Breeze CPD 160 User manual

We bring better air to life
2020
USER’S MANUAL
FULL ABS CEILING FAN
Thank you for choosing full ABS ceiling mounted fan. Please read
and save this user's manual for future reference. Read carefully
before attempting to assemble, install, operate or maintain the
product described. Protect yourself and others by observing all
safety information. Failure to comply with instructions could result
in personal injury and property damage.
CPD 160
CPD 210
CPD 330
CPD Series

www.breeze.com.vn | [email protected]
We bring better air to life
USER’S MANUAL
CPD SERIES
01
1. GENERAL SAFETY INFORMATION
Ÿ Please read the user’s manual carefully prior to installing and operating the unit.
Ÿ This user’s manual is the primary operating document intended for technical, maintenance and operations staff.
Ÿ All user’s manual requirements as well as the provisions of all the applicable local and national construction, electrical and
technical norms and standards must be observed when installing and operating the unit.
Ÿ The warnings contained in the user’s manual must be considered most seriously since they contain vital personal safety
information.
Ÿ Failure to follow the rules and safety precautions noted in this user’s manual may result in an injury or unit damage.
After a careful reading of the manual, keep it for the entire service life of the unit.
Ÿ While transferring the unit control, the user’s manual must be turned over to the receiving operator.
Disconnect the unit from power mains prior to any
installation operations.
While installing the unit, follow the safety
regulations specific to the use of electric tools.
Do not lay the power cable of the unit in close
proximity to heating equipment.
Do not change the power cable length at your
own discretion. Do not bend the power cable.
Avoid damaging the power cable. Do not put any
foreign objects on the power cable.
Do not use damaged equipment or cables when
connecting the unit to power mains.
Do not operate the unit outside the temperature
range stated in the user’s manual. Do not operate
the unit in aggressive or explosive environments.
Do not touch the unit controls with wet hands. Do
not carry out the installation and maintenance
operations with wet hands.
Do not wash the unit with water. Protect the
electric parts of the unit against ingress of water.
Disconnect the unit from power mains prior to any
technical maintenance.
Do not store any explosive or highly flammable
substances in close proximity to the unit.
When the unit generates unusual sounds, odour
or emits smoke, disconnect it from power supply
and contact the Seller.
Do not direct the air flow produced by the unit
towards open flame or ignition sources.
Do not block the air duct when the unit is
switched on.
In case of continuous operation of the unit,
periodically check the security of mounting.
The product must be disposed separately at the end of its service life. Do not dispose the unit
as unsorted municipal waste.
Do not allow children to operate the unit.
The unit must be grounded!
Do not open the unit during operation.
Unpack the unit with care.
Multiple bend
Pipe diameter shrinks
at connecting part
< 0.8m
Adapter
Duct
Outlet closed to crook
UNIT INSTALLATION AND OPERATION SAFETY PRECAUTIONS
ŸBefore installing this product, ensure that the
voltage and frequency consistent with the
product nameplate.
ŸWhen connected to power supply, all-pole
power switch with more than 3mm contact
separation is necessary to be installed on the
power supply circuit. Please do the connection
according to the local electrical equipment
technical regulations.
ŸPlease set up vent and spot inspection.
ŸInstallation height should be more than 2.3m.
ŸShould be firmly installed. Gradient installation
forbidden.
ŸDo not disassemble the junction box by
yourself, if the power cord is damaged, it
should repair by qualified serviceman
ŸInstallation on window or outdoor is forbidden.
ŸPlaces with overmuch lampblack or steam
forbidden.
ŸBelow connection way of air duct is forbidden.

