Brilliant Wonders 25650-100 Series User manual

Wireless Touch LED RGB Remote Controller
25650-100 Series
OPERATION & INSTALLATION QUICK REFERENCE
WARNINGS AND IMPORTANT SAFETY PRECAUTIONS
Be sure that the electrical system prior to installation conforms to all local codes and
ordinances. A licensed or certied electrician must install the electrical system to insure
that it follows all of the requirements of the National Electric Code (NEC). The electrician
may need to consult the local building inspector for code interpretation before installing
the 25650-100 wireless controller.
IMPORTANT NOTICE
Attention Installer: This manual contains important information about the installation,
operation, and safe use of this product. This information should be given to the owner
and/or operator of this equipment. When installing and using this electrical equipment,
basic safety precautions should always be observed.
Read all safety precautions and important instructions before attempting any electrical
wiring. Ensure that all power has been turned o at the power source. Failure to follow
safety warnings and instructions can result in severe injury, death, or property damage.
CMP recommends installation to be performed by a licensed professional.
INTRODUCTION
Thank you for choosing the CMP 25650-100 series controller. If you haven’t already done
so, please take a moment to read our safety information. To fully enjoy the features of
this controller, please read the entire manual before operating. Following these safety
requirements should prevent any damage to your new controller.
1. PERFORMANCE PARAMETERS
CONTROLLER
• Power input: 12 Volt DC
• Max Current: 5A x 3CH Max 15A
• Maximum load power: 180 Watts
• Change Mode: 32
• Scale Levels: 65536 steps/RGB
(16Bits/CH)
• Control Function: 8 touch buttons
• Operating temp: -30°C to 55°C
• Dimension: L8.3 in. x W1.6 in. x H1.2 in.
• Weight(net): 180g
REMOTE
• Power: Rechargeable 5 Volt DC
built in Lithium battery
• Working Current: 30mA
• Working Frequency: 2.4 GHZ
• Battery Capacity: 1000mAh
• Charge Time: <4 hours
• Normal Usage Time: 30 days
• Number of charge cycles: 500
• Operating range: up to 90 feet
(dependent on environment)
• Operating temp: -30°C to 55°C
• Dimension: 5.7”L x 2.2”W x 0.9”H
• Weight(net): 200g
Brilliant
Wonders
LED WATERFALLS
TM

2. KEY FEATURES
The remote control has 18 function buttons and 1 full-color touch circle. The controller
has 8 touch buttons.
HOW TO PAIR THE CONTROLLER WITH THE REMOTE
Press the “ON/OFF” key on the controller until you hear the “BEEP” sound, then press
the “1” key on the remote to activate the connection between the controller and remote
control. Press the “2” key to cancel the connection
3. LIGHT MODES
PAUSE
MODE MODE
SPEED SPEED
BRT BRT
ON/OFF
PAUSE
MODE+
MODE-
SPEED+
SPEED-
ON/OFF:
BRT+
BRT-
Turn on/off the Controller.
When touching the full-color circle, LED lights will
show the same color as the circle.
Controller sign
Button Description
Remote control sign
MODE+ MODE-/
Press the keys to select next mode or back to
previous mode.
SPEED+/SPEED-
Press the keys to quicken and slow color change speed
PAUSE
BRT+/BRT-
Press the keys to increase or decrease brightness,
keep pressing to adjust brightness continuously
set successfully when heard takq
Full Color
Touch
Circle
Nine DIY
Keys
Press once to stay at current color
Press again to resume color changing
Press this button in 3 seconds, and the buzzer
can be turned on or off
Press a key for 3 seconds and the controller will save the
current function mode automatically. Save up to 9 modes
and save repeatedly as well. Press the “PLAY” key to cycle
all saved modes. (this only plays the dynamic effects, static
effects will be skipped automatically)
3
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
Description
No. Mode
Description
No. Mode
Static red
Static green
Static blue
Static yellow
Static purple
Static cyan
Static white
RGB skipping
7 colors skipping
White strobe
7 colors strobe
Red fade out and fade in
Green fade out and fade in
Blue Fade out and fade in
Yellow fade out and fade in
Purple fade out and fade in
brightness adjustable
brightness adjustable
brightness adjustable
brightness adjustable
brightness adjustable
brightness adjustable
brightness adjustable
speed/brightness adjustable
speed/brightness adjustable
speed/brightness adjustable
speed/brightness adjustable
speed/brightness adjustable
speed/brightness adjustable
speed/brightness adjustable
speed/brightness adjustable
speed/brightness adjustable
speed/brightness adjustable
speed/brightness adjustable
speed/brightness adjustable
speed/brightness adjustable
speed/brightness adjustable
speed/brightness adjustable
speed/brightness adjustable
speed/brightness adjustable
speed/brightness adjustable
speed/brightness adjustable
speed/brightness adjustable
speed/brightness adjustable
speed/brightness adjustable
speed/brightness adjustable
speed/brightness adjustable
speed/brightness adjustable
Cyan fade out and fade in
White fade out and fade in
RGB fade out and fade in
y
Red Green color smooth
Red Blue color smooth
Green Blue color smooth
Red Yellow color smooth
Green Cyan color smooth
Blue purple color smooth
Green Yellow color smooth
Blue Cyan color smooth
Red Purple color smooth
Blue White color smooth
Yellow Purple Cyan color smooth
RGB color smooth
full color smooth

