Briteq Spectra 3D Laser User manual

ENGLISH USER MANUAL
BRITEQ® 1/12 SPECTRA 3D LASER
OPERATION MANUAL
Thank you for buying this BRITEQ®product. To take full advantage of all possibilities and for your own safety,
please read these operating instructions very carefully before you start using this unit.
FEATURES
•This device was designed to produce decorative effect lighting and is used in light show systems.
•This is the perfect laser for those that can’t choose and simply want it ALL, even 3D-effects and ILDA-control!
…
•This eye-catching multicolor laser uses high quality 25kHz scanners, combined with 4 effect wheels to create
the most stunning effects:
•80 very smooth and soft moving RGB-patterns and beams to create laser curtains and many more
•Amazing 3D effect patterns and shows
•Incredible multicolor Polar effect shows
•The burst effect points multicolor laser beams in all directions for a stunning, room filling laser show
•Fabulous preprogrammed laser shows for all kinds of applications: clubs, discotheques, lounge bar, mobile
DJ, …
•Class-III 480mW RGB-laser based on 80mW Green CW laser (λ = 505nm), 300mW Blue CW laser (λ =
450nm) and 100mW Red CW laser (λ = 638nm).
•Several working modes:
•DMX-control: 1ch or 2ch for easy operation or 19 channels for full control
•ILDA mode: connect the laser to any PC with ILDA-compatible interface and use any professional
laser software to create stunning laser shows, create logos, etc.
•Standalone: sound activated (internal mic) or automatic
•Master/slave: wonderful synchronized shows
•Built-in microphone
•3-digit LED display for easy menu navigation
•Key actuated on/off switch and emergency switch (interlock) input for additional safety
•Complies to EN/IEC 60825-1: 2014 for Laser Safety
BEFORE USE
•Before you start using this unit, please check if there’s no transportation damage. Should there be any, do
not use the device and consult your dealer first.
•Important: This device left our factory in perfect condition and well packaged. It is absolutely necessary for
the user to strictly follow the safety instructions and warnings in this user manual. Any damage caused by
mishandling is not subject to warranty. The dealer will not accept responsibility for any resulting defects or
problems caused by disregarding this user manual.
•Keep this booklet in a safe place for future consultation. If you sell the fixture, be sure to add this user manual.
Check the contents:
Check that the cardboard box contains the following items:
•Spectra 3D laser
•Remote control connector
•2 keys (for key switch)
•Mains cable
•Operating instructions

ENGLISH USER MANUAL
BRITEQ® 2/12 SPECTRA 3D LASER
SAFETY INSTRUCTIONS:
•To protect the environment, please try to recycle the packing material as much as possible.
•To prevent fire or shock hazard, do not expose this appliance to rain or moisture.
•To avoid condensation to be formed inside, allow the unit to adapt to the surrounding temperatures when bringing it into
a warm room after transport. Condense sometimes prevents the unit from working at full performance or may even cause
damages.
•This unit is for indoor use only.
•Don’t place metal objects or spill liquid inside the unit. Electric shock or malfunction may result. If a foreign object enters
the unit, immediately disconnect the mains power.
•Locate the fixture in a well ventilated spot, away from any flammable materials and/or liquids. The fixture must be fixed
at least 50cm from surrounding walls.
•Don’t cover any ventilation openings as this may result in overheating.
•Prevent use in dusty environments and clean the unit regularly.
•Keep the unit away from children.
•Inexperienced persons should not operate this device.
•Maximum safe ambient temperature is 40°C. Don’t use this unit at higher ambient temperatures.
•Make sure the area below the installation place is free from unwanted persons during rigging, de-rigging and servicing.
•Allow the device about 10 minutes to cool down before to start servicing.
•Always unplug the unit when it is not used for a longer time or before to start servicing.
•The electrical installation should be carried out by qualified personal only, according to the regulations for electrical and
mechanical safety in your country.
•Check that the available voltage is not higher than the one stated on the unit.
•The power cord should always be in perfect condition. Switch the unit immediately off when the power cord is squashed
or damaged. It must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a
hazard.
•Never let the power-cord come into contact with other cables!
•This fixture must be earthed in order to comply with safety regulations.
•Don’t connect the unit to any dimmer pack.
•Always use an appropriate and certified safety cable when installing the unit.
•In order to prevent electric shock, do not open the cover. There are no user serviceable parts inside.
•Never repair a fuse or bypass the fuse holder. Always replace a damaged fuse with a fuse of the same type and
electrical specifications!
•In the event of serious operating problems, stop using the fixture and contact your dealer immediately.
•The housing and the lenses must be replaced if they are visibly damaged.
•Please use the original packing when the device is to be transported.
•Due to safety reasons it is prohibited to make unauthorized modifications to the unit.
Important: Never look directly into the light source! Don’t use the effect in the presence of persons suffering from epilepsy.
CAUTION: To reduce the risk of electric shock, do not remove the
top cover. No user-serviceable parts inside. Refer servicing to
qualified service personnel only.
The lightning flash with arrowhead symbol within the equilateral triangle is intended to alert the use or
the presence of un-insulated “dangerous voltage” within the product’s enclosure that may be of
sufficient magnitude to constitute a risk of electric shock.
The exclamation point within the equilateral triangle is intended to alert the user to the presence of
important operation and maintenance (servicing) instructions in the literature accompanying this
appliance.
This symbol means: indoor use only
This symbol means: Read instructions
This symbol determines: the minimum distance from lighted objects. The minimum distance between
light-output and the illuminated surface must be more than x meters

