Breville Duo-Temp Pro BES810 series User manual

Suits all BES810 models
the Duo-Temp™Pro
Instruction Booklet
BES810BSS_ANZ_IB_E14.indd 2 27/06/2014 5:26 pm

CONGRATULATIONS
on the purchase of your new
Breville product
BES810BSS_ANZ_IB_E14.indd 2 27/06/2014 5:26 pm

3
CONTENTS
4Breville recommends safety first
8Know your Breville product
12 Operating your Breville product
17 Coffee making tips &
preparation
22 Care & cleaning
26 Troubleshooting
31 Coffees to try
BES810BSS_ANZ_IB_E14.indd 3 27/06/2014 5:26 pm

4
BREVILLE RECOMMENDS SAFETY FIRST
At Breville we are very safety conscious. We design and manufacture consumer products with
the safety of you, our valued customer, foremost in mind. In addition we ask that you exercise
a degree of care when using any electrical appliance and adhere to the following precautions.
READ ALL INSTRUCTIONS
BEFORE USE AND SAVE FOR
FUTURE REFERENCE
• Carefully read all
instructions before
operating and save for
future reference.
• Remove and safely discard
any packaging material
and promotional labels or
stickers before using the
Breville Duo-Temp™Pro for
the first time.
• To eliminate a choking
hazard for young children,
remove and safely discard
the protective cover fitted
to the power plug of this
appliance.
• Do not place the Breville
Duo-Temp™Pro near the
edge of a bench or table
during operation. Ensure
the surface is level, clean
and free of water and other
substances.
• Do not use the Breville
Duo-Temp™Pro on a sink
drain board.
• Do not place the Breville
Duo-Temp™Pro on or near
a hot gas or electric burner,
or where it could touch a
heated oven.
• Always ensure the
Breville Duo-Temp™Pro is
properly assembled before
connecting to power outlet
and operating. Follow the
instructions provided in
this book.
• The appliance is not
intended to be operated by
means of an external timer
or separate remote control
system.
• Do not use attachments
other than those provided
with the Breville
Duo-Temp™Pro.
• Do not attempt to operate
the Breville Duo-Temp™Pro
by any method other than
those described in this book.
IMPORTANT SAFEGUARDS
BES810BSS_ANZ_IB_E14.indd 4 27/06/2014 5:26 pm

5
BREVILLE RECOMMENDS SAFETY FIRST
5
• Use only cold, tap water in
the water tank. Do no use
any other liquid.
• Never use the Breville
Duo-Temp™Pro without
water in the water tank.
• Ensure the portafilter is
firmly inserted and secured
into the Group Head before
using the machine.
• Never remove the portafilter
during the extraction as the
machine is under pressure.
• Do not move the Breville
Duo-Temp™Pro whilst in
operation.
• Do not leave the Breville
Duo-Temp™Pro unattended
when in use.
• Do not touch hot surfaces.
Allow the Breville
Duo-Temp™Pro to cool
down before moving or
cleaning any parts.
• Do not place anything,
other than cups for
warming, on top of the
Breville Duo-Temp™Pro.
• Always switch off the
Breville Duo-Temp™Pro
by pressing the POWER
button to ‘Off’, switch off
at the power outlet and
unplug if appliance is to
be left unattended, if not in
use, before cleaning, before
attempting to move the
appliance, disassembling,
assembling and when
storing the appliance.
• Keep the appliance and
accessories clean. Follow
the cleaning instructions
provided in this book.
BES810BSS_ANZ_IB_E14.indd 5 27/06/2014 5:26 pm

6
BREVILLE RECOMMENDS SAFETY FIRST
IMPORTANT SAFEGUARDS
FOR ALL ELECTRICAL
APPLIANCES
• Unwind the power cord fully
before use.
• Do not let the power cord
hang over the edge of a
bench or table, touch hot
surfaces, or become knotted.
• To protect against electric
shock do not immerse
power cord, power plug or
appliance in water or any
other substance.
• This appliance can used
by children aged from
8 years and above if they
have been given supervision
or instruction concerning
the use of the appliance
in a safe way and if they
understand the hazards
involved. Cleaning and user
maintenance shall not be
made by children unless
they are older than 8 and
are supervised. Keep the
appliance and its cord out
of reach of children.
• This appliance is not
intended for use by
persons with reduced
physical, sensory or mental
capabilities, or lack of
experience or knowledge,
unless they have been
given supervision or
instruction concerning use
of the appliance by a person
responsible for their safety.
• Children should be
supervised to ensure
they do not play with the
appliance.
• It is recommended to
regularly inspect the
appliance. Do not use the
appliance if power cord,
power plug or appliance
becomes damaged in
anyway. Return the entire
appliance to the nearest
authorised Breville Service
Centre for examination
and/or repair.
• Any maintenance other
than cleaning should be
performed at an authorised
Breville Service Centre.
BES810BSS_ANZ_IB_E14.indd 6 27/06/2014 5:26 pm

