Brite View BVW?200 User manual

0

1
TableofContents
TABLEOFCONTENTS............................................................................................................1
1.IMPORTANTINFORMATION............................................................................................2
2.INTRODUCTION................................................................................................................8
2.1PACKINGCONTENT....................................................................................................8
2.2OVERVIEW .................................................................................................................9
2.2.1BVW‐200T(TX):FULLHDVIDEOWIRELESSTRANSMITTER.........................................9
2.2.2BVW‐200R(RX):FULLHDVIDEOWIRELESSRECEIVER...............................................9
2.2.2BVW‐200R(RX):FULLHDVIDEOWIRELESSRECEIVER.............................................10
3.INSTALLATION ................................................................................................................ 11
STEP1:SETUPTHEBVW‐200TTRANSMITTER............................................................... 11
STEP2:SETUPTHEBVW‐200RRECEIVER ......................................................................12
STEP3:SETUPTHEIRBLASTEREXTENDERCABLE.........................................................13
STEP4:BOOTUPTHETRANSMITTERANDRECEIVER ...................................................14
STEP5:MOUNTINGTHEBVW‐200TOTHEWALL .........................................................18
4.TROUBLESHOOTING.......................................................................................................19
5.SUPPORTEDRESOLUTION..............................................................................................21
6.AUDIOBITRATESUPPORT .............................................................................................23
7.PRODUCTSPECIFICATION ..............................................................................................24


2
1.ImportantInformation
Pleasetakethetimetoreadthisusermanual
beforeusingtheBVW‐200TandBVW‐200R.
Itcontainsimportantinformationabout
operatingyourFullHDvideowirelesskit.

Ourlimitedwarrantyapplieswhentheproduct
ishandledproperlyforintendeduse,in
accordancewithitsoperatinginstruction.
However,thewarrantymaybevoidinthe
followingcases:
zRepair,productmodificationoralteration
havebeenperformedbyunauthorized
servicepersonnel
zDamagescausedbyaccidents,including
butnotlimitedto,lightning,water,fire,or
moisture
zUseofanACadapternotcompatiblewith
theproductanditsvoltagerating
zThemodelnumberontheproducthas
beenaltered,deleted,removedormade
illegible.

SafetyPrecautions
WARNING!

RISKOF
ELECTRICAL
SHOCK
DONOTOPEN

WARMING:
TOREDUCETHERISKOFELECTRICALSHOCK
DONOTREMOVETHECOVER
NOUSER‐SERVICEABLEPARTSAREINSIDE
REFERSERVICINGTOQUALIFIED
PERSONNEL

Danger:Becarefulwithelectricity.

zPowertotheunitsmustbeswitchedoff
beforeanyworkisundertaken,suchas
anyAVdeviceconnectionorTV
connection.
zPoweroutlet:Topreventelectricshock,
makesuretousetheappropriateAC
adaptersaspowersupplytothe
transmitterandthereceiver.
zPowercord:Besurethepowercordis
routedsothatitwillnotbesteppedonor
pinchedbyheavyitems.
zPoweroverloading:Avoidoverloading
electricaloutletsorextensioncordswhich
otherwisecouldresultinelectricshockor
fire.
zLightning:Disconnecttheproductfrom
thepowersourceifitisleftunattended
foralongperiodoftime,andtoprotect
theproductfromlightning.
zAlwaysdisconnectthepowercordfrom
thepoweroutletwhenyouarenotusing
yourFullHDVideowirelesskit.This
reducestheriskofelectricshocksorfire.

Warning
zThisproductshouldnotbeexposedto
drippingorsplashing.Noobjectfilled
withliquids,suchasvases,shouldbe
placedontheproduct.
zObjectEntry:Toavoidelectricshock,
neverstickanythingintheslotsonthe
caseorremovethecover.
zPlacereceiver/transmitteronaflat,hard
andstablesurface
zVentilation:Donotblocktheventilation
slotsonthereceiver/transmitterorplace
anyheavyobjectonthetopcover.
Blockingtheairflowcoulddamagethe
receiver.Arrangecomponentssothatair
canflowfreelyaroundthereceiver.
Ensurethatthereisadequateventilation
ifthereceiverisplacedinastand.
Putthereceiver/transmitterinaproperty
ventilatedarea,awayfromdirectsunlight
oranysourceofheat.
zWaterExposure:Toreducetheriskoffire
orelectricshock,donotexposethe
receiver/transmittertorainormoisture.
zThisisindoorsolution.
zOurcompanyhastherighttomodifythis
documentwithoutanynotice. 