ENGLISH USER MANUAL
BRITEQ® 3/12 SPECTRA 3D LASER
LASER SAFETY INSTRUCTIONS:
•According to the EN/IEC 60825-1: 2014 regulations, this laser falls under the classification 3B. Direct eye
exposure can be dangerous.
DANGER: LASER RADIATION !
Avoid direct eye exposure! Laser radiation can cause eye damage
and/or skin damage. All protective measures for a safe operation of
this laser must be applied.
•This product is a so-called show laser, emitting radiation with a wavelength spectrum between 400 and 700
nm and producing lighting effects for shows.
•Laser Light is different from any other light source with which you may be familiar. The light from this product
can potentially cause eye injury if not set up and used properly. Laser light is thousands of times more
concentrated than light from any other kind of light source. This concentration of light power can cause
instant eye injuries, primarily by burning the retina (the light sensitive portion at the back of the eye). Even if
you cannot feel “heat” from a laser beam, it can still potentially injure or blind you or your audience.
•Even very small amounts of laser light are potentially
hazardous even at long distances.
•Never look into the laser aperture or laser beams
•Never direct the laser beam to people or animals and
never leave this device running unattended.
•This laser may only be used for shows. The operation
of a class 3Bshow laser is only allowed if the operation
is controlled by a skilled and well-trained operator.
•Depending on the classification, operating a laser
product can produce laser radiation that may cause
permanent eye damage and/or skin damage. The legal instructions for using a laser product vary from
country to country. The user must always inform himself on the legal instructions valid in his country and
apply them to his situation.
•In some countries, the installation or the operation of lasers is subject to approval. Please contact your local
authorities for country-specific safety regulations and guidelines for the operation of laser devices.
Please note that BRITEQ cannot be made liable for damages caused by incorrect installations and unskilled
operation!
WARNING LABEL LOCATIONS
A. APERTURE logos
or
These warning labels indicate the laser emission aperture
on the device: the emitted laser light is potentially
dangerous. NEVER look directly into the laser beam. Risk
of eye injury and / or blinding!
B. WARNING logo
CAUTION –CLASS 3B LASER RADIATION WHEN OPEN.
Avoid exposure to the beam.
C. Multilingual warning sticker
Warning –laser radiation, avoid exposuree to beam.
Class 3B laser product.
IEC/EN 60825-1:2014
Wavelength: 450-505-638nm
Laser radiation: CW <500mW