7
BREVILLE RECOMMENDS SAFETY FIRST
• This appliance is
recommended for
household use only. Do
not use this appliance for
anything other than its
intended use. Do not use in
moving vehicles or boats.
Do not use outdoors.
Misuse may cause injury.
• The installation of a
residual current device
(safety switch) is
recommended to provide
additional safety protection
when using electrical
appliances. It is advisable
that a safety switch with a
rated residual operating
current not exceeding
30mA be installed in the
electrical circuit supplying
the appliance. See your
electrician for professional
advice.
WARNING
Fully unwind the cord before
use.
BES810BSS_ANZ_IB_E14.indd 7 27/06/2014 5:26 pm

KNOW
your Breville product
BES810BSS_ANZ_IB_E14.indd 8 27/06/2014 5:26 pm

9
FEATURES OF YOUR BREVILLE PRODUCT
PID TEMPERATURE CONTROL
Electronic PID temperature control for
increased temperature stability.
AUTO PURGE
Automatically adjusts water temperature
after steam for optimal coffee temperature.
THERMOCOIL HEATING SYSTEM
Integrated stainless steel water coil
accurately controls water temperature.
LOW PRESSURE PRE-INFUSION
Applies low pressure at the start of the
extraction to gently expand grinds for an
even extraction.
SWIVEL STEAM WAND
Easily adjusted to the ideal position for
texturing milk.
THE RAZOR™ PRECISION DOSE
TRIMMING TOOL
Trims the puck to the right level for a
consistent extraction
BES810BSS_ANZ_IB_E14.indd 9 27/06/2014 5:26 pm

10
I
K
J
L
KNOW YOUR BREVILLE PRODUCT
A
C
D
E
F
G
H
B
BES810BSS_ANZ_IB_E14.indd 10 27/06/2014 5:26 pm

11
KNOW YOUR BREVILLE PRODUCT
A. POWER button surround illuminates
when machine is switched on.
B. Thermocoil heating system accurately
controls water temperature.
C. Integrated removable tamper for
tamping control.
D. Group head for easy positioning of
the portafilter.
E. 54mm stainless steel portafilter with
commercial style spouts.
F. Extra-tall cup height for coffee mugs
G. Drip tray full indicator
H. Removable drip tray
I. Cup warming tray
J. SELECT button for steam or hot water
K. Control Dial for espresso, steam
and hot water.
L. Swivel steam wand easily adjusts to
perfect position for texturing milk.
NOT SHOWN
• Removable 1.8L water tank filled from
the top with integrated water filtration.
• Storage tray located behind the drip tray
for storage of accessories.
CUSTOM DESIGNED ACCESSORIES
• Razor™ Precision Dose Trimming Tool
• Single wall filter baskets for freshly
ground coffee.
• Advanced dual wall filter baskets for
pre-ground coffee.
• Water filter
• Stainless steel milk jug
CLEANING ACCESSORIES
• Cleaning tool
• Silicon cleaning disk
• Cleaning tablets
BES810BSS_ANZ_IB_E14.indd 11 27/06/2014 5:26 pm