www.breeze.com.vn | [email protected]
We bring better air to life
USER’S MANUAL
CPD SERIES
2. PRODUCTS OVERVIEW
The CPD series is a range of ceiling exhaust fan designed for use as ducted and unducted ceiling mounted extractions.
Material:
• Casing and louver: Injection moulded by ABS polymer.
• Impeller: ABS polymer and high efficiency forward curve centrifugal impeller driven with sealed for by long life bearing.
• Motor: 100% copper coil and fitted with high quality ball bearing, high efficiency, low noise, maintenance free and long service
life. Equipped with thermal overload protection.
• Standard motor range is protected to IP 44, class B insulation.
Feature:
• Be able to speed controllable.
• Low noise levels, including valve one-way
Application: Shopping malls, entertainment and residential area, bathroom, bedroom, office, living room, store, toilets, hotels and
exhaust ventilation.
Construction.
The full ABS ceiling mounted fan consists of the following main parts:
6. Louver
7. Terminal Electric Box
8. Outlet Duct
9. Valve One-Way
10. Screws
Full ABS ceiling mounted fan with standard
motor are suitable for ventilation of:
• Clean air
• Slightly dusty and greasy air
• Slightly aggressive gases and vapour
• Mediums up to an atmospheric density of 1.2 kg/m3
• Mediums with a temperature of -20°C up to +40°C
• Mediums up to a max. Humidity of 85%
• The ambient temperature of the motor must be between -20°C and +40°C make sure and adhere to the specifications of the
motor manufacturer.
3. PERFORMANCE CURVE
4. PERFORMANCE PARAMETERS
Voltage
(V/P/Hz)
220/1/50
220/1/50
220/1/50
Power
(W)
22
30
36
Speed
(rpm/min)
1020
1020
750
Noise
dBA
(at 3m)
32
34
36
Max.
Air Volume
3
(m /h)
160
210
330
Model
CPD 160
CPD 210
CPD 330
210x210
240X240
270X270
Installation
(mm)
Weight
(Kg)
1.8
2.0
2.8
Max.
Pressure
(Pa)
120
150
150
60
30
90
120
30 60 90 120 150 180
CPD 160
Pa
3
m /h
150
0
60
30
90
120
50 100 150 200 250
CPD 210
Pa
3
m /h
150
0
60
30
90
120
50 100 150 200 250 300
CPD 330
Pa
3
m /h
150
0
350
02
1. Full ABS Casing
2. Motor Frame
3. Ball Bearing Motor
4. Forward Curve Impeller
5. Inlet Orifice

03
5. DIMENSION INFORMATION
Electric Connection
6. ELECTRIC INSTALLATION
Wiring Diagram
www.breeze.com.vn | [email protected]
We bring better air to life
AC
Motor
Black
Red
Brown
Capacity
Yellow
Green
Terminals
Yellow Green
Brown
Blue
N
L
FU
Fan
L1
2
3
4
N
L
N
MCB
PE
AC ~
220-240V
50 Hz
PE
• The fan is designed for 220-240V/50Hz (single-phase).
• The fan shall be connected to power supply by means of insulated, durable and thermal-resistant cords (cables, wires).
• Electric wiring must be in accordance with technical connection regulations and local ordinances and national electric codes as
per enclosed wiring diagram in the terminal box or on the casing.
• The recommended wire cross section is minimum 0.75 mm2.
• The actual conductor cross-section selection must be based on its type, maximum permissible heating, insulation, length and
installation method (in the air, pipes or inside walls). Connect the cables to the terminal block incorporated inside the terminal
box located on the fan casing in compliance with the fan wiring diagram and the terminal designation. The terminal designations
are shown on the sticker inside the fan casing.
• Check that supply is according to data on nameplate.
• Insert cable according to the instructions in the junction box and seal it (Avoid water enter).The equipment connected ground
for motor protection according to the instructions - Unless the guarantee isn’t accepted. Connect electric supply.
• After connecting the wiring, install the terminal cover with screws.
7. INSTALLATION METHOD
All dimensions in mm.
Model
CPD 160
CPD 210
CPD 330
A
245
270
300
B
205
235
265
C
180
180
210
D
100
100
150
E
275
300
330
C
B
D
E
A
USER’S MANUAL
CPD SERIES
Fig 2.
Ceiling joist Wooden frame
Enhance piece
Fig 1.
• Make a wooden frame and fix it on to the ceiling as picture reference.
• Install and enclose the fan casing in the wooden frame, and then fix it up firmly with 04 self-tapping screws.
• Connect the pipeline with the main part, and make it well-sealed with the self-adhesive tape (bandage). (Fix the ventilating
pipeline onto the ceiling, keeping the ventilating pipeline straight, without burden on the main part) no burden on the pipeline.
• After connecting the power supply, turn on the switch, check whether there is abnormal condition, and then place spring in the
slot hole to fix the panel.
• We must prevent the gas from the open airway or other firing equipment from back flowing into the room.