ENGLISH USER MANUAL
BRITEQ® 4/12 SPECTRA 3D LASER
DESCRIPTION REAR PANEL:
1. ILDA THROUGH: to link the ILDA signal to the next “Spectra-3D Laser” unit.
2. SAFETY EYEBOLT: used to attach a safety cable when the unit is rigged (see paragraph “overhead
rigging”
3. DISPLAY: shows the selected DMX address when the unit is in DMX-mode. Apart from DMX-mode you
can also select 4 other working modes, see further to learn
more about these modes.
4. INTERNAL MICROPHONE: The built-in microphone is used
to synchronize the laser show to the beat of the music.
5. INTERLOCK input: used to connect the optional emergency
stop switch (see picture). When you push this switch the laser
beam will disappear immediately.
IMPORTANT! For your own safety we strongly recommend to connect this optional switch!
THERE WILL BE NO LASER OUTPUT WHEN THE INTERLOCK INPUT IS NOT USED!
Temporary solution: install the spare connector on the laser. (see picture)
6. ON/OFF KEY ACTIVATED SWITCH: used to switch the unit on/off. Use the keys to make sure only a
skilled operator is able to switch the laser on.
7. MAIN ON/OFF SWITCH: used to switch the unit on/off.
8. MAINS INPUT: with IEC socket and integrated fuse holder, connect the supplied mains cable here.
9. EARTH CONNECTION
10. DMX OUTPUT: 3pin female XLR-connector used to connect the LASER with the next unit in the DMX
chain.
11. DMX INPUT: 3pin male XLR-connector used to connect universal DMX-cables. This input receives
instructions from a DMX-controller.
12. CONTROL PANEL: Used to select the different functions of the laser, see further to learn how to operate
the unit.
•FUNC: used to browse the different functions and working modes in the menu
•UP: used to go to the upper option or to increase a parameter of a function or working mode
•DOWN: used to go to a lower option or to decrease a parameter of a function or working mode
•ENTER: used to confirm your setting/selection
13. ILDA INPUT: used to connect the laser to an ILDA certified interface of a computer, see further for more
information.
14. COOLING FAN: used to cool the components inside the enclosure. Make sure to never cover this fan
outlet + never cover the small air inlets that are situated on the left and right side of the unit! Take care to
clean the air inlets and fan when needed.

ENGLISH USER MANUAL
BRITEQ® 5/12 SPECTRA 3D LASER
DESCRIPTION FRONT PANEL:
15. LASER OUTPUT: the laser beam exits the enclosure, make sure to NEVER look inside the unit through
this opening while the laser effect is switched on!
16. POWER LED: indicates that the unit is switched on.
17. MUSIC LED: flashes to the sound of the music detected by the internal microphone.
OVERHEAD RIGGING
•Important: The installation must be carried out by qualified service personal only. Improper
installation can result in serious injuries and/or damage to property. Overhead rigging requires
extensive experience! Working load limits should be respected, certified installation materials
should be used, the installed device should be inspected regularly for safety.
•Make sure the area below the installation place is free from unwanted persons during rigging, de-rigging
and servicing.
•Locate the fixture in a well ventilated spot, far away from any flammable materials and/or liquids. The fixture
must be fixed at least 50cm from surrounding walls.
•The device should be installed out of reach of people and outside areas where persons may walk by or be
seated.
•Before rigging make sure that the installation area can hold a minimum point load of 10times the device’s
weight.
•Always use a certified safety cable that can hold 12 times the weight of the device when installing the unit.
This secondary safety attachment should be installed in a way that no part of the installation can drop more
than 20cm if the main attachment fails.
•The device should be well fixed; a free-swinging mounting is dangerous and may not be considered!
•Don’t cover any ventilation openings as this may result in overheating.
•The operator has to make sure that the safety-relating and machine-technical installations are approved by
an expert before using them for the first time. The installations should be inspected every year by a skilled
person to be sure that safety is still optimal.
CAUTION EYEDAMAGE: Always position the laser in a way that prevents the audience
from looking directly into the laser beams. The installation should assure that the beam
will not strike the audience.

ENGLISH USER MANUAL
BRITEQ® 6/12 SPECTRA 3D LASER
HOW TO SET UP AND CONTROL THE UNIT
FUNCTION MENU:
GENERAL SETTINGS
Pattern X/Y mirror control setup:
•Press the FUNC-button until the display shows one of
the 4 displays on the right.
•Press the UP / DOWN buttons to choose one of the
four mirror options:
•Press the ENTER-button to confirm your choice.
MUSIC INPUT SENSITIVITY:
The unit can work to rhythm of the beat when used in sound activated mode
To set the input sensitivity, follow these steps:
•Press the FUNC-button until the display shows “S 0” …”S 9”
•Press the ENTER-button to confirm your choice.
•Use DOWN and UP button to select a value between “S 0” (very low sensitivity) and “S 9” (high sensitivity).
•Once the mode is selected, press the ENTER button save it.
You can operate the unit in 5 ways:
#1 STANDALONE:
The laser automatically runs a preprogrammed sequence. Select this mode when only 1 laser is used
(standalone) or when the laser is placed as the first (master) unit in a chain with several LASERs.
•Press the FUNC-button until the display shows one of the following: Soo, Son, SoL, Sob, S3d, Sou, Auo,
Aun, AuL, Aub, or A3d.

ENGLISH USER MANUAL
BRITEQ® 7/12 SPECTRA 3D LASER
•Now use the UP or DOWN buttons to select one of the options (see chart below). You have the choice
between automatic programs (Auo, Aun, AuL, Aub, A3d) or sound controlled programs (Soo, Son, SoL,
Sob, S3d, Sou)
•Press the ENTER-button to confirm your choice.
The laser automatically runs a preprogrammed sequence.
You can connect several SPECTRA 3DLASERs together: just put the first unit of the chain in one of the
automatic effect modes and all other units in “Slave mode” (display shows “SLA”) to make them all work in
perfect sync!
DISPLAY
STAND ALONE MODE PREPROGRAM EFFECT
AUT
Automatic Random Show of the 5 Effects
A3d
Laser 3D Effect Auto Show
AUB
Scanned Beam Effect Auto Show
AUL
Laser Lumia Effect Auto Show
AUN
Burst Grating Effect Auto Show
AUO
Laser Universal Effect Auto Show
Sou
Sound Activated Random Show of the 5 Effects
S3d
Sound Activated Show of the 3D effect
Sob
Sound Activated Show of the Scanned Beam Effect
SoL
Sound Activated Show of the Laser Lumia Effect
Son
Sound Activated Show of the Burst Grating Effect
Soo
Sound Activated Show of the Laser Universal Effect
#2 MASTER / SLAVE MODE:
You can connect several SPECTRA 3DLASERs together: just put the first unit of the chain in one of the
standalone effect modes (see #1Standalone)and all other units in “Slave mode” (display shows “SLA”) to
make them all work in perfect sync!
The “slave” lasers follow the instructions given by the first Spectra 3D laser (master) in the chain.
Settings for the slave units:
•Connect the DMX input of the laser to the DMX output of the previous laser in the chain.
•Press the FUNC-button until the display shows “SLA”
•Press the ENTER-button to confirm your choice.
#3 DMX512 MODE:
The laser can be controlled by any standard DMX-controller in 3 different DMX-modes:
•1 CHANNEL MODE: for extremely easy setup and use! (display shows “1Ch”)
•2 CHANNEL MODE: for extremely easy setup and use! (display shows “2Ch”)
•19 CHANNEL MODE: for full control of all possibilities. (display shows “19h”)
•Connect the DMX input of the laser to the DMX output of the previous unit in the chain or directly to the
DMX-output of your controller.
•Press the FUNC-button until the display shows: “1Ch”, “2Ch” or “19h”.
•Press the UP/DOWN buttons to select the DMX-mode. (1Ch, 2Ch or 19ch)
•Press the ENTER-button to confirm your choice.
•Press the FUNC-button: the 3 digit number on the display starts blinking.
•Press the UP/DOWN buttons to select the DMX-address
•Press the ENTER-button to confirm your choice.

ENGLISH USER MANUAL
BRITEQ® 8/12 SPECTRA 3D LASER
Note: the display blinks when the unit is in DMX-mode and no DMX-signal is detected.
Some more information on DMX512:
The DMX-protocol is a widely used high speed signal to control intelligent light equipment.
You need to “daisy chain” your DMX controller and all the connected light effects with a
good quality XLR M/F balanced cable. To prevent strange behavior of the light effects,
due to interferences, you must use a 90Ω to 120Ω terminator at the end of the chain.
Never use Y-splitter cables, this simply won’t work!
Each effect in the chain needs to have its proper starting address so it knows which commands from the
controller it has to decode.
DMX Channels Chart When ILDA is NOT connected
1-CHANNEL DMX-CONFIGURATION (ILDA IS NOT CONNECTED):
CHANNEL
VALUE
FUNCTION
CH 1
MODE
000-018
Laser OFF
019-036
AUT Auto Show with Mixed 5 effect
037-054
A3D Laser 3D Effect Auto Show
055-072
AUB Scanned Beam Effect Auto Show
073-090
AUL Laser Lumia Effect Auto Show
091-108
AUN Burst Grating Effect Auto Show
109-126
AUO Laser Universal Effect Auto Show
127-144
SOU Sound Show with Mixed 5 Effect
145-162
S3D Sound show with LASER 3D
163-180
SOB Sound show with Scanned Beam
181-198
SOL Sound show with LASER LUMIA
199-216
SON Sound show with Burst Grating
217-234
SOO Sound show with Laser Universal
235-255
SOU Sound Show with Mixed 5 Effect
2-CHANNEL DMX-CONFIGURATION (ILDA IS NOT CONNECTED):
CHANNEL
VALUE
FUNCTION
CH 1
MODE
000-018
Laser OFF
019-036
AUT Auto Show with Mixed 5 effect
037-054
A3D Laser 3D Effect Auto Show
055-072
AUB Scanned Beam Effect Auto Show
073-090
AUL Laser Lumia Effect Auto Show
091-108
AUN Burst Grating Effect Auto Show
109-126
AUO Laser Universal Effect Auto Show
127-144
SOU Sound Show with Mixed 5 Effect
145-162
S3D Sound show with LASER 3D
163-180
SOB Sound show with Scanned Beam
181-198
SOL Sound show with LASER LUMIA
199-216
SON Sound show with Burst Grating
217-234
SOO Sound show with Laser Universal
235-255
AUT Auto Show with Mixed 5 effect
CH2
000-234
Slow to Fast
235-255
ORIGINAL SPEED