OPERATING
your Breville product
BES810BSS_ANZ_IB_E14.indd 12 27/06/2014 5:26 pm

13
OPERATING YOUR BREVILLE PRODUCT
BEFORE FIRST USE
Machine Preparation
Remove and discard all labelling and
packaging materials attached to your
espresso machine. Ensure you have removed
all parts and accessories before discarding
the packaging. Clean parts and accessories
(water tank, portafilter, filter baskets and
jug) using warm water and a gentle dish
washing liquid and rinse well. Wipe the
outer housing and drip tray with a soft damp
cloth and dry thoroughly. Do not immerse
the outer housing, power cord or power plug
in water or any other liquid.
The water filter located inside the water tank
will need to be removed before washing the
water tank
Conditioning the Water Filter
• Remove filter from the plastic bag and
soak in a cup of water for 5 minutes.
• Rinse filter under cold running water.
• Wash the stainless steel mesh in
the plastic filter compartment with
cold water. Insert the filter into the
filter holder.
• Set the dial date 2 months ahead.
• To install filter, push down to lock
into place.
• Slide the water tank into position and
lock into place.
NOTE
Do not clean any of the parts or
accessories in the dishwasher.
FIRST USE
Initial Start Up
• Fill tank with water
• Press POWER button
• A pumping sound will be heard.
The machine will reach operating
temperature and go into ‘Standby’ mode.
Flushing the Machine
It is recommended to complete a water
flushing operation, without ground coffee, to
ensure the machine has been conditioned.
When the machine has reached ‘Standby’
mode, run the following 2 steps.
• Turn the Control Dial to the ‘Espresso’
position for 30 seconds.
• Turn the Control Dial to the ‘Steam’
position to activate steam for
10 seconds.
• Repeat this cycle several times.
NOTE
To purchase water filters contact
Breville Customer Service Centre
on 1300 139 798 (Australia) or
0800 273 845 (New Zealand).
BES810BSS_ANZ_IB_E14.indd 13 27/06/2014 5:26 pm

14
OPERATING YOUR BREVILLE PRODUCT
FILLING THE WATER TANK
• Ensure the water filter is securely fitted
inside the tank.
• Fill the water tank with cold tap water
to the maximum mark on the side of the
tank and slide the water tank back into
position at the back of the machine.
• Plug the power cord into power outlet
and switch On at power point.
• Press the POWER button. The POWER
button surround will flash while the
machine is heating. When the correct
temperature has been reached, all the
button surrounds on the control panel
will illuminate.
NOTE
Check the water level before use and
replace the water daily. The water
tank should be filled with fresh, cold
tap water before each use. Do not use
de-mineralised or distilled water or
any other liquid.
COFFEE PREPARATION
Dose & Tamping the Ground Coffee
If using whole bean coffee ground directly
before extracting, use the Single Wall Filter
Baskets. If using Pre-ground coffee, use
the Dual Wall Filter Baskets. Insert the
correct Filter Basket into the portafilter.
Fill the Filter Basket with ground coffee,
tap down to collapse the coffee, then using
the integrated tamper, tamp down firmly
(approx.. 15-20kg of pressure).
It’s important to apply consistent pressure
every time.
• As a guide to dose, the top edge of the
metal cap on the tamper should be level
with the top of the filter basket AFTER
the coffee has been tamped. This will
minimise under or over dosing the
coffee.
• Wipe excess coffee from the rim of the
filter basket to ensure a proper seal in
the group head is achieved.
TRIMMING THE DOSE
The Razor™ precision dose trimming tool
allows you to trim the puck to the right
level for a consistent extraction.
the Razor™
Precision dose trimming tool
Refer to Coffee Making Tips & Preparation,
page 17 for more details.
BES810BSS_ANZ_IB_E14.indd 14 27/06/2014 5:26 pm

15
OPERATING YOUR BREVILLE PRODUCT
EXTRACTING ESPRESSO
Insert the Portafilter into the Group Head
& lock into position. Turn the Control Dial
to the ‘Espresso’ position. A pumping noise
will be heard. After a few seconds, coffee will
begin to brew into the cup.
When sufficient coffee has flowed into
the cup, turn the Control Dial to ‘Standby’.
This will stop the flow of coffee. Breville
recommends approx. 30 sec of extraction.
NOTE
For optimal flavour when using a
1 CUP filter, you should extract approx.
30ml. When using a 2 CUP filter, you
should extract approx. 60ml.
LOW PRESSURE PRE-INFUSION
The low pressure pre-infusion gradually
increases water pressure to gently expand
grinds for an even extraction before
increasing to full pressure.
WARNING
The metal parts of the portafilter
will be very hot.
NOTE
If machine is run continuously for
30 minutes, allow machine to cool for
5 minutes before each use.
BES810BSS_ANZ_IB_E14.indd 15 27/06/2014 5:26 pm

