BRAYER BR1035 User manual

Instruction manual
Инструкция по эксплуатации
Electric kettle BR1035
Электрический чайник BR1035
brayer.ru

СОДЕРЖАНИЕ
EN......................................................................................................................................3
DE....................................................................................................................................11
RU ...................................................................................................................................20
KZ....................................................................................................................................29

3EN
ELECTRIC KETTLE BR1035
The liquid heating appliance (kettle) is intended for
heating and boiling drinking water only.
1. Kettle ask
2. Control panel
3. Spout
4. Lid
5. Lid opening button
6. Handle
7. Kettle stand
8. Power cord storage
9. Inner water level scale
10. On/O󰀨 button « »
11. Temperature selection buttons «+, -»
12. Water boiling mode indicator
13. Water temperature digital symbols
14. Water temperature maintenance mode indicator
15. Water temperature maintenance mode button « »
ATTENTION!
For additional protection it is reasonable to install a
residual current device (RCD) with nominal operation
current not exceeding 30 mA into the mains. To install
RCD, contact a specialist.
EN
7
2
10 15
1412
11
13
6
1
3
4 5
8
1.5L
MAX
1.0L
0.5L
MIN
9

4EN
SAFETY MEASURES AND OPERATION RECOMMENDATIONS
Read the operation instructions carefully before using the unit, after reading keep it for future reference.
• Use the electric kettle for its intended purpose only, as
it is stated in this manual.
• Mishandling the kettle can lead to its breakage and
cause harm to the user or damage to his/her property
and it is not covered by warranty.
• The kettle is intended for heating and boiling drinking
water only, do not heat or boil any other liquids.
• Make sure that operating voltage of the electric kettle
indicated on the label corresponds to your home
mains voltage.
• The kettle should be always grounded. In case of short
circuit, grounding reduces the risk of electric shock.
• The power cord is equipped with a «europlug»; plug
it only into the mains socket with reliable grounding
contact.
• Contact an electrical technician, if you are not sure
that your sockets are installed properly and grounded.
• To prevent re do not use adapters designed to plug
the power cord into an electrical outlet having no
grounding contact.
• If there is sparking or a burning smell, unplug the
power cord from the electrical outlet and contact your
household electrical service provider.
• If there is smoke from the ask or body of the kettle,
unplug the power cord from the electrical outlet, do
not open the lid of the kettle and take measures to
prevent the re spread. Contact the service center for
inspection or repair of the kettle.
• Do not use the electric kettle outdoors.
• It is recommended not to use the unit during lightning
storms.
• Do not place any foreign objects on the kettle.
• Protect the unit from blows, drops, vibrations and
other mechanical stress.
• Never leave the plugged-in electric kettle unattended.
• Do not use the kettle near a kitchen sink, in bathrooms,
near swimming pools or other containers lled with
water. If the appliance has been dropped into water,
immediately unplug the power cord from the electrical
outlet before removing the appliance from the water.
Contact the service center for inspection or repair of
the kettle.
• If the unit is dropped into water, unplug it immediately,
and only then you can take the unit out of water.
• Do not use the electric kettle near heating appliances,
heat sources or open ame.
• Do not use the electric kettle in places where aerosols
are used or sprayed, and in proximity to inammable
liquids.
• Place the electric kettle on a at stable surface; do not
place it on the edge of a table. Do not let the power
cord hang from the table and make sure it does not

