Brivo T1bvt4d User manual

T1BVT4D

4 Door Kit with PTC Outputs

Fully assembled kit includes:

- Trove1 enclosure with TBV1 Altronix/Brivo backplane

- One (1) Tango1B - PoE Driven Power Supply with

Lithium Battery Backup

- One (1) ACMS8CB - Dual Input PTC Access Power Controller

T1BV34SD

4 Door Kit with PTC Outputs

Fully assembled kit includes:

- Trove1 enclosure with TBV1 Altronix/Brivo backplane

- One (1) AL600ULXB - Power Supply/Charger

- One (1) ACM4CB - PTC Access Power Controller

- One (1) VR6 - Voltage Regulator

T2BV78SD

8 Door Kit with PTC Outputs

Fully assembled kit includes:

- Trove2 enclosure with TBV2 Altronix/Brivo backplane

- One (1) AL1024ULXB2 - Power Supply/Charger

- One (1) ACMS8CB - Dual Input PTC Access Power Controller

- One (1) PDS8CB - Dual Input PTC Power Distribution Module

- One (1) VR6 - Voltage Regulator

T2BV778SD

8 Door Kit with PTC Outputs

Fully assembled kit includes:

- Trove2 enclosure with TBV2 Altronix/Brivo backplane

- Two (2) AL1024ULXB2 - Power Supply/Chargers

- One (1) ACMS8CB - Dual Input PTC Access Power Controller

- One (1) PDS8CB - Dual Input PTC Power Distribution Module

- Two (2) VR6 - Voltage Regulators

T3BV7716SD

16 Door Kit with PTC Outputs

Fully assembled kit includes:

- Trove3 enclosure with TBV3 Altronix/Brivo backplane

- Two (2) AL1024ULXB2 - Power Supply/Chargers

- Two (2) ACMS8CB - Dual Input PTC Access Power Controllers

- Two (2) PDS8CB - Dual Input PTC Power Distribution Modules

- Two (2) VR6 - Voltage Regulators

- One (1) RSB2 - Rocker Switch Bracket with

Two (2) Rocker Switches (Not evaluated by UL)

Rev. TBVKD_040323

Installing Company: _________________________ Service Rep. Name: __________________________________________

Address: _________________________________________________________ Phone #: _________________________

All registered trademarks are property of their respective owners.

Installation Guide

All components of these Trove kits are UL Listed sub-assemblies.

Please refer to the included corresponding Sub-Assembly Installation Guides for further information.

Access & Power Integration

- 2 - Trove Brivo PTC ULXB Kits Installation Guide

Overview:

Altronix/Brivo Trove kits are pre-assembled and consist of Trove enclosures/backplanes with factory installed Altronix power supply/chargers and

sub-assemblies. These kits also accommodate various combinations of Brivo boards for up to sixteen (16) doors in a single enclosure.

Configuration Chart:

Altronix

Model Number Input

Power

Supply

Board

Input

Fuse

Rating

Power

Supply

Board

Battery

Fuse

Rating

Maximum Supply

Current for Main Outputs

on Power Supply

board and ACM4CB/

ACMS8CB Access Power

Controllers’ outputs

Nominal

Output

Voltage

Range

(VDC)

Fail-Safe/

Fail-Secure

Dry Form

“C”

Outputs

Additional PTC

Protected Outputs

ACM4CB Board

Input Fuse Rating

ACM4CB Board

Output PTC Rating

ACMS8CB Board

Input PTC Rating

ACMS8CB Board

Output PTC Rating

PD8S8 Board

Input PTC Rating

PD8S8 Board

Output PTC Rating

T1BVT4D PoE

up to 90W N/A 10A/

32V

12VDC @ 5A

24VDC @ 3A

20.17-

26.4 8 – – – 9A 2.5A – –

T1BV34SD 115VAC 60Hz,

3.5A

5A/

250V N/A 24VDC @ 5.9A 20.17-

26.4 4 – 10A/

32V 2.5A – – – –

T2BV78SD 115VAC 60Hz,

4.2A

5A/

250V

15A/

32V 24VDC @ 9.4A 20.17-

26.4 8 8 – – 9A 2.5A 9A 2.5A

T2BV778SD 115VAC 60Hz,

8.8A

5A/

250V

15A/

32V

24VDC @ 9.4A

20.17-

26.4 8 8 – – 9A 2.5A 9A 2.5A

T3BV7716SD 115VAC 60Hz,

8.8A

5A/

250V

15A/

32V

24VDC @ 9.4A

20.17-

26.4 16 16 – – 9A 2.5A 9A 2.5A

9.7-

13.2

Installation Instructions:

Wiring methods shall be in accordance with the National Electrical Code/NFPA 70/ANSI, and with all local codes and authorities having jurisdiction.

Product is intended for indoor use only.

1. Remove backplane from enclosure. Do not discard hardware.

If your application requires a raised backplane, re-mount it using metal spacers and screws (provided).

2. Mark and predrill holes in the wall to line up with the top three keyholes in the enclosure. Install two/three upper fasteners and screws

in the wall with the screw heads protruding. Place the enclosure’s upper keyholes over the two/three upper screws; level and secure.

Mark the position of the lower two/three holes. Remove the enclosure. Drill the lower holes and install the fasteners. Place the

enclosure’s upper keyholes over the upper screws. Install the lower screws and make sure to tighten all screws.

3. Mount included UL Listed tamper switch(es) (Altronix Model TS112 or equivalent) in desired location, opposite hinge. Slide the

tamper switch bracket onto the edge of the enclosure approximately 2” from the right side (Fig. 1, pg. 2). Connect tamper switch wiring

to the Access Control Panel input or the appropriate UL Listed reporting device. To activate alarm signal open the door of the enclosure.

4. Mount Brivo boards to backplane, refer to pages 3-7.

5. Refer to the Power Supply/Charger Installation Guide (Tango1B, AL600ULXB, AL1024ULXB2) and

corresponding Sub-Assembly Installation Guide (ACM4CB, ACMS8CB, PDS8CB, VR6) for

further installation instructions.

Fig. 1

Tamper Switch

(included)

To Access Control Panel or

UL Listed Reporting Device

Edge of

Enclosure

Trove Brivo PTC ULXB Kits Installation Guide - 3 -

B B

Altronix Tango1B is mounted under ACMS8CB

PWR1 +

PWR2 +

COM -

PWR2 +

PWR1 +

+ PWR2 --

+ PWR1 --

Altronix ACMS8CB

Fig. 2 - T1BVT4D Congurations

T1BVT4D: Configuration of Brivo Controls Boards:

1. Align the Brivo board on the backplane to match the boards’ mounting holes with corresponding pems.

2. Fasten 4/40 - 5/8” Metal Spacers (provided) to pems that match the hole pattern for Brivo board (Fig. 2, 2a, pg. 3).

Note: Brivo board must be properly grounded.

Please use provided metal spacers for the lower right mounting holes (Fig. 2, pg. 3).

3. Mount Brivo board to spacers utilizing provided 4/40 - 5/16” Pan Head Screws (Fig. 2a, pg. 3).

4. Fasten backplane to Trove1 enclosure utilizing lock nuts (provided).

Access Controller Position Chart for the Following Models:

Brivo Access Controller Pem Mounting

ACS6000-MBE A

ACS6100-DB, ACS6100-IO B

Pem

4/40 - 5/8”

Spacer

Brivo board Backplane

4/40 - 5/16”

Pan Head Screw

Fig. 2a

Altronix ACMS8CB

Altronix Tango 1B is mounted under ACMS8CB

- 4 - Trove Brivo PTC ULXB Kits Installation Guide

B B

Altronix AL600ULXB

Altronix

ACM4CB

TRG

TRIGGER

INPUT

LED1 LED2 LED3 LED4

MAIN

OUTPUT 1

NC C NO COM NC C NO COM NC C NO COM NC C NO COM

OUTPUT 2 OUTPUT 3

IN GND

OUTPUT 4

-- +

CONTROL

-- +

POWER

+INP- T +RET-

INTERFACE

NO C NC

FACP

Altronix VR6 is mounted under ACM4(CB)

BAT FAIL NC C NO NC C NO AC FAIL

AC DC BAT

+BAT- + DC -

L G N

OFF - 24V

ON - 12V

To VR6 mounted under ACM4CB

12VDC

from VR6 output

Fig. 3 - T1BV34SD Congurations

T1BV34SD: Configuration of Brivo Controls Boards:

1. Align the Brivo board on the backplane to match the boards’ mounting holes with corresponding pems.

2. Fasten 4/40 - 5/8” Metal Spacers (provided) to pems that match the hole pattern for Brivo board (Fig. 3, 3a, pg. 4).

Note: Brivo board must be properly grounded.