HH
H H HH
BLACK
GREEN
RED
LED MODULE
R
B
G
R
B
G
RG
LED MODULE
R
B
G
R
B
G
RG
LED MODULE
R
B
G
R
B
G
RG
LED MODULE
R
B
G
R
B
G
RG
DC12V
DC12V
LN
AC DC
AC220V
110V
POWER
SUPPLY
CLASS 2
WHITE
3. INSTALLATION AND WIRING DIAGRAM
Connected to RGB module as an example
Note: Ensure all wire connections and polarities are correct before applying power.
CONTROLLER MOUNTING
You must provide the controller enclosure
a. The enclosure or junction box must be installed per the National Electric
Code (NEC) requirements as well as comply with any local codes and regula-
tions
b. All wire used from the controller box to luminaire must be in conduit.
c. Min size of controller box must be 9" x 2" x 1.5".
d. The enclosure must be non-metallic(plastic) to ensure adequate RF signals
are achieved.
e. For product longevity, ensure proper ventilation where both the controller
and power supply may be mounted inside the same enclosure in elevated
outdoor temperatures.
CMP Plastic Outdoor Box
for Controller Only
25650-100-210
DO NOT INSTALL ANY OTHER ITEM
INSIDE CONTROLLER ENCLOSURE.
State listed Class 2 Power Supply
and Listed outdoor junction box
will have to be purchased and
installed.

4. CHARGING METHODS
1. When charging, connect the USB cable to the mobile charger or a computer
with USB interface. The remote control must be turned on to charge.
2. The blue indicator light ickers while charging, and will turn green when
fully charged
3. No memory eect in the lithium battery of the remote control. Follow the
standard charging procedure even for the rst three charges. There is no
need to over charge.
4. The red indicator light ickers when the battery is low and needs to be
charged soon. Charging in low battery will eect battery life.
5. REPLACEMENT PARTS & DIMENSIONS GUIDE
HH
H H HH
40mm
55mm
16mm
15mm
10mm10mm
203mm
20mm
211mm
145mm
22mm
30mm
HH
H H HH
40mm
55mm
16mm
15mm
10mm10mm
203mm
20mm
211mm
145mm
22mm
30mm
everything matters.
®
©2013 Custom Molded Products
www.c-m-p.com
sb0913
P/N DESCRIPTION
25650-100-300 REMOTE & CONTROLLER
25650-100-000 COLORWHEEL REMOTE
25650-100-100 CONTROLLER
COLORWHEEL REMOTE
LED CONTROLLER