16
OPERATING YOUR BREVILLE PRODUCT
TEXTURING MILK
The Duo Temp™ Pro is equipped with
a commercial style steam wand.
• Before inserting the steam wand into
the milk, it is recommended to purge
the steam wand.
• Turn the Control Dial to ‘Steam’.
• The ‘Steam’ LED will illuminate.
• It may take a few moments before the
steam appears.
• Pause the steam by returning the dial
back to the ‘Standby’ position. This will
avoid the milk splashing out of the jug.
• The Steam will Pause for 8 secs.
• Insert the wand into the milk and set the
Control Dial to the ‘Steam’ position to
texture milk.
• To stop the steam set the Control Dial
to the ‘Standby’ position and remove
the jug.
NOTE
When the espresso machine creates
steam, a pumping noise can be heard.
This is the normal operation of the
15 bar Italian pump.
HOT WATER
The machine features a separate Hot
Water function that dispenses hot water
from the Steam Wand.
To use the Hot Water function:
• Press the ‘SELECT’ button and the
Hot Water LED will illuminate.
• Direct the spout outlet towards the
drip tray.
• Turn the Control Dial to ‘Steam’.
To turn the hot water off, turn the Control
Dial to the ‘Standby’ position.
NOTE
The machine will automatically default
to ‘Steam’ when the appliance is first
switched on.
Both Steam and Hot Water functions
cannot be operated at the same time.
WARNING
Hot water may drip from the Steam
Wand. Always direct spout outlet
towards the drip tray.
AUTO PURGE
For extracting espresso immediately after
using the steam function, this machine
features an auto-purge function.
The auto purge function ensures the
ground coffee will not be burnt by the initial
water flow from the thermocoil being too
hot. The water is automatically released
internally into the drip tray ensuring that
the thermocoil is at optimal temperature
for extracting espresso. Your espresso
will always be extracted at the optimal
temperature ensuring only the best flavours
are extracted.
BES810BSS_ANZ_IB_E14.indd 16 27/06/2014 5:26 pm

17
COFFEE MAKING TIPS
& PREPARATION
BES810BSS_ANZ_IB_E14.indd 17 27/06/2014 5:26 pm

18
COFFEE MAKING TIPS & PREPARATION
PRE-HEATING
Heating your cup or glass
A warm cup will help maintain the coffee’s
optimal temperature. Preheat your cup by
rinsing with hot water and place on the cup
warming tray.
Heating the portafilter and filter basket
A cold portafilter and filter basket can
reduce the extraction temperature enough
to significantly affect the quality of your
espresso. Ensure the portafilter and filter
basket are preheated with hot water before
initial use. Wipe the filter and portafilter
dry before dosing with ground coffee as
moisture can encourage channelling
where water by-passes the ground coffee
during extraction.
Single Wall Filter Baskets
The Single Wall filters (1 & 2 CUP) are
designed to be used with freshly ground
coffee and allow you to experiment with
grind, dose, and tamp to create a more
balanced espresso.
2 Cup1 Cup
The Single Wall filters have no markings
on the underside of the filter.
Advanced Dual Wall Filter Baskets
The Dual Wall filters (1 & 2 CUP) are
designed to be used with pre-ground coffee
and regulate the pressure to help optimise
extraction and crema regardless of the
grind, dose or tamp pressure.
2 Cup1 Cup
The Dual Wall filters have DUAL WALL
stamped on the underside of the filter.
The Grind
When grinding coffee beans, the grind size
should be fine but not too fine. The grind
size will affect the rate at which the water
flows through the ground coffee in the filter
basket and the taste of the espresso.
If the grind is too fine (looks like powder
and feels like flour when rubbed between
fingers), the water will not flow through the
coffee when under pressure. The resulting
espresso will be OVER EXTRACTED, dark
in colour and bitter in flavour.
Coffee Dose and Tamping
• Wipe coffee basket with a dry cloth.
• If using Single Wall filter baskets,
grind enough coffee to fill the coffee
basket. You may need to experiment
with the amount of coffee to achieve
the correct dose.
• Tap the portafilter several times to
distribute the coffee evenly in the
filter basket.
BES810BSS_ANZ_IB_E14.indd 18 27/06/2014 5:26 pm