Please use provided metal spacers for the lower right mounting holes (Fig. 3, pg. 4).

3. Mount Brivo board to spacers utilizing provided 4/40 - 5/16” Pan Head Screws (Fig. 3a, pg. 4).

4. Fasten backplane to Trove1 enclosure utilizing lock nuts (provided).

Access Controller Position Chart for the Following Models:

Brivo Access Controller Pem Mounting

ACS6000-MBE A

ACS6100-DB, ACS6100-IO B

Altronix AL600ULXB

Altronix VR6 is mounted under ACM4CB

To VR6 mounted under ACM4CB

Altronix

ACM4CB

Pem

4/40 - 5/8”

Spacer

Brivo board Backplane

4/40 - 5/16”

Pan Head Screw

Fig. 3a

Trove Brivo PTC ULXB Kits Installation Guide - 5 -

Fig. 4 - T2BV78SD Congurations

T2BV78SD: Configuration of Brivo Controls Boards:

1. Align the Brivo board on the backplane to match the boards’ mounting holes with corresponding pems.

2. Fasten 4/40 - 5/8” Metal Spacers (provided) to pems that match the hole pattern for Brivo board (Fig. 4, 4a, pg. 5).

Note: Brivo board must be properly grounded.

Please use provided metal spacers for the lower right mounting holes (Fig. 4, pg. 5).

3. Mount Brivo board to spacers utilizing provided 4/40 - 5/16” Pan Head Screws (Fig. 4a, pg. 5).

4. Fasten backplane to Trove2 enclosure utilizing lock nuts (provided).

Access Controller Position Chart for the Following Models:

Brivo Access Controller Pem Mounting

ACS6000-MBE A

ACS6100-DB, ACS6100-IO B

B B

Altronix VR6 is mounted under PDS8CB

+ INP1 --

PWR1 +OFF

IN1

IN2

PWR1 +

PWR2 +

COM (--- )

+ INP2 --

IN1 Fuse

Common Power Outputs (NEG)

OUT1 OUT2 OUT3 OUT4 OUT5 OUT6 OUT7 OUT8

1 2 3 4 5 6 7 8

Altronix PDS8(CB)

PWR1 +

PWR2 +

COM -

PWR2 +

PWR1 +

+ PWR2 --

+ PWR1 --

Altronix ACMS8(CB)

BAT FAIL

AC FAIL

- BAT + + DC -

AC DELAY

Altronix AL1024ULXB2

Altronix PDS8CB

Altronix ACMS8CB

Altronix VR6 is mounted under PDS8CB

Pem

4/40 - 5/8”

Spacer

Brivo board Backplane

4/40 - 5/16”

Pan Head Screw

Fig. 4a

- 6 - Trove Brivo PTC ULXB Kits Installation Guide

Fig. 5 - T2BV778SD Congurations

T2BV778SD: Configuration of Brivo Controls Boards:

1. Align the Brivo board on the backplane to match the boards’ mounting holes with corresponding pems.

2. Fasten 4/40 - 5/8” Metal Spacers (provided) to pems that match the hole pattern for Brivo board (Fig. 5, 5a, pg. 6).

Note: Brivo board must be properly grounded.

Please use provided metal spacers for the lower right mounting holes (Fig. 5, pg. 6).