3
EN55024Informationtechnology
equipment‐‐‐‐
Equipment‐‐‐Immunity
characteristics‐‐‐Limitsandmethodsof
measurement
EN301489‐1
ElectromagneticcompatibilityandRadio
spectrumMatters(ERM);ElectroMagnetic
Compatibility(EMC)standardforradio
equipmentandservices;
Part1:Commontechnicalrequirements





























































SpecialNotice
zNeverusethisproductnearbyanaircraft
ormedicalfacility.Itcancause
interferenceorundesirableeffectonthe
operationresult.
zUseofthisproductinthefollowing
locationsmayresultinabnormalvideo
andaudiooutput(noise,blockedimage...
etc,).
¾Productinstalledinthewallsmade
ofconcrete.
¾Productissituatednearthe
refrigeratorormetalfitment.
¾Aclutteredroomwherethe
wirelesssignalsmaybeblocked
zThisproducthasbeentestedand
manufacturedtocomplywitheach
country’ssafetyrules.However,thereis
noguaranteethatinterferencewillnot
occurinsomeinstallationscenario.Ifthe
interferencehappens,increasethe
distancebetweenthetransmitterand
receiver.
zBVW‐200mayinterfere5GHzwireless
devices,suchasroutersorotherwireless
devices.Therefore,ifyouhavean
802.11nrouter,configureittothe2.4
GHzbandratherthanthe5GHzband.
zOptimalrangebetweenBVW‐200
transmitterandreceiverisbetween2and
20meterswithinlineofsight.
EN55022Informationtechnology
equipment‐‐‐‐
Radiodisturbancecharacteristics‐‐‐Limits
andmethodsofmeasurement
EN61000‐3‐2Electromagneticcompatibility
(EMC)‐‐‐
Part3‐2:Limits‐‐‐Limitsforharmoniccurrent
emissions(equipmentinputcurrentupto
andincluding16Aperphase)
EN61000‐3‐3Electromagneticcompatibility
(EMC)‐‐‐
Part3:Limits‐‐‐Section3:Limitationof
voltagechanges,voltagefluctuationsand
flickerinpubliclow‐voltagesupplysystems,
forequipmentwithratedcurrent≦16Aper
phaseandnotsubjecttoconditional
connection
DECLARATIONOFCONFORMITY
ThisdevicecomplieswithPart15oftheFCC
Rules.Operationissubjecttothefollowing
twoconditions:
(1)Thisdevicemaynotcauseharmful
interference,and
(2)Thisdevicemustacceptanyinterference
received,includinginterferencethatmay
causeundesiredoperation.
EMI(ElectroMagneticInterference)tested.
TRADEMARKINFORMATION

zHDMI,theHDMILogoand
High‐DefinitionMultimediaInterface
aretrademarksofHDMILicensingLLC.
EN301489‐17
ElectromagneticcompatibilityandRadio
spectrumMatters(ERM);Electromagnetic
Compatibility(EMC)standardforradio
equipment;
Part17:Specificconditionsfor2,4GHz
widebandtransmissionsystems,5GHzhigh
performanceRLANequipmentand5,8GHz
BroadbandTransmittingSystems
EN60065Audio，videoandsimilar
electronicapparatus—Safetyrequirements

4
CAUTIONofRFmoduleonUS
region
zAnychangesormodificationsnot
expresslyapprovedbythegranteeofthis
devicecouldvoidtheuser'sauthorityto
operatetheequipment.
zThisequipmentmustbeinstalledand
operatedinaccordancewithprovided
instructionsandtheantenna(s)usedfor
thistransmittermustbeinstalledto
provideaseparationdistanceofatleast
20cmfromallpersonsandmustnotbe
co‐locatedoroperatinginconjunction
withanyotherantennaortransmitter.
End‐usersandinstallersmustbeprovided
withantennainstallationinstructionsand
transmitteroperatingconditionsfor
satisfyingRFexposurecompliance.
zOutdooroperationsinthe5150~
5250MHz,5600~5650MHzbandare
prohibited.
zThisdevicehasnoAd‐hoccapabilityfor
5250~5350MHzand5470~5725MHz.
zOutdooroperationsinthe
5470~5725MHzbandareprohibited.This
devicecouldnotbeusedinthe
5600~5650MHz.
zTheDevicenotoperationin
5600~5650MHz.
zIndustryCanadaregulatoryinformation
Operationissubjecttothefollowingtwo
conditions:(1)thisdevicemaynotcause
interference,and(2)thisdevicemust
acceptanyinterference,including
interferencethatmaycauseundesired
operationofthedevice.