5EN
touch hot surfaces and sharp edges of furniture.
• Do not direct the kettle spout at wooden furniture,
books and objects which can be damaged by moisture
or hot steam.
• Do not touch the power cord and power plug with wet
hands.
• Do not switch the kettle on without water, after the
kettle is lled, close the lid tightly.
• Ensure that water level in the kettle is not above the
maximal mark «MAX», which is situated inside the
kettle ask. If the water level exceeds the maximal
mark, boiling water can splash out of the kettle during
boiling.
• To avoid burns by hot steam, do not bend over the
kettle spout.
• Do not open the kettle lid while water boiling.
• The surface of the kettle may have rather high
temperature. Be cautious and careful when in contact
with heated surfaces of the kettle. Take the kettle by
the handle.
• Be careful while carrying the kettle lled with boiling
water. Be careful when you pour water out of the
kettle, do not tilt the kettle sharply, in case of careless
use of the kettle, you can get burns by hot water.
• Unplug the kettle from the mains before cleaning or
when not in use. When disconnecting the kettle stand
from the mains, hold only the power cord plug and
carefully remove it from the electrical outlet, do not pull
on the power cord as this may damage the power cord
ATTENTION!
Do not allow children to play with polyethylene bags or
packaging lm. Danger of su󰀨ocation!
• The electric kettle is not intended for usage by
children.
• Do not leave children unattended to prevent using the
unit as a toy.
• Do not allow children to touch the unit and the power
cord during the electric kettle operation.
• Place the unit out of reach of children during the
operation and cooling down.
• This appliance is not intended for use by persons
(including children) with reduced physical, mental,
sensory or mental capabilities, or lack of experience or
knowledge, unless they have been given supervision
or instruction regarding the use of the appliance by a
person responsible for their safety.
• Periodically check the integrity of the power cord, the
power plug and the kettle body.
• If the power cord is damaged, it should be replaced
or socket and cause a short circuit.
• To avoid electric shock do not immerse the electric
kettle into water or any other liquids.
• Do not wash the electric kettle in a dishwashing
machine.
• For children safety reasons do not leave polyethylene
bags, used as a packaging, unattended.

6EN
by the manufacturer, a maintenance service or similar
qualied personnel to avoid danger.
• Do not repair the unit by yourself. Do not disassemble
the unit by yourself, if any malfunction is detected, and
after it was dropped, unplug the unit and apply to the
service center.
• Transport the kettle in the original package.
• Keep the unit out of reach of children and disabled
persons.
THE UNIT IS INTENDED FOR HOUSEHOLD USE
ONLY, DO NOT USE THE UNIT FOR COMMERCIAL
OR LABORATORY PURPOSES.
BEFORE USING THE KETTLE
After unit transportation or storage at low temperature,
it is necessary to keep it for at least three hours at
room temperature.
• Unpack the kettle and remove all packing materials and
advertising stickers.
• Keep the original package.
• Read the safety measures and operating
recommendations.
• Check the delivery set.
• Examine the kettle for damages, in case of damage do
not plug it into the mains.
• Make sure that the specications of power supply
voltage specied on the lower panel of the unit or the
base correspond to the specications of your mains.
When using the kettle in the mains with 60 Hz frequency,
the unit does not need any additional settings.
• Wipe the outer and inner surface of the ask (1) with a
slightly damp cloth then wipe dry. Do not use abrasives
and coarse scourers for this purpose.
• Place the base (7) on a solid steady at and non-slip non-
metal surface away from heat sources as far as possible
from the edge of the surface.
• Do not place and do not use the kettle in closed space,
for example, in the cupboard or in closed structures —
this can lead to its breakage, cause harm to the user or
damage to his/her property.
• Wipe the outer surface of the ask (1) with a slightly
damp cloth and then wipe it dry. Do not use abrasives and
coarse scourers for this.
• Before connecting the kettle, make sure that there are no
moisture drops on the base (7), the ask (1), the power
cord and the power plug.
• Press the button (5) to open the cover (4).
• Fill the kettle with water up to the «MAX» mark, according
to the scale (9) located on the inner surface of the ask (1).
• Close the lid (4) and make sure that the lid (4) is tightly
closed.
Note: it is recommended to install the tea infuser (7) in the lid
(9) during the rst boiling of water.
• Place the kettle on the base (4).
• Insert the power cord plug into the mains socket, you will
hear a sound signal.

7EN
STANDBY MODE.
• Plug the power cord into an electrical outlet, then 2 beeps
will sound and the temperature of the water in the ask
(1) of the kettle will be displayed in digital symbols (13).
• Press the On/O󰀨 button (10) « », then a beep signal
will sound, and the water heating temperature will
be shown in displayed symbols (13). When the water
temperature reaches 100°C, beeps will sound, the water
boiling indicator (12) and the heating indicator will light
up, and the kettle heating element will turn o󰀨.
• Press the button (5) to open the cover (4).
• Remove the kettle from the base (7) and carefully pour
out boiled water into a suitable bowl.
• Remember that there is boiling water inside the kettle
ask (1), always hold the kettle only by the handle (6),
do not tilt the kettle sharply, in case of careless use of the
kettle you can get burns by hot water.
• Repeat the water boiling procedure several times.
ATTENTION! To avoid burns by hot steam, do not bend
over the spout (3).
• Hot water resulting from the rst boilings is not recommended
to consume, you may use it for domestic needs.
USING THE ELECTRIC KETTLE
• Place the kettle on a solid steady at and non-slip non-
metal surface away from heat sources as far as possible
from the edge of the surface.
WATER BOILING
• Take the handle (10), pull it upwards and remove the lid (9).
• Fill the kettle with water not lower than the «MIN» mark
and not higher than the «MAX» mark on the scale (9)
located on the inner surface of the ask (1).
• Close the lid (4) and place the kettle lled with water on
the kettle stand (7).
Note: always make sure that water drops do not fall on the
contact unit of the kettle stand (7).
• Plug the power cord into an electrical outlet, then 2 beeps
will sound and the temperature of the water in the ask
(1) of the kettle will be displayed in digital symbols (13).
• Press the On/O󰀨 button (10) « », then a beep will
sound, and the water heating temperature will be shown
in displayed symbols (13). When the water temperature
reaches 100°C, beeps will sound, the water boiling
indicator (12) and the heating indicator will light up, and
the kettle heating element will turn o󰀨.When the water
starts boiling, you will hear sound signals, the button
«100°С» illumination will glow blue, the «ON/OFF» button
(3) illumination will glow green.
• If it is necessary to switch the kettle o󰀨, press the On/O󰀨
button (10) «ON/OFF».
Notes:
- after water boiling, droplets may appear on the surface
of the stand (7) due to steam condensation. This is a
normal phenomenon and is not a warranty case;
- The digital symbols (13) showing temperature of the

8EN
water in the ask (1) of the kettle will go out after 20
minutes.
HEATING THE WATER UP TO PRESET
TEMPERATURE
• You can warm up water up to the required temperature.
For making di󰀨erent tea varieties the special water
temperature is required.
• Recommended water temperature: 40-60°C – for baby
food and other needs, 70°C – white and green tea, 80°C –
instant co󰀨ee, 90-100°C – black tea.
• Press one of the buttons (11) «+ or –» to select the
temperature «40-50-60-70-80-90-100°C», press the On/O󰀨
button (10) « ». At the same time, the heating element will
turn on and the water will be heated to the set temperature.
Notes: the water heating mode is not active when the
temperature is set to 100°C and is used only for boiling of water.
• When the set temperature is reached, beeps will sound,
the water boiling indicator (12) will light up and the
kettle's heating element will turn o󰀨.
• If you want to turn o󰀨 the water heating mode, press the
On/O󰀨 button (10) « ».
WATER TEMPERATURE MAINTENANCE MODE
Notes:
- the function allows to maintain the preset water
temperature within 2 hours without reboiling. At
the end of this time keep warm mode switches o󰀨
automatically.
- operating mode of warm keeping is periodical, if
the water temperature in the kettle ask cools down
by 5 degrees, the boiling mode will switch on, and
after boiling the water will cool down to the preset
temperature.
- 100°C water temperature maintenance mode is not
active
• Press one of the buttons (11) «+ or –» to select the set
the water maintenance temperature «40-50-60-70-80-90-
100°C».
• Then press the button (15) « » to turn on the water
temperature maintenance mode, while the water
boiling mode indicator (12) and the water temperature
maintenance mode indicator (14) will light up.
• The heating element of the kettle will turn on, the digital
symbols (13) will show the temperature of the water in the
ask (1) of the kettle.
• When the water temperature reaches the set temperature,
beeps will sound, the water boiling indicator (12) will go
out, the kettle heating element will turn o󰀨 and the water
temperature maintenance mode will turn on.
Notes:
-if the temperature of the water in the ask (1) of the
kettle is higher than that set in the water temperature
maintenance mode, beeps will sound and the water
temperature maintenance mode indicator (14) will ash;
- after the water has cooled down to the set temperature,
the water temperature maintenance mode indicator