www.breeze.com.vn | [email protected]
We bring better air to life
USER’S MANUAL
CPD SERIES
• The equipment type and arrangement should be verified as ordered at once when it arrives at the jobsite. When a discrepancy
is found, the local Breeze Sales Representative must be notified immediately so that corrective action may be investigated,
also verify electrical conformance to specifications. Unauthorized alterations and unauthorized backcharges will not be
recognized by Breeze Fan.
• After the unit has been assembled, installed and all utilities have been hooked up, the unit is now ready for operation.
Check
Before starting the unit, check the following:
• Confirm that building supply voltage matches the voltage for which the unit is wired.
• Check all piping and wiring penetrations
• Made by contractors for water tightness. All penetrations must be made watertight to prevent water damage to the unit and
building.
• Rotate the fan impeller manually to be sure that it is free to operate. Remove any dirt or debris that may have accumulated
during installation.
• Inspect all fasteners to ensure that none have loosened during shipment.
• Check all electrical connections for proper attachment.
• Check casing and ductwork, if accessible, for obstructions and foreign material that may damage the fan impeller.
Checks prior to initial start-up
Proceed with the fan's initial start-up in the following sequence:
• Check that the mechanical assembly has been carried out properly
• Remove foreign bodies located in the suction and outflow areas and in the fan space
• Check that the electrical installation has been completed in accordance with regulations
• Does the mains voltage match the motor voltage specified on the rating plate?
• Is the motor protection system set correctly with regard to the motor's nominal current? The setting must be carried out in
accordance with the corresponding details contained on the motor output plate.
• Has the motor been connected correctly in accordance with the wiring diagram? The connection schematic supplied by the
motor suppliers applies for the connection of the motor.
Starting up the fan for the first time.
Only put the fan into operation after it has been assembled in accordance with the regulations:
• Put the fan into operation.
• Monitor its correct function (quiet running, vibration, imbalance, power consumption, controllability)
Once the unit has been put into operation, a routine maintenance schedule should be set up to accomplish the following:
• Lubrication of bearings and motor.
• Impeller, casing, bolts and set screws on the entire fan should be checked for tightness.
• Any dirt accumulation on the impeller or in the casing should be removed to prevent unbalance and possible damage.
• Inspect fan impeller and casing looking for fatigue, corrosion or wear.
Checks after initial start-up
Check the mechanical connections after initial start-up, especially the joints at the fan.
8. OPERATION INSTRUCTION
Visual Inspection of Equipment
Fig 3.
Self-adhesive tape
Outlet duct
Spring
Louver
Fig 4.
Slot hole
Wall
Louver
Duct Outlet
Fan
Constructor
Fig 5.
04

www.breeze.com.vn | [email protected]
We bring better air to life
USER’S MANUAL
CPD SERIES
9. ROUTINE MAINTENANCE
• Regular maintenance is needed each year. The impeller blades require thorough cleaning once in 6 months.
• Before any maintenance work is undertaken:
o Stop fan in accordance to regulations and disconnect all poles from mains supply.
o Wait until impeller is stationary.
o Make sure that a restart is not possible
• Use only original spare parts tested and approved by the manufacturer.
• The following safety notes must be observed when maintaining the machine.
• Replace the ball bearings of the motor whenever the grease utilization period has elapsed in accordance with the maintenance
instructions of the manufacturer.
• The technical maintenance includes periodic cleaning of the surfaces from accumulated dust and dirt.
• Use a soft dry brush or a vacuum cleaner to remove dust.
• Only use usual commercial cleaning material paying attention to the prescribed safety measures and do not use any abrasive
tools (surface protection will be destroyed)..
Prior to all servicing work:
• Bring the fan to a halt in the prescribed manner and completely isolate the fan from the mains supply.
• Wait until the rotor has come to a halt.
• Ensure that the machine cannot be switched on again.
• Clean the fan.
General Check:
• Too much bearing play?
• Lubricant leaking from the bearings?
• Surface protective coating damaged?
• Attention: Conveyed medium too aggressive?
• Unusual noises during operation?
• Fan output still sufficient for possibly extended or shortened ducting system?
Clean fan:
•Remove louver, orifice and impeller.
•Remove the fan casing in the wooden frame.
•Clean dirt on fan casing. Wash and clean louver, orifice.
•Clean impeller.
o Do not flood motor.
o Do not bend impeller, blades.
•Using a cloth dampened with kitchen detergent, remove any
dir from fan body, wipe dry with new cloth.
• Assembly fan.
•Control whether installation is correct:
o Motor impeller must rotate free
o The gap between impeller and casing must be regular.
o Checking direction of rotation is correct.
•Install the fan into air duct.
•Connect electric supply of motor.
Fig 1
We bring better air to life
Fig 5 Fig 6
We bring better air to life
Fig 3
Fig 4
Fig 2
Change of motor or impeller:
• Disconnect electrical supply in function box.
•Remove louver.
•Remove the fan casing in the wooden frame.
•Unscrews and remove orifice and impeller.
• Unscrews motor mounting and replace new motor.
• Assembly fan.
10. REPAIR
Before any repairs are undertaken please:
• Stop fan in accordance to regulations and disconnect all poles from mains supply.
• Wait until impeller is stationary.
• Make sure that a restart is not possible.
• Only use original spare parts manufactured and supplied by Breeze Fan.
05
•Control whether installation is correct:
o Motor and impeller must rotate freely
direction of rotation is correct. o Control whether
o Install maintenance cover if have.
o The gap between impeller and casing must be regular.
•Install the fan into air duct.
•Push into operation after repaired.
•Connect electric supply of motor.