zTheuseriscautionedthatthisdevice
shouldbeusedonlyasspecifiedwithin
thismanualtomeetRFexposure
requirements.Useofthisdeviceina
mannerinconsistentwiththismanual
couldleadtoexcessiveRFexposure
conditions.
zThefollowingstatementmustbeincluded
withallversionsofthisdocument
suppliedtoanOEMorintegrator,but
shouldnotbedistributedtotheenduser.
¾ThisdeviceisintendedforOEM
integratorsonly.
¾PleaseSeethefullGrantof
Equipmentdocumentforother
restrictions.
¾Thisdevicemustbeoperatedand
usedwithalocallyapprovedaccess
point.

zThefollowingregulatoryandSafety
noticesmustbepublishedin
documentationsuppliedtotheenduser
oftheproductorsystemincorporatingan
adapterincompliancewithlocal
regulations,Hostsystemmustbelabeled
with“ContainsFCCID:XXX‐XXXXX”,FCC
IDdisplayedonlabel.

SystemWarning
FEDERALCOMMUNICATIONSCOMMISSION
INTERFERENCESTATEMENT
Thisequipmenthasbeentestedandfoundto
complywiththelimitsforaClassBdigitaldevice,
pursuanttoPart15oftheFCCRules.These
limitsaredesignedtoprovidereasonable
protectionagainstharmfulinterferenceina
residentialinstallation.Thisequipment
generates,usesandcanradiateradiofrequency
energyand,ifnotinstalledandusedin
accordancewiththeinstructions,maycause
harmfulinterferencetoradiocommunications.
However,thereisnoguaranteethat
interferencewillnotoccurinaparticular
installation.Ifthisequipmentdoescause
harmfulinterferencetoradioortelevision
reception,whichcanbedeterminedbyturning
theequipmentoffandon,theuseris
encouragedtotrytocorrecttheinterferenceby
oneormoreofthefollowingmeasures:
zReorientorrelocatethereceiving
antenna.
zIncreasetheseparationbetweenthe
equipmentandreceiver.
zConnecttheequipmentintoanoutleton
acircuitdifferentfromthattowhichthe
receiverisconnected.
zConsultthedealeroranexperienced
radio/TVtechnicianforhelp.

5
CAUTION:UsingtheSystemin
theUS
zAnychangesormodificationsnot
expresslyapprovedbythegranteeofthis
devicecouldvoidtheuser'sauthorityto
operatetheequipment.
zThisequipmentmustbeinstalledand
operatedinaccordancewithprovided
instructionsandtheantenna(s)usedfor
thistransmittermustbeinstalledto
provideaseparationdistanceofatleast
20cmfromallpersonsandmustnotbe
co‐locatedoroperatinginconjunction
withanyotherantennaortransmitter.
End‐usersandinstallersmustbeprovide
withantennainstallationinstructionsand
transmitteroperatingconditionsfor
satisfyingRFexposurecompliance.
zOutdooroperationsinthe
5150~5250MHz,5600~5650MHzband
areprohibited.
zThisdevicehasnoAd‐hoccapabilityfor
5250~5350MHzand5470~5725MHz.
zOutdooroperationsinthe
5470~5725MHzbandareprohibited.This
devicecouldnotbeusedinthe
5600~5650MHz.
zThedevicenotoperationin
5600~5650MHz.


CAUTION:UsingthisSystemin
Canada

zIndustryCanadaregulatoryinformation
Operationissubjecttothefollowingtwo
conditions:
1. Thisdevicemaynotcause
interference,
2. Thisdevicemustacceptany
interference,includinginterference
thatmaycauseundesired
operationofthedevice.
Theuseriscautionedthatthisdeviceshouldbe
usedonlyasspecifiedwithinthismanualto
meetRFexposurerequirements.Useofthis
deviceinamannerinconsistentwiththis
manualcouldleadtoexcessiveRFexposure
conditions.





