep combustible and other materials that can
burn away from the light, lamp, and lens.
General Warnings
1. Assemble only according to these instructions.
Improper assembly can create hazards.
2. Wear ANSI-approved safety goggles and
heavy-duty work gloves during assembly.
3. Keep assembly area clean and well lit.
4. Keep bystanders out of the area during assembly.
5. Do not assemble when tired or when under the
influence of alcohol, drugs or medication.
6. This product is not a toy. Do not allow
children to play with or near this item.
7. Use as intended only.
8. Inspect before every use; do not use
if parts are loose or damaged.
9. People with pacemakers should consult their
physician(s) before installation. Electromagnetic
fields in close proximity to heart pacemaker could
cause pacemaker interference or pacemaker failure.
10. Maintain product labels and nameplates.
These carry important safety information.
If unreadable or missing, contact
Harbor Freight Tools for a replacement.
SAVE THESE INSTRUCTIONS.

Page 4 For technical questions, please call 1-888-866-5797. Item 58077
Installation Instructions
Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this document
including all text under subheadings therein before set up or use of this product.
DANGER! TO PREVENT SERIOUS INJURY AND DEATH FROM ELECTRIC SHOCK: Disconnect power supply
to circuit at breaker box and mark that breaker clearly to ensure it is not turned on during installation.
1. Determine the mounting location. Position the Light
in the general direction of the desired light coverage.
Verify that installation surface has no hidden
utility lines before drilling or driving screws.
2. Remove the Rear Housing by removing two
Door Screws located on the side of the Light.
Door
Screws
3. Carefully disconnect the Cable from Light
to Rear Housing, then lift the Light off
the side hinge of the Rear Housing.
4. Wire Light to power source, see Wiring
Light to Power Source, page 6.
5. Connect the Rear Housing to the wall.
a. If connecting to a junction box (sold separately):
• Attach junction box to the wall.
• Remove pre-cast locators at the
back of Rear Housing.
• Attach Rear Housing to the junction box using
four screws (sold separately). Tighten securely.
Screws
Junction
Box
Rear
Housing

Page 5For technical questions, please call 1-888-866-5797.Item 58077
b. If connecting directly to the wall:
• Using the Rear Housing as a template,
drill three mounting holes on the wall.
280mm
(11.02")
185mm
(7.28")
Rear Housing
• Connect the Rear Housing to the wall
using three screws (sold separately). Be
sure the screws are appropriate for the
material they are screwing into.
• Tighten screws and seal screw
heads with appropriate waterproofing
sealant (sold separately).
Screws
Rear
Housing
6. Reconnect the Cable and Light to the Rear
Housing. Make sure the cable is fully connected.
7. Before closing the Light door, remove the two
Drain Plugs from the bottom of the Light housing.
Plugs
8. Close the Light door and secure it by reconnecting
the two door Screws removed in Step 2.
Door
Screws
9. Reconnect power and verify the Light illuminates.

Page 6 For technical questions, please call 1-888-866-5797. Item 58077
Wiring Light to Power Source
to dimmable IEC
PLEASE READ THE FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM
IN THIS DOCUMENT AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR DISTRIBUTOR
MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS
QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS QUALIFIED TO REPLACE
ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY
STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND
LICENSED TECHNICIANS, AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY
ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS
THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.
Record Serial Number Here:
Note: If product has no serial number, record month and year of purchase instead.
Note: Some parts are listed and shown for illustration purposes only, and are not available
individually as replacement parts. Specify UPC 193175432117 when ordering parts.

Page 7For technical questions, please call 1-888-866-5797.Item 58077
Parts List and Diagram
Part Description Qty
1 Frame 1
2 Lens 1
3 Reflector 1
4 Screw M3x5 8
5 LED Board 1
6 Door Screw M5x16 2
7 Heat Sink 1
8 Screw M4x10 6
Part Description Qty
9 Bracket Screw M4x16 4
10 Bracket 2
11 LED Driver 1
12 Bubble Level 1
13 Gasket 1
14 Rear Housing 1
15 Photocell 1
16  3
1
2357
10
11 13
14
15
469
812
16

26541 Agoura Road • Calabasas, CA 91302 • 1-888-866-5797
Limited 90 Day Warranty
Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards,
and warrants to the original purchaser that this product is free from defects in materials and workmanship for the
period of 90 days from the date of purchase. This warranty does not apply to damage due directly or indirectly,
to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities, criminal activity, improper
installation, normal wear and tear, or to lack of maintenance. We shall in no event be liable for death, injuries
to persons or property, or for incidental, contingent, special or consequential damages arising from the use of
our product. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the
above limitation of exclusion may not apply to you. THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER
WARRANTIES, EXPRESS OR IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS.
To take advantage of this warranty, the product or part must be returned to us with transportation charges
prepaid. Proof of purchase date and an explanation of the complaint must accompany the merchandise.
If our inspection verifies the defect, we will either repair or replace the product at our election or we may
elect to refund the purchase price if we cannot readily and quickly provide you with a replacement. We will
return repaired products at our expense, but if we determine there is no defect, or that the defect resulted
from causes not within the scope of our warranty, then you must bear the cost of returning the product.
This warranty gives you specific legal rights and you may also have other rights which vary from state to state.