ENGLISH USER MANUAL
BRITEQ® 9/12 SPECTRA 3D LASER
19 CHANNEL DMX-CONFIGURATION (ILDA IS NOT CONNECTED):
IMPORTANT REMARK: DMX Channel1 is used to set the different working modes of the laser.
•To use the laser in full 19 channel mode, channel 1 must be set to value 235 or higher.
•Depending on the DMX-values of channel1, different mode can be applied:
CHANNEL
VALUE
FUNCTION
CH 1
MODE
000-018
Laser OFF
019-036
AUT Auto Show with Mixed 5 effect
037-054
A3D Laser 3D Effect Auto Show
055-072
AUB Scanned Beam Effect Auto Show
073-090
AUL Laser Lumia Effect Auto Show
091-108
AUN Burst Grating Effect Auto Show
109-126
AUO Laser Universal Effect Auto Show
127-144
SOU Sound Show with Mixed 5 Effect
145-162
S3D Sound show with LASER 3D
163-180
SOB Sound show with Scanned Beam
181-198
SOL Sound show with LASER LUMIA
199-216
SON Sound show with Burst Grating
217-234
SOO Sound show with Laser Universal
235-255
DMX MODE
CH 2
GROUP
000-051
1 Group Patterns.
052-103
2 Group Patterns
104-155
3 Group Patterns
156-207
4 Group Patterns
208-255
5 Group Patterns
CH 3
PATTERN
000-255
Every 16 for 1 Group, total 16 patterns.
CH 4
COLOR
000-007
Original
008-015
Red
016-023
Green
024-031
Yellow
032-039
Blue
040-047
Purple
048-055
Light Blue
056-063
White
064-111
Color Rolling
112-159
Color Jumping
160-127
Color Moving
208-255
Strobing
CH 5
CLIPING
000
Full pattern without clipping
001-127
0%~99% fixed pattern clipped
128-255
Clipping Speed
CH 6
ZOOMING
000-127
100%-5% fixed pattern zoomed
128-169
Zooming IN
170-209
Zooming OUT
210-255
Alternately Zooming
CH 7
ZOOM SPEED
000-255
Fast to Slow
CH 8
Y AXIS
ROLLING
000-127
0 -359 degree fixed Y axis rolled
128-191
Clockwise rolling
192-255
Anticlockwise rolling
CH 9
ROLL SPEED
0-255
Fast to Slow
CH 10
X AXIS
ROLLING
000-127
0 -359 degree fixed X axis rolled
128-191
Clockwise rolling
192-255
Anticlockwise rolling
CH 11
ROLL SPEED
0-255
Fast to Slow
CH 12
000-127
0 -359 degree fixed Z axis rolled

ENGLISH USER MANUAL
BRITEQ® 10/12 SPECTRA 3D LASER
Z AXIS
ROLLING
128-191
Clockwise rolling
192-255
Anticlockwise rolling
CH 13
ROLL SPEED
0-255
Fast to Slow
CH 14
Y AXIS
MOVING
000-127
128 different fixed position on X axis
128-191
Clockwise moving
192-255
Anticlockwise moving
CH 15
MOVE SPEED
0-255
Fast to Slow
CH 16
X AXIS
MOVING
000-127
128 different fixed position on Y axis
128-191
Clockwise moving
192-255
Anticlockwise moving
CH 17
MOVE SPEED
0-255
Fast to Slow
CH18
Grating
Rotation
000-004
No grating rotating
005-127
Clockwise grating rotating
128-133
No grating rotating
134-255
Anticlockwise grating rotating
CH19
Grating Effect
000-031
Laser 3D Effect
032-063
Scanned Beam Effect (Pattern Effect)
064-095
Laser Lumia Effect
096-127
Scanned Beam Effect (Pattern Effect)
128-159
Burst Grating Effect
160-191
Scanned Beam Effect (Pattern Effect)
192-223
Laser Universal Effect
224-255
Scanned Beam Effect (Pattern Effect)
Pattern list
DMX
1
2
3
4
5
000-015
016-031
032-047
048-063
064-079
080-095
096-111
112-127
128-143
144-159
160-175
176-191