19
COFFEE MAKING TIPS & PREPARATION
• Tamp down firmly (using approx.
15-20kgs of pressure). It’s important to
apply consistent pressure every time.
• As a guide to dose, the top edge of the
metal cap on the tamper should be level
with the top of the filter basket AFTER
the coffee has been tamped. This will
minimise under or over dosing the
coffee.
• Wipe excess coffee from the rim of the
filter basket to ensure a proper seal in
the group head is achieved.
TRIMMING THE DOSE
The Razor™ precision dose trimming tool
allows you to trim the puck to the right
level for a consistent extraction.
Dose the Portafilter with freshly ground
coffee and tamp down with between
15-20kg of pressure.
the Razor™
Precision dose trimming tool
Insert the Razor™ into the coffee basket until
its shoulders rest on the rim of the filter
basket. The blade of the dosing tool should
penetrate the surface of the tamped coffee.
Rotate the Razor™ dosing tool back and forth
while holding the portafilter on an angle over
the knock box to trim off excess coffee.
Your coffee filter basket is now dosed with the
correct amount of coffee.
NOTE
When using the 1 CUP Single Wall
Filter basket, you may need to make
the grind finer and also decrease the
grind amount to ensure a correct
dose and extraction.
OPTIMUM 8-10g (1 CUP)
15-18g (2 CUP) 25-35 SECBALANCED
GRIND TAMPDOSE SHOT TIME
TOO FINE TOO MUCH
USE RAZOR TO TRIM
TOO LITTLE
INCREASE DOSE &
USE RAZOR TO TRIM
OVER 40 SEC
OVER EXTRACTED
BITTER •ASTRINGENT
TOO COARSE UNDER 20 SEC
UNDERDEVELOPED •SOUR
UNDER EXTRACTED
30-40lbs
(15-20kg)
TOO HEAVY
TOO LIGHT
EXTRACTION GUIDE
BES810BSS_ANZ_IB_E14.indd 19 27/06/2014 5:26 pm

20
PAge heAder.....
COFFEE MAKING TIPS & PREPARATION
PURGING THE GROUP HEAD
Before placing the portafilter into the group
head, run a short flow of water through
the group head, turning the Control Dial
to the ‘Espresso’ position. This will purge
any ground coffee residue from the group
head and stabilise the temperature prior to
extraction.
INSERTING THE PORTAFILTER
Place the portafilter underneath the group
head so that the handle is aligned with the
INSERT position. Insert the portafilter
into the group head and rotate the handle
towards the centre until resistance is felt.
EXTRACTING ESPRESSO
• Place pre-warmed cup(s) beneath the
group head and turn the Control Dial to
the ‘Espresso’ position until the required
volume is reached.
• As a guide, the espresso should start to
flow after 8-10 seconds (infusion time)
and should be the consistency
of pouring honey.
• If the espresso starts to flow before
6 seconds you have either under dosed
the filter basket and/or the grind is too
coarse. This is an UNDER EXTRACTED
shot.
• If the espresso starts to drip but doesn’t
flow after 15 seconds, you have either
over dosed the filter basket and/or
the grind is too fine. This is an
OVER EXTRACTED shot.
• A great espresso is about achieving
the perfect balance between sweetness,
acidity and bitterness.
• The flavour of your coffee will depend
on many factors, such as the type of
coffee beans, degree of roast, freshness,
coarseness or fineness of the grind and
dose of ground coffee.
• Experimenting by adjusting these
factors just one at a time can help to
achieve the taste of your preference.
TEXTURING MILK
There are two phases to texturing milk. The
first is stretching the milk to aerate it and the
second is swirling the milk to make it silky
smooth. These two operations should blend
into one.
• Always start with fresh cold milk.
• Fill the jug just below the V at the
bottom of the spout.
• Position the steam tip over the drip tray
and turn the Control Dial to STEAM
position, purging any condensed water.
• Turn the Control Dial to ‘Standby’
position to pause the steam, insert
steam wand tip into milk and turn dial to
STEAM position.
• Insert the steam tip 1-2cm below the
surface close to the right hand side of
the jug at the 3 o’clock position.
• Keep the tip just under the surface
until the milk is spinning clockwise,
producing a vortex (whirlpool effect).
BES810BSS_ANZ_IB_E14.indd 20 27/06/2014 5:26 pm