Breville Dual Boiler BES920 User manual

Breville BES920 Descale Checklist
Time Required: 1.5 hrs
Ensure machine has been turned off and allowed to cool for at least 1 hr - this is very important
Pre-Prep:
Empty drip tray and return
Need flathead screwdriver
Remove Descale access plug
Prep:
Machine Off
Press and hold 1 CUP, then while still pressing, press and hold Power for 3 secs until RSET code appears.
press up/down arrow until DESC appears
press MENU to enter Descale mode. The 1 Cup button will light up.
Place teatowel over driptray to stop escaping steam
Done?
1Use Flathead screwdriver to SLOWLY open RIGHT side screw counterclockwise until valve is fully open. Do this REALLY SLOWLY
- if not water is released into drip tray, press and hold the 1 CUP button for 3 secs to release water
2 When all water is released, close the RIGHT hand screw clockwise until seated. Do not overtighten.
3Use Flathead screwdriver to SLOWLY open LEFT side screw counterclockwise until valve is fully open. Do this REALLY SLOWLY
- if not water is released into drip tray, press and hold the 1 CUP button for 3 secs to release water
4 When all water is released, close the LEFT hand screw clockwise until seated. Do not overtighten.
5
Empty Drip tray
6 Empty water tank
7
Remove water filter
8 Clean water tank
9Fill water tank with a bit more than 1 L of water. Any more than that is diluting it. Breville instructions say fill to the water line but sounds like dilution
to me. Breville also says fill with cold water whereas back of Breville descaler packet says warm water. Go with warm because dissolving is easier in
warm.
10 Dissolve solution in tank. Note Breville Descaler is made by Cafetto
11
Lock water tank back into machine

Descale: Done?
1 Press 1 Cup button - note water may flow through group head
2 Countdown reaches zero, however if you need to speed through to abort the process, press 1 Cup at any time to trigger next stage.
3Use Flathead screwdriver to SLOWLY open RIGHT side screw counterclockwise until valve is fully open. Do this REALLY SLOWLY
- if not water is released into drip tray, press and hold the 1 CUP button for 3 secs to release water
4 When all water is released, close the RIGHT hand screw clockwise until seated. Do not overtighten.
5Use Flathead screwdriver to SLOWLY open LEFT side screw counterclockwise until valve is fully open. Do this REALLY SLOWLY
- if not water is released into drip tray, press and hold the 1 CUP button for 3 secs to release water
6 When all water is released, close the LEFT hand screw clockwise until seated. Do not overtighten.
7
Empty Drip tray
8 Empty water tank and fill with CLEAN water to the FILL line.
Flush Boilers First Round:
1 Press 1 Cup button - note water may flow through group head
2 Countdown reaches zero, however if you need to speed through to abort the process, press 1 Cup at any time to trigger next stage.
3Use Flathead screwdriver to SLOWLY open RIGHT side screw counterclockwise until valve is fully open. Do this REALLY SLOWLY
- if not water is released into drip tray, press and hold the 1 CUP button for 3 secs to release water
4 When all water is released, close the RIGHT hand screw clockwise until seated. Do not overtighten.
5Use Flathead screwdriver to SLOWLY open LEFT side screw counterclockwise until valve is fully open. Do this REALLY SLOWLY
- if not water is released into drip tray, press and hold the 1 CUP button for 3 secs to release water
6 When all water is released, close the LEFT hand screw clockwise until seated. Do not overtighten.
7
Empty Drip tray
8 Empty water tank and fill with CLEAN water to the FILL line.
Flush Boilers First Second:
1 Press 1 Cup button - note water may flow through group head
2 Countdown reaches zero, however if you need to speed through to abort the process, press 1 Cup at any time to trigger next stage.
3Use Flathead screwdriver to SLOWLY open RIGHT side screw counterclockwise until valve is fully open. Do this REALLY SLOWLY
- if not water is released into drip tray, press and hold the 1 CUP button for 3 secs to release water
4 When all water is released, close the RIGHT hand screw clockwise until seated. Do not overtighten.
5Use Flathead screwdriver to SLOWLY open LEFT side screw counterclockwise until valve is fully open. Do this REALLY SLOWLY
- if not water is released into drip tray, press and hold the 1 CUP button for 3 secs to release water
6 When all water is released, close the LEFT hand screw clockwise until seated. Do not overtighten.
7
Empty Drip tray
8 Empty water tank and fill with CLEAN water to the FILL line.
9 Press POWER to Exit the Descale process