Europe–EUDeclarationof
Conformity
Thisdevicecomplieswiththeessential
requirementsoftheR&TTEDirective1999/5/EC.
Thefollowingtestmethodshavebeenappliedin
ordertoprovepresumptionofconformitywith
theessentialrequirementsoftheR&TTE
Directive1999/5/EC:

zEN60065:2002+A1:2006+A11:2008+A2
2010
zSafetyofInformationTechnology
Equipment

zEN50371:2002
Genericstandardtodemonstratethe
complianceoflowpowerelectronicand
electricalapparatuswiththebasic
restrictionsrelatedtohumanexposureto
electromagneticfields(10MHz‐300GHz)
‐‐Generalpublic

zEN301893V1.5.1:2008
BroadbandRadioAccessNetworks
(BRAN);5GHzhighperformanceRLAN;
HarmonizedENcoveringessential
requirementsofarticle3.2oftheR&TTE
Directive

zEN301489‐1V1.8.1:2008
ElectromagneticcompatibilityandRadio
SpectrumMatters(ERM);
ElectroMagneticCompatibility(EMC)
standardforradioequipmentand
services;Part1:Commontechnical
requirements

zEN301489‐17V2.1.12009
ElectromagneticcompatibilityandRadio
spectrumMatters(ERM);
ElectroMagneticCompatibility(EMC)
standardforradioequipmentand
services;Part17:Specificconditionsfor
2,4GHzwidebandtransmissionsystems
and5GHzhighperformanceRLAN
equipment

Hereby,brite‐viewdeclaresthatthisFullHD
Videowirelesskitisincompliancewiththe
essentialrequirementsandotherrelevant
provisionsofDirective1995/5/EC.

6
IndustryCanadaStatement
ThisdevicecomplieswithRSS‐210ofthe
IndustryCanadaRules.Operationissubjectto
thefollowingtwoconditions:(1)Thisdevice
maynotcauseharmfulinterference,and(2)this
devicemustacceptanyinterferencereceived,
includinginterferencethatmaycauseundesired
operation.
IMPORTANTNOTE:(IC:9078A‐ZRF31200)
RadiationExposureStatement:
ThisequipmentcomplieswithICradiation
exposurelimitssetforthforanuncontrolled
environment.Thisequipmentshouldbe
installedandoperatedwithminimumdistance
20cmbetweentheradiator&yourbody.
Caution:
(i) thedeviceforoperationintheband
5150‐5250MHzisonlyforindooruse
toreducethepotentialforharmful
interferencetoco‐channelmobile
satellitesystems;
(ii) high‐powerradarsareallocatedas
primaryusers(i.e.priorityusers)of
thebands5250‐5350MHzand
5650‐5850MHzandthattheseradars
couldcauseinterferenceand/or
damagetoLE‐LANdevices.
IMPORTANTNOTE:
Intheeventthattheseconditionscannotbe
met(forexamplecertainlaptopconfigurations
orco‐locationwithanothertransmitter),then
theCanadaauthorizationisnolonger
consideredvalidandtheICIDcannotbeused
onthefinalproduct.Inthesecircumstances,
theOEMintegratorwillberesponsiblefor
re‐evaluatingtheendproduct(includingthe
transmitter)andobtainingaseparateCanada
authorization.
Frenchtranslation:
CedispositifestconformeàlanormeCNR‐210
d'IndustrieCanadaapplicableauxappareils
radioexemptsdelicence.Sonfonctionnement
estsujetauxdeuxconditionssuivantes:(1)le
dispositifnedoitpasproduiredebrouillage
préjudiciable,et(2)cedispositifdoitaccepter
toutbrouillagereçu,ycomprisunbrouillage
susceptibledeprovoquerunfonctionnement
indésirable.
NOTEIMPORTANTE:(IC:9078A‐ZRF31200)
Déclarationd'expositionauxradiations:
Cetéquipementestconformeauxlimites
d'expositionauxrayonnementsICétabliespour
unenvironnementnoncontrôlé.Cet
équipementdoitêtreinstalléetutiliséavecun
minimumde20cmdedistanceentrelasource
derayonnementetvotrecorps.
(i) lesdispositifsfonctionnantdansla
bande5150‐5250MHzsontréservés
uniquementpouruneutilisationà
l’intérieurafinderéduirelesrisques
debrouillagepréjudiciableaux