9EN
(14) will stop ashing and will be on constantly, and
the digital symbols (13) will show the temperature of
the water in the ask (1) of the kettle.
• If it is necessary to switch the heating function o󰀨, press
the keep warm mode (15) « » On/O󰀨 button.
Note: if you remove the kettle from the base for the time
less than 1 minute, the keep warm mode will stay on.
• If you accidentally switched the kettle on, but the water
level appeared to be below the minimal mark, the
automatic thermal switch will be on and the kettle will
switch o󰀨. In this case take the kettle from the base (7)
and let it cool down for 10-15 minutes, then ll the kettle
with water and switch it on, the electric kettle will operate
in normal mode.
CLEANING AND MAINTENANCE
• Before cleaning disconnect the kettle from the mains,
pour out water and let the kettle cool down.
• Wipe the base (4) and the outer surface of the ask (5)
with a slightly damp cloth, and then wipe the base (4)
and the ask (5) dry. Use soft detergents to remove dirt;
do not use metal sponges and abrasive detergents and
solvents.
• Do not immerse the kettle, the kettle stand (7), power
cord and power cord plug in water or any other liquid, do
not wash the kettle in the dishwasher.
DESCALING
• Scale, appearing inside the ask (1), inuences the water
taste and disturbs the heat exchange between water and
the heating element and also creates a risk of failure of
the heating element, the burnout of the heating element
because of large amount of scale in the ask (1) is not
covered by warranty.
• To remove scale, you can use special scale-removing
agents, as well as household ones, for example, vinegar
or citric acid.
• Dissolve 25 g of citric acid in 500 ml of hot water, add
water up to the maximum volume of water in the kettle.
• Pour the resulting solution into the kettle and leave for it
15-30 minutes. If necessary, you can turn on the water
boiling mode.
• Pour out the liquid and rinse the ask (5) several times,
boil water several times.
• You can use special detergents for electric kettles or
co󰀨ee machines to remove scale, strictly following the
instructions on their usage which should be placed on
the packing of the detergent or in supplemental materials
provided by the seller.
• Clean the kettle from scale regularly.
STORAGE
• Before taking the kettle away for long storage, unplug it,
pour out water and let the unit cool down.
• Clean the base (4) and the ask (5).

10 EN
• Fix the power cord at the power cord storage (8) on the
kettle stand (7).
• Keep the kettle in a dry cool place out of reach of children
and disabled persons.
DELIVERY SET
1. Electric kettle — 1 pc.
2. Base — 1 pc.
3. Manual — 1 pc.
TECHNICAL SPECIFICATIONS
• Supply voltage: 220-240 V, ~ 50/60 Hz
• Rated input power: 2200 W
• Maximum water capacity: 1.5 L
RECYCLING
To prevent possible damage to the environment
or harm to the health of people by uncontrolled
waste disposal, after service life expiration of
the unit or the batteries (if included), do not
discard them with usual household waste,
deliver the unit and the batteries to specialized
centers for further recycling.
The waste generated during the disposal of the unit is
subject to mandatory collection and consequent disposal in
the prescribed manner.
For further information about recycling of this product
apply to a local municipal administration, a disposal
service or to the shop where you purchased this
product.
The manufacturer reserves the right to change the
appearance, design and specications not a󰀨ecting
general operation principles of the unit, without prior
notice.
The unit operating life is 3 years
The manufacturing date is specied in the serial
number.
In case of any malfunctions promptly apply to
the authorized service center.In case of any
malfunctions promptly apply to the authorized
service center.