Briza Air Cooler User manual

USER MANUAL

2CONTENTS
Caution
Operating Guide
Components
Operation Instruction
Cleaning & Maintenance
Troubleshooting
Technical Information
3
3
4
6
7
10
12

3
CAUTION
OPERATION GUIDE
1. This unit is controlled with a touchscreen panel.
2. Please use this unit with adequate air ventilation.
3. Do not exceed “max” water level marker when
lling the tank. Do not run the cooling function
if water level is to low.
4. Drain the water tank when cleaning the unit.
5. Fill tank with water only. Do not add any
chemicals.
6. Make sure your power supply is 120 V / 60 Hz.
The unit will not operate normally if power supply
is too low. Damage may occur if the power is too
high.
7. Unplug the unit from power supply when not
in use.
8. Please note that when the tank is empty the unit
will switch from “Cool” to “Fan” mode. Leave the
unit in “Fan” mode for 30-40 minutes after use to
dry the lters.
1. When moving the unit, use caution not to spill
water from the tank.
2. Don’t put anything on top of the unit.
3. Don’t put anything directly in front of the unit.
4. Don’t put anything through the front grill.
5. Unplug the unit before lling with water or
cleaning.
6. Stop operating this unit immediately if it
functions abnormally. Contact
[e-mail] for further instruction.
7. To reduce the risk of re or electric shock, do not
use this fan with any solid-state speed control
device.
8. Do not operate any fan with a damaged cord or
plug.
9. Do not run cord under carpeting. Do not cover
cord with throw rugs, runners or similar coverings.
Do not route cord under furniture or appliances.
Arrange cord away from trafc area and where it
will not be tripped over.
IMPORTANT: You must unscrew the tank base and remove the plate-sized plastic piece prior to rst use.

4COMPONENTS
62.5 cm
Handles
FRONT SIDE TOP
Vent
Screw
Side Panel
Water Tank
Tank Cover
Control Panel
Water Level Scale
31 cm

5
COMPONENTS
CONTROL PANEL REMOTE CONTROL
Power ON/OFF
Wind Speed
Cooling
Swing
Wind Speed
Swing
Cooling
Power ON/OFF
power
speed
cool
swing

6OPERATING INSTRUCTION
Open the tank
cover by pulling up
and out from here
Filling Water Tank
Open the tank cover on the back of the unit as
shown in the illustration below. Filll the tank with 8
L of water. Use the visual indicator on the front or
for reference insert your nger into the tank: if you
touch water then it is full.
Power
Press “Power” on the control panel or remote to turn
the fan on. “Power” will illuminate, press again to
power off.
Speed
Press “Speed” on the control panel or remote to
control wind speed. Speeds: Low (1), medium (2),
High (3), selected speed will light up.
Swing
Press “Swing” on the control panel or remote to have
the front grill oscillate. “Swing” will illuminate. Press
again to stop “Swing” mode.
Cool
Press “Cool” on the control panel or remote to
operate cooling function. Light will illuminate.
Press again to switch off.
NOTE
When the “Cool” mode is activated, the water will be pumped up to saturate the lters. Water owing through the lters
mixes with the incoming air in turn, lowering the temperature. The effectiveness depends on humidity and ambient
temperature when the unit is in “Cool” mode. Puried/distilled water is recomended, regular cleaning is required.

7
CLEANING & MAINTENANCE
Cleaning the Unit Body
Use a 10:1 water and vinegar mixture and a soft towel.
Cleaning the Water Tank
Remove the 4 screws from the bottom of the water tank and clean the tank base with a soft, non abrasive
towel with the water and vinegar mix.
IMPORTANT: Always unplug the fan before cleaning, disassembling or servicing.

8
Cleaning the Filters
Once a week (recommended), open the rear tank cover and slide the side panels as shown in the illustration
below.
Open the tank
cover from here
Remove lters, soak in vinegar-water (1:4 ratio) for 10-15 minutes. Let dry and wipe with soft cloth.
CLEANING & MAINTENANCE

9
CLEANING & MAINTENANCE
When putting the unit back together make sure to line up the markings on the side panels before you rotate
them back into place. To put the rear panel back on, rst placeing the bottom of the panel in before locking
the top into place.

10 TROUBLESHOOTING
PROBLEM POSSIBLE CAUSE CORRECTION
The remote control is not working. 1. Remote control batteries have run out. 1. Replace batteries.
The unit is making a clicking noise. 1. Loose pump parts or vents. 1. Make sure all pump parts and vent
horizontal slats are securely in place.
The unit is making a gurgling noise. 1. The unit is out of water. 1. Rell the water tank (see page 6).
The pump is not functioning properly /
no cool air is circulating.
1. The lters are clogged or dirty.
2. The pump has become dislodged or
clogged.
3. Excessively high relative humidity.
1. Clean or replace the lters.
2. Make sure the pump is fully intact and
fully submerged in water.
3. When the unit is used for long periods
of time, the relative room humidity will
increase, to counteract the humidity
and allow more ventilation in the
room, we suggest opening a window.