7
systèmesdesatellitesmobilesutilisant
lesmêmescanaux;
(ii) Deplus,lesutilisateursdevraientaussi
êtreavisésquelesutilisateursde
radarsdehautepuissancesont
désignésutilisateursprincipaux(c.‐à‐d.,
qu’ilsontlapriorité)pourlesbandes5
250‐5350MHzet5650‐5850MHzet
quecesradarspourraientcauserdu
brouillageet/oudesdommagesaux
dispositifsLAN‐EL.
NOTEIMPORTANTE:
Danslecasoùcesconditionsnepeuventêtre
satisfaites(parexemplepourcertaines
configurationsd'ordinateurportableoude
certainesco‐localisationavecunautre
émetteur),l'autorisationduCanadan'estplus
considérécommevalideetl'IDICnepeutpas
êtreutilisésurleproduitfinal.Dansces
circonstances,l'intégrateurOEMserachargé
deréévaluerleproduitfinal(ycompris
l'émetteur)etl'obtentiond'uneautorisation
distincteauCanada.





8
2.Introduction
BVW‐200isaFullHDwirelesstransmissiondevice.

Thissolutiondeliversuncompressed1080pfullHDvideoandaudiocontenttoyourexistingHDTV
setwirelessly.Itoperatesthetransmissionin4.9GHz~5.9GHzfrequenciesanditcanadjustits
communicationfrequencyautomaticallyincaseofinterferencefromanotherRFsystem.With
built‐inOmni‐directionalantennas,itcantransmituncompressedvideocontentto20meters(66
feet)LOS(Lineofsight)withnolatency.

BothIRSensorExtenderCableandIRBlasterExtenderCableareincludedinthepackagesousers
canpointtheirremotecontroloftheAVsourceatthereceiverdirectlyfordeviceoperation.

2.1PackingContent

Pleasecheckwhetherthefollowingitemsarepresentinthepackage.Ifanyitemsmissedor
damaged,pleasecallyourdealer.


HDMI cable
Mini USB Power
Quick Installation
Anchors x2
IR Blaster cable
DC Power Adapter
BVW-200LR
BV
W
-200
L
T

9
2.2Overview

2.2.1BVW‐200T(TX):FullHDVideoWirelessTransmitter

FrontPanelButtonsandLEDs



MainUnitBackPanel













XPowerButtonwithLED
Indicator
Presstoturnthetransmitteron
andoff.Theindicatorinthe
powerbuttonislitinsolidblue
whenthepowerison,andturns
redinstandbymode.
YINFO.Button
PressthisbuttonforOSD
displayedtheinformationonthe
HDTVscreen.
ZStatusLED
Displaythevideostatusinformation.
ZIROUTBlasterExtenderJack
PlugtheIRBlasterExtender
CableintotheIROUTjackof
thetransmitter.
XDCIN
ForconnectingtheSWW1810Tpoweradapter.
[HDMIOUT
ConnecttoHDTVsetviaanHDMIcable.
YHDMIIN
ConnectTransmittertoHigh‐definitionaudio/videodevice
thathaveanHDMIportusingaprovidedHDMIcable.

10
2.2.2BVW‐200R(RX):FullHDVideoWirelessReceiver
FrontPanelButtonsandLEDs


















MainUnitBackPanel























XPowerButtonwithLEDindicator
Presstoturnthereceiveronandoff.The
indicatorinthepowerbuttonlightsupin
bluewhenthepowerison,andturnsred
instandbymode.
XHDMIOUT
ConnecttoHDTVsetviaan
HDMIcable.
YDCIN
Connecttoreceiver’s
poweradapter.
YINFO.Button
PressthisbuttonforOSD
displayedtheinformationonthe
HDTVscreen.
ZStatusLED
Displaythevideostatus
i
nformation
.

11
3.Installation

Step1:SetuptheBVW‐200Ttransmitter

ConnectTwoHigh‐DefinitionAudio/VideoSourcesandaHDTVtothetransmitter:




















































(1) Connectthetransmitter’s“HDMIIN”totheHigh‐DefinitionAVsources’“HDMIOUT”through
byHDMIcable.

(2) Connectthetransmitter’s“HDMIOUT”totheHDTVset’s“HDMIIN”portwithanHDMIcable
fortheloop‐throughconnection.