3. Mount Brivo board to spacers utilizing provided 4/40 - 5/16” Pan Head Screws (Fig. 5a, pg. 6).

4. Fasten backplane to Trove2 enclosure utilizing lock nuts (provided).

Access Controller Position Chart for the Following Models:

Brivo Access Controller Pem Mounting

ACS6000-MBE A

ACS6100-DB, ACS6100-IO B

B B

Altronix VR6 is mounted under ACMS8CB

Altronix VR6 is mounted under PDS8CB

PWR1 +

PWR2 +

COM -

PWR2 +

PWR1 +

+ PWR2 --

+ PWR1 --

Altronix ACMS8(CB)

+ INP1 --

PWR1 +OFF

IN1

IN2

PWR1 +

PWR2 +

COM (--- )

+ INP2 --

IN1 Fuse

Common Power Outputs (NEG)

OUT1 OUT2 OUT3 OUT4 OUT5 OUT6 OUT7 OUT8

1 2 3 4 5 6 7 8

Altronix PDS8(CB)

BAT FAIL

AC FAIL

- BAT + + DC -

AC DELAY

Altronix AL1024ULXB2

BAT FAIL

AC FAIL

- BAT + + DC -

AC DELAY

Altronix AL1024ULXB2

Altronix AL1024ULXB2 Altronix AL1024ULXB2

Altronix PDS8CB

Altronix ACMS8CB

Altronix VR6 is mounted under PDS8CB

Altronix VR6 is mounted under ACMS8CB

Pem

4/40 - 5/8”

Spacer

Brivo board Backplane

4/40 - 5/16”

Pan Head Screw

Fig. 5a

Trove Brivo PTC ULXB Kits Installation Guide - 7 -

Fig. 6 - T3BV7716DS Congurations

T3BV7716SD: Configuration of Brivo Controls Boards:

1. Align the Brivo board on the backplane to match the boards’ mounting holes with corresponding pems.

2. Fasten 4/40 - 5/8” Metal Spacers (provided) to pems that match the hole pattern for Brivo board (Fig. 6, 6a, pg. 7).

Note: Brivo board must be properly grounded.

Please use provided metal spacers for the lower right mounting holes (Fig. 6, pg. 7).

3. Mount Brivo board to spacers utilizing provided 4/40 - 5/16” Pan Head Screws (Fig. 6a, pg. 7).

4. Fasten backplane to Trove3 enclosure utilizing lock nuts (provided).

Access Controller Position Chart for the Following Models:

Brivo Access Controller Pem Mounting

ACS6000-MBE A

ACS6100-DB, ACS6100-IO B

B B B

+ INP1 --

PWR1 +OFF

IN1

IN2

PWR1 +

PWR2 +

COM (--- )

+ INP2 --

IN1 Fuse

Common Power Outputs (NEG)

OUT1 OUT2 OUT3 OUT4 OUT5 OUT6 OUT7 OUT8

1 2 3 4 5 6 7 8

Altronix

PDS8(CB)

+ INP1 --

PWR1 +OFF

IN1

IN2

PWR1 +

PWR2 +

COM (--- )

+ INP2 --

IN1 Fuse

Common Power Outputs (NEG)

OUT1 OUT2 OUT3 OUT4 OUT5 OUT6 OUT7 OUT8

1 2 3 4 5 6 7 8

Altronix

PDS8(CB)

Altronix VR6 is mounted under ACMS8CB

PWR1 +

PWR2 +

COM -

PWR2 +

PWR1 +

+ PWR2 --

+ PWR1 --

Altronix ACMS8(CB)

Altronix VR6 is mounted under ACMS8CB

PWR1 +

PWR2 +

COM -

PWR2 +

PWR1 +

+ PWR2 --

+ PWR1 --

Altronix ACMS8(CB)

BAT FAIL

AC FAIL

- BAT + + DC -

AC DELAY

Altronix AL1024ULXB2

BAT FAIL

AC FAIL

- BAT + + DC -

AC DELAY

Altronix AL1024ULXB2

RSB2

Altronix AL1024ULXB2

Altronix ACMSCB8

Altronix PDS8CB

Altronix ACMS8CB

Altronix VR6 is mounted under ACMS8CB

Pem

4/40 - 5/8”

Spacer

Brivo board Backplane

4/40 - 5/16”