ENGLISH USER MANUAL
BRITEQ® 11/12 SPECTRA 3D LASER
192-207
208-223
224-239
240-255
DMX Channels Chart While ILDA is connected
CHANNEL
VALUE
DESCRIPTION
CH1
Grating
Rotation
000-004
No grating rotating
005-127
Clockwise grating rotating
128-133
No grating rotating
134-255
Anticlockwise grating rotating
CH2
Grating Effect
000-031
Laser 3D Effect
032-063
Scanned Beam Effect (Pattern Effect)
064-095
Laser Lumia Effect
096-127
Scanned Beam Effect (Pattern Effect)
128-159
Burst Grating Effect
160-191
Scanned Beam Effect (Pattern Effect)
192-223
Laser Universal Effect
224-255
Scanned Beam Effect (Pattern Effect)
#4 ILDA CONTROL:
This laser can be controlled by any PC equipped with ILDA compatible software + hardware. As soon as the
ILDA-input (17) of the laser is connected with an ILDA compatible controller, it will automatically switch to
ILDA control mode. From this moment on the laser will be completely controlled by the ILDA software: the
possibilities of the ILDA software will determine what you can do or not…
ILDA soft- and hardware are available from several independent suppliers. Some possible choices are:
- PHOENIX software (www.bocatec.de)
- PANGOLIN software (www.pangolin.com)
- And many other, up to you and your finances to see what is best for your needs …
MAINTENANCE
•Make sure the area below the installation place is free from unwanted persons during servicing.
•Switch off the unit, unplug the mains cable and wait until the unit has been cooled down.
During inspection the following points should be checked:
•All screws used for installing the device and any of its parts should be tightly fastened and may not be
corroded.
•Housings, fixations and installations spots (ceiling, truss, suspensions) should be totally free from any
deformation.
•When an optical lens is visibly damaged due to cracks or deep scratches, it must be replaced.
•The mains cables must be in impeccable condition and should be replaced immediately when even a small
problem is detected.
•In order to protect the device from overheat the cooling fans (if any) and ventilation openings should be
cleaned monthly.
•The interior of the device should be cleaned annually using a vacuum cleaner or air-jet.
•The cleaning of internal and external optical lenses and/or mirrors must be carried out periodically to optimize
light output. Cleaning frequency depends on the environment in which the fixture operates: damp, smoky or
particularly dirty surroundings can cause greater accumulation of dirt on the unit’s optics.
•Clean with a soft cloth using normal glass cleaning products.
•Always dry the parts carefully.
•Clean the external optics at least once every 30 days.

ENGLISH USER MANUAL
BRITEQ® 12/12 SPECTRA 3D LASER
•Clean the internal optics at least every 90 days.
Attention: We strongly recommend internal cleaning to be carried out by qualified personnel!
SPECIFICATIONS
This unit is radio-interference suppressed. This product meets the requirements of the current European and
national guidelines. Conformity has been established and the relevant statements and documents have been
deposited by the manufacturer.
Mains Input: AC 100~240V, 50/60Hz
Fuse: 250V 1.6A slow blow (20mm glass)
Total Power consumption: 40W
Sound Control: Internal microphone
DMX connections: 3pin XLR male / female
DMX channels: 1 or 19 channels
DMX starting address: 001 →494
Laser Power: 300mW Blue CW laser (λ= 450nm)
100mW Red CW laser (λ = 638nm)
80mW Green CW laser (λ = 505nm)
Laser radiation class: 3B
Beam diameter at aperture: 5 mm
Beam divergence: 2 mrad
MPE / NOHD: Not relevant, the beam is continuously scattered and
moves in all directions (no stationary laser beam)
Working temperature: 10°C to 40°C
Laser Safety Standard: EN60825-1: 2014
Size: see picture below
Weight: 4.5kg
Every information is subject to change without prior notice
You can download the latest version of this user manual on our website: www.beglec.com