(3) ConnectthesuppliedpoweradaptertotheDCINjackofthetransmitterandawallsocket.The
LEDindicatorinthePOWERbuttonlightsupinbluewhentheBVW‐200Tisconnectedtothe
powermains.

12

Step2:SetuptheBVW‐200Rreceiver

HDTVsetConnectionwithBVW‐200R:




































(1) ConnecttheHDMIcabletotheHDMIOUTjackofthereceiverandtoyourHDTVset
(oranHDprojector).
PresstheSource/InputbuttonofyourTV’sremotetoselecttheappropriate“HDMI”
videoinput.
(2) ConnectthesuppliedpoweradaptertotheDCINjackofthereceiverandawall
socket.ThePOWERLEDindicatorlightsupinbluewhenthereceiverisconnectedto
thepowermains.

13
Step3:SetuptheIRblasterextendercable

Ifnecessary,connecttheInfrared(IR)blasterExtendercable.Userscanpointhand‐heldremote
controlofyourHighDefinitionAVequipmentatthereceiverortheHDTVsettooperatethe
sourcedevices,notexceedingthedistanceof66feetatLine‐of‐sight.






















(1) PlugtheIRblastercableintotheIROUTjackofthetransmitter.

(2) PleasetrytomanuallymovetheIRblasterinthefrontofthefrontpanelofyourHDdevice
andthenpressthekeyofremotecontroltosearchagoodpositionofIRresponse.Pastethe
IRblasterheadnearthefrontofIRsensorofyourHigh‐Definitionaudio/videodevices.

(3) WhentheIRblastercableisconnected,itrelaysinfraredcommandfromyourremotecontrol
tothedevice.UserscancontroltheirAVdevicesbypointingtheirremotecontroltothe
receiverinsteadoftotheirAVequipment.


Note:
(1) TheIRsensorsupports36KHz~56KHz(NEC,RC5,RC6)remote’ssignalprotocol.Therefore,itis
possiblethatsomedevicesmaynotbesupported.
(2) TheIRblastersupports47KHzremote’signalprotocol.

14
Step4:BootuptheTransmitterandReceiver

(1) Afterthepowercordispluggedintotheelectricaloutlet,theBVW‐200willbeturnedon
automatically.
(2) 








(3) IfitisinStandbymode(BothPOWERLEDoftransmitterandreceiverarelitinred),pressthe
POWERbuttoneithertransmitterorreceivertoturnonthetransmitterandthereceiver.Same
conditionforremotecontroloperation.

Pleasenote,theHDMIoutdisplayalwaysoneventhetransmitterinstandbymode.














(4) Duringthewarm‐up,thePOWERLEDwillblinkinblueuntilthesignallinkbetweenthe
BVW‐200TandtheBVW‐200Risestablished.Itwilltake15~20secondsforsystembootup
successfully.












15
(5) EnsureyourTVsetorprojectorisin“HDMIinput”mode,andisalreadypoweredon.













(6) Ifalloperationisnormal,thePOWERLEDandINFO./CHANNELLEDwillglowinsolidblue.
PleaserefertothebelowformcontainingdetailedLEDindicatorandOSDdescriptionof
transmitter/receiver:

Item/
Mode
StatusDescription
PowerLED
(onRX)
StatusLED
(onRX)
OSDDisplay
(onRX)
StandbyForpowersavingmode. StaticRedoff
InitialBoot
up/Warm
up
Itwillspend15~20
secondsforsystemboot
up.
Blinking
Blue
Blinking


Searching
available
channels
Continuingsearch
availablechannelsIf
systemcan’testablish
linkover80safter
initialization.
(NoteA&D)
Blinking
Blue
Blinking
 
  Loopingdisplay
thesetwoOSD
4level,looping.

16
Noinputfromselected
source
(NoteB)
StaticBlue
Blinking
(Quickly)


Videoformatnot
recognized
(NoteC)
StaticBlue
Blinking
(Slowly)


Wireless
linked
Mode
Videoformatis
recognized
StaticBlue StaticBlue -




Note:
A. IftheRFconnectionover80secandstillnotestablished,itmightlinklostorthetransmitteris
mostlikelyoutofrange.Youmayhavetoverifytherangeandadjustorshortenthedistance
betweenyourHDTVsetwiththetransmitterandthereceiver.Themaximumvideo
transmissionrangefor1080pcontentisupto66feetinlineofsight(LOS).<Theminimum
rangeis6.5feet.>

B. Pleasemakesurethesourceplayerhavebeenpoweronandswitchedthesignaloutputto
HDMIout;alsotrytore‐plugtheHDMIcabletomakesuretheHDMIconnectorhadsettled
well.