06
11. TROUBLESHOOTING TABLE
PROBLEM POSSIBLE REASONS TROUBLESHOOTING
ŸWhen switching on the
unit the fan does not
start.
ŸCircuit breaker
tripping during the fan
start.
ŸLow air flow.
ŸThe automatic circuit breaker is
triggered by an abnormally high current
consumption due to a short circuit.
ŸClogging of air ducts or other ventilation
system elements. Impeller clogging.
Damaged air ducts. Air damper closure.
ŸDisconnect the fan from power mains and
contact the Breeze Seller.
ŸDo not turn on the fan again.
ŸClean the air ducts and other ventilation system
elements as well as the impeller.
ŸCheck the air ducts for damage.
ŸMake sure the air dampers and louver shutters
are open.
ŸPoor foundation ŸExcessive noise
ŸExcessive vibration
ŸReinforce the foundation
ŸFault installation ŸExcessive noise
Excessive vibration
ŸRe-adjust the installation
ŸLow voltage ŸInsufficient air flow ŸCheck power source
ŸSucked in objects /
Adhere dust
ŸMotor too hot
ŸExcessive noise
ŸExcessive vibration
ŸInspect and clean
ŸFaulty ducting ŸExcessive noise
ŸExcessive vibration
ŸInsufficient air flow
ŸInspect and adjust
ŸIncorrect wiring ŸRun abnormally ŸChange wiring
ŸNo power supply.
ŸMotor jamming.
ŸCheck the electrical connections and the power
switch status.
ŸTurn off the fan.
ŸTroubleshoot the impeller jamming.
ŸRestart the fan.
www.breeze.com.vn | [email protected]
We bring better air to life
USER’S MANUAL
CPD SERIES
Transport
• Our products are packed at the factory to suit the respectively agreed mode of transportation. Transport the fan in its original
packaging.
• Fans are protected against damage during shipment. If the unit cannot be installed and operated immediately, precautions
need to be taken to prevent deterioration of the unit during storage. The user assumes responsibility of the fan and
accessories while in storage. The manufacturer will not be responsible for damage during storage. These suggestions are
provided solely as a convenience to the user.
• Only use suitable means of transport, such as pallet trucks or fork-lift trucks or hoist machine.
• If the fan is to be transported by hand, ensure that supporting and carrying loads are kept within reasonable limits for the
personnel involved.
• The fans must not be dropped or thrown. Avoid scratches or rough handling during loading and unloading.
• Parts which have been stacked too high can collapse.
• Avoid a distortion of casing or blades or other damage.
• Danger ! Do not step under hanging loads.
Storage
• Store the unit in the manufacturer’s original packaging box in a dry closed ventilated premise with temperature range from +5˚С
up to +40˚С and relative humidity up to 85%.
• Store the fan in a dry, weather-protected location in its original packaging or protect it from the effects of dirt and the weather
until final assembly. Storage environment must not contain aggressive vapours and chemical mixtures provoking corrosion,
insulation and sealing deformation.
• Rotate fan wheel monthly and purge bearings once every three months.
• If storage of fan is in a humid, dusty or corrosive atmosphere, rotate the fan and purge the bearings once a month. Improper
storage which results in damage to the fan will void the warranty.
• Avoid lengthy storage periods (a maximum of one year is recommended) and check that the motor bearing assembly is in good
functional order prior to fitting. With storage times of more than 1 year, please check the bearings on soft running before
installation (turn by hand).
12. TRANSPORT AND STORAGE
Thank you for your cooperations!

Applied standard:
BREEZE INDUSTRIAL VENTILATION JOINT STOCK COMPANY
Vietnam
Head Office:
215D8 Nguyen Van Huong Street, Thao Dien Ward,
District 2, Ho Chi Minh City, Vietnam.
Tel: [phone] | Hotline: [phone]
Factory:
12 Road No. 570, Xom Moi Hamlet, Trung Lap Ha
Commune, Cu Chi District, Ho Chi Minh City, Vietnam.
Tel: [phone]
Ha Noi Office:
55, Alley No. 14, Vu Huu Street, Thanh Xuan Bac Ward,
Thanh Xuan District, Ha Noi City, Vietnam.
Tel: [phone] | Hotline: [phone].
Website: www.breeze.com.vn
Email: [email protected]
Singapore
Office:
No 15, Yishun Industrial Street
1, #03-29, WIN5 Singapore
S768091.
Tel: [phone]
Myanmar
Office:
No.13/B, Kan Yeik Thar
Street, Thingangyun
Township, Yangon, Myanmar.