Pan Head Screw

Fig. 6a

Altronix PDS8CB

- 8 - Trove Brivo PTC ULXB Kits Installation Guide

T1BVT4D and T1BV34SD (Trove1) Enclosure Dimensions (H x W x D approximate):

18” x 14.5” x 4.625” (457mm x 368mm x 118mm)

4.5” (114.3mm) 4.5” (114.3mm) 2.75”

(69.9mm)

1.115” (28.3mm)

1.36” (34.5mm)

1.25” (31.8mm) 1.25” (31.8mm)

1.5” (38.1mm)

8.5” (215.9mm)6.5” (165.1mm)

1.5” (38.1mm)

8.5” (215.9mm)6.5” (165.1mm)

4.5” (114.3mm)

13.0” (330.2mm)

0.6” (15.2mm)

14.5” (321.3mm)

1.45” (36.8mm)

7.25” (184.2mm)

1.95” (49.5mm)

1.1” (27.9mm)

0.6” (15.2mm)

0.57” (14.5mm)

18.0” (457.2mm)

1.25” (31.8mm)

- 9 - Trove Brivo PTC ULXB Kits Installation Guide

T2BV78SD and T2BV778SD (Trove2) Enclosure Dimensions (H x W x D approximate):

27.25” x 21.5” x 6.5” (692.2mm x 552.5mm x 165.1mm)

6.75” (171.5mm)8.25” (209.5mm)

8.00” (203.2mm)

2.00” (50.8mm)

1.25” (31.8mm)

5.25” (133.4mm) 5.25” (133.4mm)7.00” (177.8mm)

1.25” (31.8mm)

6.25” (158.8mm) 19.80” (502.9mm)

1.00” (25.4mm)

27” (685.8mm)

1.5”

(38.1mm)

2.00” (50.8mm) 2.00” (50.8mm)

3.5”(88.9mm) 3.5”(88.9mm)

21.50” (546.1mm)

5.25” (133.35mm) 5.25” (133.35mm)

6.25” (158.8mm)

1.25”

(31.8mm)

0.85” (21.6mm)

0.5625” (14.3mm)

2.415” (61.3mm)

0.685” (17.4mm)

1.77”

(45mm)

0.885” (22.5mm)

1.125” (28.3mm)

Knockouts

2.00” (50.8mm) 2.00” (50.8mm)

- 10 - Trove Brivo PTC ULXB Kits Installation Guide

T3BV7716SD (Trove3) Enclosure Dimensions (H x W x D approximate):

36.12” x 30.125” x 7.06” (917.5mm x 768.1mm x 179.3mm)

2”

(50.8mm)

8.75” (222.3mm) 8.75” (222.3mm)

8.62” (219mm)

7.06” (179.3mm)

1.25” (31.8mm)

2.00” (50.8mm) 7.12” (222.3mm) 9.5” (241.3mm) 9.5” (241.3mm)

30.12” (768.1mm)

14.01” (355.9mm) 14.01” (355.9mm)

1.25” (31.8mm) 1.55” (39.4mm)

1.78” (45.2mm)

1.25” (31.8mm)

1.07”

(27.2mm)

1.10” (27.9mm)

2” (50.8mm)

10.75” (273.1mm)10.75” (273.1mm) 10.62” (269.8mm)

2.00” (50.8mm)10.75” (273.1mm)10.75” (273.1mm) 10.62” (269.8mm)

36.12” (917.5mm)

33.63” (854.2mm)

2” Conduit

3/4” Conduit

1” Conduit

3/4” Conduit

1” Conduit

1.5” Conduit

1.25” Conduit 1.5” Conduit

1.25” Conduit

3/4” Conduit

1” Conduit

3/4” Conduit

1” Conduit

- 11 - Trove Brivo PTC ULXB Kits Installation Guide

Notes:

- 12 - Trove Brivo PTC ULXB Kits Installation Guide

Notes:

Brivo Inc. is not responsible for any typographical errors.

–––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––

7700 Old Georgetown Rd #300 | Bethesda, MD 20814 USA

phone: +1 866.692.7486 | email: [email protected] | www.brivo.com

IITrove Brivo PTC (ULXB) Kits D03W

Other manuals for T1BVT4D

This manual suits for next models

Table of contents