C. IfthereisnovideodisplayedandOSDdisplayed“NotSupportedFormat”,thisisanindication
thatthevideoframeratefromthecomputerisnotsupported,pleasereferchapter5toswitch
asupportedvideotiming.

D. IfyouhavemorethanonepairofBVW‐200,eachtransmitterandreceivershouldbeatleast
6.5feetawayfromoneanother.Ifboththetransmitterandthereceiverexistinthesameroom,
thesuggestedthedistancebetweenthetwois6.5feetminimum.

17

(7) OnScreenDisplay(OSD)vs.KeybuttonInstruction

XOnActivemode,PressthePOWERbuttononthetopofReceiver(ortransmitter),bothreceiver
andtransmitterenterStandbymodeandtransmitter’sHDMIoutison.
OSDDisplayed:(Display3secsandthenenterStandbymode.)
ON

YPresstheINFObuttononthetopofReceiver(ortransmitter),andSignalQuality,Source,
Channelandresolutionwillbedisplayedforuserreference.
OSDDisplayed:(Pressagainforexit.)
HDMI1CH101280x1024
  =OFF

ZKeeppresstheINFO.buttononthetopofReceiver(ortransmitter)over3sec.,OSDdisplayed
currentIRfrequencyon2ndHDTV,whileOSDdisplayedIRfreq.periodpressINFO.Buttonagain
forchangeIRBlasterfrequency,enabletoswitchIRBlasterfrequency47Kto56Kto36Krecurring.
(Note:IRblasterfrequencydefaultsettingis47KHz)
PressonceforcurrentIRfrequencystatusdisplay.TheOSDshows:
  HDMI1CH101280x1024
=38KHz

PressIRkeyagaintoswitchIRblasterfrequency.TheOSDshows:
  HDMI1CH101280x1024
=40KHz

NOTE:OnlythestatusoftheBVW‐200R(receiver)connectedtotheHDTVcanbedisplayedonthe
OSD.ThestatusoftheBVW‐200T(transmitter)HDMIoutcannotbedisplayed.

18

Step5:MountingtheBVW‐200totheWall

(1) Referthedrawingofthebottompagethat
haverelativepositionofthemainholesand
attachthispaperonwall.
(2) Drillpilotholes.


(3) InsertthesuppliedtwoAnchorsintothe
wall.








(4) Inserttwoscrewsintotheanchors.Leave
1/8 ” lengthformountingtheTransmitteror
receiver.
(5) 







(6) PlaceBVW‐200mainholesoverthe
protrudingscrewsandslidedowninto
position.

19
4.Troubleshooting
ProblemSolution
TheBVW‐200power
indicatorLEDdoesn't
lightup.
•CheckifthepowerplugsofBVW‐200T/BVW‐200Rareproperly
insertedintoafunctioningpoweroutlet.
Novideoisdisplayed
onyourTVscreen.
•Verifythatthepropercableshavebeenselectedandinstalled
betweentheBVW‐200T(transmitter)inputandyourHigh‐Definition
deviceoutput.
•OnyourTVside(connectedtotheBVW‐200R),selecttheHDMIas
inputsource.
•VerifythestatusofPOWERLEDandSOURCELEDindicatorof
BVW‐200asbelow:

PowerLEDFlashinginBlue
OSDdisplayed:  (4levelslooping)
*Ensurethetransmissionrangebetweenthetransmitterandthe
receiverisNOTover66feet(LOS‐lineofsight)transmissiondistance.
*Trytomovethetransmitterclosertothereceiver.

POWERLEDinSolidBlue+SlowandFlashingSOURCELED
OSDdisplayed:

*Ensureyourvideoresolutionandframerateisrecognized/supported
andwithinthetransmissionrange.
*ConnectthesourcedevicetoyourTVtocheckandmodifythevideo
formatcompatibility.
*CheckifyourvideoresolutionwithHDMIinputfromyourdeviceisset
among1080p,1080i,720p,576p,or480p.PleasereferChapter5for
thedetailsupportedResolution.

POWERLEDinSolidBlueSTATUSLEDFlashQuickly
OSDdisplayed:
