Britex UREG User manual

MELBOURNE
Britex Place Mirra Crt
Bundoora VIC 3083
t(03) 9466 9000
e[email protected]om.au
SYDNEY
16 Northumberland Drv
Taren Point NSW 2229
t(02) 9531 2100
[e-mail]
PERTH
Unit 1/8 Principal Link
Malaga WA 6090
t(08) 9249 5464
[e-mail]
BRISBANE
19 Manilla St
East Brisbane QLD 4169
t(07) 3363 2400
e[email protected]om.au
ADELAIDE
The Britex Group
SA State Office
t1300 764 744
e[email protected]om.au
Installation
Guide
UREG
Regency
Urinal
UREG Installation Guide | QID 1.21 | Rev 3 | 29 May 2023
UREG
ISO
A3
SHEET 1 OF 3
SCALE:1:20
TITLE:
DO NOT SCALE DRAWING
DATE
UNLESS OTHERWISE SPECIFIED:
DIMENSIONS ARE IN MILLIMETERS
APPV'D
CHK'D
DRAWN
REVISION
Britex Metal Products Co. Pty Ltd.
ACN: 004 309 737
2 Mirra Ct, Bundoora Victoria 3083
P: 03 9466 9000 F: 03 9466 9044
britex.com.au [email protected]
Drawing:
AW
25/05/23
A
SD-2604.4

Australia’s Finest Stainless | britex.com.au
About
Preparation and Completion Notes
The BRITEX Regency Urinal is the most hygienic stainless-steel urinal in the BRITEX hinged
grate range. With the same extensive list of benefits as the Sanistep urinal, the Regency
features protecting side walls that may otherwise be exposed to water/fluid damage after
being installed for an extended period. The Regency is particularly suited to schools,
night clubs and public amenity buildings. WaterMark and WELS certified as required by
plumbing regulations and government legislation.
Britex urinals are approved for use as per the accompanying certifications and can be coupled with
cisterns, flush valves & sensor flushing systems according to specific model requirements. It is the
installer’s responsibility to ensure that the urinal is installed in accordance and to the regulations
of the residing governing authority and all applicable plumbing code regulations. Britex Floor
Mounted Urinal’s are fitted with a water spreader incorporating options of rear or top mounted
inlets (38mm (1.5”). As a standard practice 38mm (1.5”) inlets will be provided unless 25mm (1”)
inlets are specifically requested.
1. 38mm (1.5”) Inlets: Are typically supplied to urinals that are to be flushed with cisterns or flush
valves. The urinals inlet supply fitting consists of a nylon adaptor and flanged nut to suit 38mm
(1.5”) flush pipe tube, (copper, stainless steel etc). Alternatively, 40mm DWV PVC pipe can be
used by substituting the urinal nylon flange nut for a DWV PVC Adaptor Female Iron 40mm. If a
flushing devise is utilised with a smaller supply line, then the nylon inlet adaptor can be reduced
with appropriate fittings if the flushing device and supply requirements are in accordance with
the urinal specifications.
A Discharge waste outlet vary dependent on nominated size received on order placement,
but generally consist of 50mm (2’), 75mm (3’”) & 100mm (4”) dependent on local plumbing
regulations.
As the urinal is to be fixed to the rear wall, ensure that the substructure will provide sufficient
support to the urinal. Complete any reinforcement works as necessary and provide noggins where
required. Use appropriate anchors suitable for use with the substructure to fix the urinal to the wall
surface.
Floor mounted urinals can be recessed and made flush with the finished floor level or mounted
directly onto the floor (Step Up). If the urinal is to be recessed, refer to the urinal trench dimensions
within this document.
2
UREG Installation Guide | QID 1.21 | Rev 3 | 29 May 2023
WARNING
WHEN INSTALLATION IS COMPLETE, ENSURE THESE INSTRUCTIONS REMAIN INSIDE
THE PLASTIC BAG PROVIDED WITH THE UNIT FOR FUTURE REFERENCE
IMPORTANT
ALL SERVICE TO BE PERFORMED BY AN AUTHORISED SERVICE PERSON
Installation of this unit must be in accordance with AS/NZS 3500.2, the PCA and the local
regulatory requirements. Water and/or electrical supply conditions must comply to national or
state requirements and standards. Failure to comply shall void the product warranty and may
affect the performance of the product. For further support and after-sales care, please contact
Britex.

Australia’s Finest Stainless | britex.com.au
Preparation and Completion Notes
3
UREG Installation Guide | QID 1.21 | Rev 3 | 29 May 2023
The preparation of a slurry bed is part of the bedding down process for all urinal installations
inclusive of floor mounted and recessed urinals. Additional works, structural conformance, water
proofing etc. may be required to the substructure and should be investigated and approved by the
appropriate authorities. All preliminary works should be completed prior to the installation of the
urinal.
Protect the surface of the product during the installation process. Do not remove any PVC
coatings that may have been applied to the surface until the product has been commissioned and
ready to be used.
Recommended Flushing Devices
Rear Water Entry
Top
Water
Entry
FSM1 -
Smart
Saniflush
Sensor -
Electronic
FSM2 -
Smart
Saniflush
Sensor -
Electronic
FSF1 -
Saniflush
Sensor
- Elec-
tronic
FSF2 -
Saniflush
Sensor
- Elec-
tronic
FFV-E1
- Single
Piezo
Button
Electron-
ic Flush
Valve
FIW-
SP45 -
Pneumat-
ic In Wall
Cistern
Single
Push
Button
FCP
- Pull
Chain
Cistern
Urinal
Length
Single So-
lenoid Up
to 1800mm
Dual
Solenoid
- 1800mm-
3600mm
Single
Solenoid
1800mm
Dual So-
lenoid -
1800mm-
3600mm
Up to
1800mm
Up to
1800mm
Up to
1800mm
UREG

Australia’s Finest Stainless | britex.com.au
4
UREG Installation Guide | QID 1.21 | Rev 3 | 29 May 2023
UREG Drawing
As Required
200
Overall Height Varies According to Length
1120 50
1170 Shallow End
130 Minimum
220 Min - 485 Max
Stiffener
Ribbing
Waste and Cover
Fall to Waste 1:80 Minimum
610
40 40
408
Flush Entry Point
A Maximum of 2m per Water Entry is Recommended
Step on Grating
145
70 70 470
305 Standard
38mm Inlet
Assembly Fabricated
Full From Vitel Nylon
66 Compound
Full Length 25x65 Gal
C Channel Affixed
with Stud Fired to
Rear of Urinal
1.6mm SS Angle Legs
Spaced along Front
and Rear of Gutter
Tile Lip to
Rear and
Edges
UREG
Install Views
A3
SHEET 3 OF 3
SCALE:1:20
TITLE:
DO NOT SCALE DRAWING
DATE
UNLESS OTHERWISE SPECIFIED:
DIMENSIONS ARE IN MILLIMETERS
APPV'D
CHK'D
DRAWN
REVISION
Britex Metal Products Co. Pty Ltd.
ACN: 004 309 737
2 Mirra Ct, Bundoora Victoria 3083
P: 03 9466 9000 F: 03 9466 9044
britex.com.au [email protected]
Drawing:
AW
25/05/23
A
SD-2604.6
As Required
200
Overall Height Varies According to Length
1120 50
1170 Shallow End
130 Minimum
220 Min - 485 Max
Stiffener
Ribbing
Waste and Cover
Fall to Waste 1:80 Minimum
610
40 40
408
Flush Entry Point
A Maximum of 2m per Water Entry is Recommended
Step on Grating
145
70 70 470
305 Standard
38mm Inlet
Assembly Fabricated
Full From Vitel Nylon
66 Compound
Full Length 25x65 Gal
C Channel Affixed
with Stud Fired to
Rear of Urinal
1.6mm SS Angle Legs
Spaced along Front
and Rear of Gutter
Tile Lip to
Rear and
Edges
UREG
Install Views
A3
SHEET 3 OF 3
SCALE:1:20
TITLE:
DO NOT SCALE DRAWING
DATE
UNLESS OTHERWISE SPECIFIED:
DIMENSIONS ARE IN MILLIMETERS
APPV'D
CHK'D
DRAWN
REVISION
Britex Metal Products Co. Pty Ltd.
ACN: 004 309 737
2 Mirra Ct, Bundoora Victoria 3083
P: 03 9466 9000 F: 03 9466 9044
britex.com.au [email protected]
Drawing:
AW
25/05/23
A
SD-2604.6

Australia’s Finest Stainless | britex.com.au
Installation Instructions
1. Prior to installing the urinal ensure the substructure has been prepared to accommodate
all required services inclusive of supply lines, sanitary discharge connections and set down
trench for recessed urinals. Service locations are provided on the applicable model diagrams
within this document.
a. Rear inlet supply connections will require the provision of a permanent front or
rear access panel within the wall face to be provided above each inlet connection, or
alternatively, a temporary cavity that can be sealed on the completion of connections and
commissioning.
b. Sanitary discharge connections should be terminated at a height 20mm below the
underside of the urinal gutter. Terminating the discharge pipe with a pan collar fitted with
an internal rubber gasket is recommended.
2. On completion of the rough in process, place the urinal into position, ensuring the urinal
waste outlet spigot is in line and enters the discharge pipe without obstruction and the urinal
sits stable and flush to the rear wall.
3. Once in position and particularly with recessed urinal installations, preliminary checks and
adjustments should be carried out to ensure that the urinal is level and at the correct height.
a. Use the top of the urinal gutter’s front fascia edge to determine the level and height of
the urinal, taking into consideration and allowing for any final floor finishes, tiles etc.
b. Check and ensure that the horizontal top and side edges are level and that the front
vertical edges are plumb.
c. Use plastic packers under the feet or directly under the trough on USAN urinals to make
level or raise the urinal to the correct height. Do not use metal packers. Once satisfied that
the urinal is level, a container of water can be poured into the urinal gutter to ensure that it
adequately drains to the waste outlet.
4. Take note and mark any applicable reference points, then, remove the urinal from the set
position.
5. Mix a mortar or non-shrink grout slurry to a soft malleable consistency. The slurry mixture
should hold firm in a mound yet be pliable enough to spread throughout the underside
cavity of floor mounted urinals. For recessed urinals the slurry will be contained within the
trench cavity and can be of a softer consistency allowing it to overflow when the urinal is
placed into position.
6. Place the urinal back into position ensuring any packers used within the dry run are
correctly arranged and remain in location and that the waste outlet spigot is seated within
the discharge pipe.
a. It is critical to ensure that the slurry has not raised the base of the gutter or the formation
of the outlet that will prevent adequate draining.
b. Bed the urinal down to ensure it is seated correctly by applying even pressure to the
urinal. Even pressure can be applied to the urinals gutter, by standing on a length of timber
placed into the trough. Placing your foot on the outlet cover and applying pressure will also
ensure the outlet is correctly seated.
c. The urinal must be fully supported to alleviate any flexing. No air pockets should be
present.
d. Weighted timbers can be placed within the trough to maintain the formation of the
trough.
5
UREG Installation Guide | QID 1.21 | Rev 3 | 29 May 2023