brel-motors Brel BJE24D User manual

Page 1
Manual Brel 24mm electronic DC bi-directional radio middle motor
Type BJE24D
Read the manual be ore you begin the installation. I these instructions are not ollowed,
this may lead to de ects and injury in which warranty can’t be claimed.
warning:
Children cannot recognize the dangers of electrical equipment and may therefore not work with it.
It is important to ollow this instruction or your own sa ety.
1. Do not operate the motor in humid surroundings.
2. The motor must be installed correctly.
3. eep the antenna in a good condition and do not shorten.
The antenna should not come into contact with other metal
parts otherwise it will reduce the effect.
4. The motor must be protected from direct moisture influences.
5. BREL-Motors declares that this motor has been manufactured according to the guidelines of the CE standard 1999/5/EC
_______________________________________________________________________________
Functions remote control Changing batteries
DD-2702H
Works with all BREL transmitters:
Scan the QR code here or
The manual to download and
View the instruction videos
Visit our website www.BREL-HOME.com or
More manuals and in ormation
____________________________________________________________________________________
Technical data o the motor Type BJE24D
 Voltage motor: DC 12V
 Radiofrequency: 433.9 Mhz
 Power: 14 Watt
 Torque: 0.8 Nm
 Speed: 34 rpm
 Ampèrage : 1.18 A
 Moisture and dust protection: IP20
 Temperature range:
o - Normaal use: -10℃ tot +55℃

Page 2
______________________________________________________________________________
Functions motor Installation o the motor
Motor Cone
Wall bracket
Headrail
Motorbracket VB/PB/Roman
Bottomrail
_______________________________________________________________________________
Step 1 Setting up the irst remote/channel
P1 until 



 STOP until 2x 




OK
Hold P1 or put tension on the motor, the Press and hold the STOP button until the Transmitter/channel
product moves up and down. . product moves 2x up and down. has been set.
If NO end positions are set, the product will move in the pulse / step operation. Go then to STEP 2.
If end positions are set, the product will continue to its end position. Go then to STEP 4.
OTE: The correct end positions may not be set. Then go to OPTIO A.
______________________________________________________________________________
Step 2 Adjusting the direction o rotation
Only possible if no end positions are set, otherwise first option B (Delete end positions), after that, Step 2.
▲+▼ 1x 




OK
Press UP and DOWN button The direction of rotation of
simultaneously, until the product moves. the motor is OK.
_______________________________________________________________________________
Step 3 Manually setting the end position.
If no end positions have been set, the motor only moves in pulse mode.
1. Set the desired top position.
▲+ STOP Press and hold until 2x 




OK
Go with the OPERATING- Press and hold the STOP and UP button until The desired topposition is set.
buttons to the desired topposition. the motor moves up and down 2x.

Page 3
2. Set the desired down position.


 STOP+▼ 2x 




OK
Go with the OPERATING- Press and hold the STOP and DOWN button until The desired downposition is set.
buttons to the desired the motor moves up and down 2x.
downposition.
_______________________________________________________________________________
Step 4 Setting the desired third limit position (I desired)


 1x P2 1x 



 1x STOP 1x 



 1x STOP 2x 




OK
Set the desired Press 1x P2. Press 1x STOP button. Press 1x STOP button.
Third limit The product moves 1x The product moves 1x The product moves 2x up
position. up and down. up and down. and down for confirmation.
Press and hold STOP for 3 seconds to move to the set limit position.
The motor is now ready or use!
______________________________________________________________________________
Additional settings
____________________________________________________________________________
Option A Adjusting the top position I adjustment is not possible, go to Option B, then to Step 3.


 STOP +▲ until 



 

 STOP +▲ until 2x 




Go to the already Press at the same time Go to the new Press at the same time
set top position. STOP and UP until top position. STOP and UP button, until
the motor moves. the motor 2x moves.
___________________________________________________________________________
Adjusting the down position I adjustment is not possible, go to Option B, then to Step 3.


 STOP +▼ until 



 

 STOP +▼ until 2x 




Go to the already Press at the same time Go to the new Press at the same time
set bottom position, STOP and DOWN until bottom position. STOP and DOWN button, until
the motor moves. the motor 2x moves.
______________________________________________________________________________
Option B Deleting the end limits
1x P2 1x 



 1x ▼ 1x 



 1x P2 2x 




OK
Press 1x P2. The product Press the DOWN button. Press P2. The product The end positions
moves up down. The product moves 1x moves 2x up and down. are now deleted
up and down. from the memory.

Page 4
_______________________________________________________________________________
Option C Deleting the third limit position
1x P2 1x 



 1x STOP 1x 



 1x STOP 1x 




OK
Press 1x P2. Press 1x STOP button. Press 1x STOP button.
The product moves 1x up The product moves 1x up The product moves 1x up and
and down . and down. down for confirmation.
_______________________________________________________________________________
Option D Learn new transmitter/channel while maintaining end limits. Only possible when end limits are set.
= Already existing transmitter = ew transmitter
Method 1
P2 a until 



 P2 a until 



 STOP b until 2x 




OK
Press P2 of a. The product Press P2 o a. The product Press STOP o b. The product The transmitter b
moves 1x up and down. moves 1x up and down. moves 2x up and down. has been added.
Repeating the above will remove the new transmitter/channel.
Method 2
P2 a until 



 P2 a until 



 P2 b until 2x 




OK
Press P2 o a. The product Press P2 o a. The product Press P2 o b. The product The transmitter b
moves 1x up and down. moves 1x up and down. moves 2x up and down. has been added.
Repeating the above will remove the new transmitter/channel.
Method 3 (In case the old transmitter is lost or defect)
P1 until 1x 



 STOP b until 2x 




OK
Press P1 of a or put tension on the Press 1x STOP of b. The product The transmitter b
motor. The product moves 1x up and moves 2x up and down . is added
down.
Repeating the above will remove the new transmitter/channel.
_______________________________________________________________________________
Option E Pulse / jog control 1x 




▲+▼ until 1x 



 1x STOP
Pulse / jog on
Pulse / jog o
Press and hold UP and DOWN button, Press 1x STOP button.
until the product moves up and down.
2x 





Page 5
______________________________________________________________________________
Option F Speed control
1x 

 A 1x 

 A
1x P2 A until 



 O
Press 1x up of A. Press 1x up of A. The motor speed
has been increased
1x 

 A 1x 

 A
O
Press P2 o a. The product Press 1x down of A. Press 1x down of A. The motor speed
moves 1x up and down. toets A in. toets A in. has been reduced.
If the motor does OT react after this action, it is already at the highest or lowest speed.
_______________________________________________________________________________
Additional settings P1 button Can be used without a transmitter as an operating button
1x P1
The product moves up, stops or goes down when pressed P1
Press 1x P1 on the motor.
_______________________________________________________________________________
Switching o the receiver
P1, (6 sec.) until 2th x 




OK
Press and hold P1 until the product moves The Receiver switched off.
up and down for the 2th time.
To reactivate the receiver, briefly press P1 once.
______________________________________________________________________________
Changing the direction o rotation
P1, (10 sec.) until 3th x 




OK
Press and hold P1 until the product moves The direction of rotation has changed.
up and down for the 3th time.
_______________________________________________________________________________
Resetting to actory settings
P1, (14 sec.) until 4th x 




OK
Press and hold P1 until the product moves Resets to factory settings.
up and down for the 4th time.