BroadcastVision FITNESS CINEMA User manual

FITNESS GINEMA RECEIVER
Operations Manual
5126 Glareton Drive #160
Agoura Hills, Galifornia 9130i
Ph (El8) E79-9780 Fx (S18) BZ9-9290
www.broadcas tvis ion.com

TECHNICAL ASSISTANCE
For Technical Assistance
Telephone (818) 87e-9780
(800) 770-977O
(818) 879-97e0
Fax
Or write to:
BROADCASTVISION TM
5126 Clareton Drive #160
Agoura Hills, California 91301
Support hours are from 9:00AM - 5:00PM PST
- NOTICE r
Due to the advancement in technology, BRoRocASTVtSloNrM reseryes the right to make
changes in specifications, hardware.,,rurt:lt;;i:l:"t accompanying documentation
BRoaocestVtstoNrM is a registered tradernark
Rev 10/06/99
@f 999 BRoADCASTVISIoN LLC, all rights resened

MOUNTING FITNESS CINEMA CARDIO RECEIVERS
re Ties
The Fitness Cinema Receiver is designed to attach easily to any vertical or horizontal
bar on most cardio equipment.
r Begin by inserting two nylon wire ties through the mounting bracket on the back of
the Fitness Cinema Receiver.
' Wrap wire ties around the bar and pull until the ties are completely tight and secure
so that it does not rotate.
. Make sure not to interfere with any equipment displays or control panels.
Note: ln the event that the equipment has no available bars or hand rails, the Fitness
Cinema Receiver mounting bracket can be easily removed with pliers and can be
attached with heavy-duty double-stick tape or super-lock velcro io any flat surface.

CONNECTING POWER TO FITNESS CINEMA RECEIVERS
I
I
\
Pins 1-4
Unused
Pin 5 GND
Pin 6 V+
C-Safe Po$/er Supply
Cable Detail
From C-Safe port or
AC adaptor C-Safe Power Supply
Connection Detail
lmportant: Many leading brands of cardiovascular equipment are Fitness Cinema
ready. Contact BRoAoCRSTVISION for a list of these manufacturers.
To connect Fitness Cinema Receivers to Fitness Cinema ready equipment, simply
connect the supplied connector cable from the back of the Fitness Cinema Receiver to
the C-Safe port on the cardio equipment.
For cardio equipment that does not have the C-Safe Fitness Cinema port, connect the
supplied AC adaptor to a 1 10VAC (1 10V wall type outlet) outlet.

FCR FRONT PANEL LAYOUT
I ]P )<rr DlspLAy
I Jb
\
-/
r
l:
^**^ I i
(17) (A)++- voLUME uP & DowN
-uo.*E- I i
CTIANI.EL
FT?NESS
\\-- HEADPH'NE JACK
The DISPLAY shows channel number and programming numbers
The CHANNEL SELEGT buttons toggle the channels up or down
The VOLUME UP & DOWN buttons raise or lower headphone volume
HEADPHONE JACK
a
o
C, NEMA

PROGRAMMING BANKS
INCREASE BANK #
DECREASE BANK #
DISPLAY
INCREASE MAX #
CHANNELS IN BANK
li
I i ?ECRE4SF MY t
4\, | | Utrt r(trl{Dtr lvlfv\ tf
.A,)€--I-F CHANNELS IN BANK
/'-1\
i\7) (l-r)
\!-/ \--,/
CHA}'IIEL
FTTNESS
1. Unplug power ja.ck to shut down power.
2. Depress and hold in the "VOLUME DOWN" button (lower left button on panel).
3. Reinsert power into jack while holding "VOLUME DOWN" button.
The display screen will display the bank number on the left and the channel number on
the right side.
The transmitter consists of 4 banks with 8 channels. The factory default setting is: Bank
1 with 8 channels and Bank s 2 through 4 with 0 channels. To program the banks,
select the Bank by using the buttons on the left side of the panel ( see diagram) and
then select the total number of channels to be used in that bank using the buttons on
the right. Set up each bank with the total number of channels needed in that bank.
For example:
. lf you are using 8 transmitters, set bank 1 to 8 channels and banks 2, 3, and 4
to 0 channels.
. lf you are using 12 transmitters, set bank 1 to 8 channels, bank 2lo 4
channels, and banks 3 and 4 to 0 channels.
Sefting the channel number to 0 for a bank turns off that banR and that bank is not used.
To exit the bank programming mode, hold in the "CHANNEL DowN" first, then hold
"VOLUME DOWN" button together (the two lower buttons on the front panel). The
display will flash the programmed settings and then will return to the operating rnode.
[-]F-l
C I NEMA
To enter programming mode:

SPECIFICATIONS
Operating Frequency,
Max Channels
O'l 'l l\ILlz la Q27l|.tU-
32
Banks 4
RF lnput Sensitivity
Channel Separation MpX
1.21tV
30dB
Audio
Frequency Response
THD SAHzto 10kHz -3dB
.3%
Audio Output 100mW
Power Supply
Minimum lnput 6VDC
Maximun lnput 1 TVDC
100mA
Supply Current