Broadcom 9460-16i User manual

Thank you for purchasing the
Broadcom PCIe Storage Adapter.
Please take a few minutes to read
this quick installation guide before
you install the adapter.
ATTENTION: Perform all installation work at
an electrostatic discharge (ESD)-
safe workstation that meets the
requirements of EIA-625,
Requirements for Handling
Electrostatic Discharge Sensitive
Devices. You must perform all
actions in accordance to the
latest revision of the IPC-A-610
ESD-recommended practices.
Getting Started Guide
Broadcom PCIe Storage Adapter
5972-4867-P0
Hardware Installation Instructions
CAUTION: Disconnect the computer from the power supply and from any networks to which you
will install the adapter, or you risk damaging the system or experiencing electrical
shock.
ATTENTION: To avoid the risk of data loss, back up your data before you change your system
configuration.
To install the Broadcom PCIe storage adapter, follow these steps.
1. Unpack the adapter, and inspect it for damage. Unpack the adapter in a static-free environment.
Remove the adapter from the anti-static bag, and carefully inspect the device for damage. If you notice
any damage, contact Broadcom or your reseller sales and support representative.
2. Prepare the computer. Turn off the computer, and disconnect the power cord from the rear of the
power supply. Remove the cover from the chassis.
3. Insert the adapter into an available PCIe slot. Locate an empty PCIe slot adequate for your
board. Align the adapter to a PCIe slot. Press down gently, but firmly, to seat the adapter correctly in the
slot.
4. Connect the appropriate cables between the adapter and the backplane or storage devices.
CAUTION: For NVMe connections to a SFF-8639 (U.2) bayRUFRQQHFWLRQVWRD3&,HVZLWFKuseRQO\
DSSURYHGFDEOHVZLWK5()&/.Iorwarded on the proper pins. Improperly connecting a
VWDQGDUG*6$6FDEOHWRDSFF-8639 bay could damage the PCIe stRUDge adapter and
WKHGULYH5HIHUWRWKHDGDSWHUQuick Installation Guide and the cable configurations
FKDSWHULQWKHuser guide for more information on connecting to NVMe drives.
5. Make sure the system provides the required airflow for the adapter.
Complete installation instructions, including instructions on how to change the bracket, can be found at
this address: https://www.broadcom.com/support/download-search. Refer to the Quick Installation
Guide and the User Guide.
Driver Installation
The firmware and drivers are routinely updated and made available on the Support and Download
center. Please visit https://www.broadcom.com/support/download-search and download the latest
firmware and driver for the adapter.
PCIe Adapter Airflow Inlet Temperature
9460-16i 250 LFM 55°C
9460-8i 250 LFM 55°C
9480-8i8e 250 LFM 55°C
9440-8i 200 LFM 55°C
9400-16i 200 LFM 55°C
9400-8i 200 LFM 55°C
9400-16e 200 LFM 55°C
9400-8e 200 LFM 55°C

TECHNICAL SUPPORT
For assistance installing, configuring, or running
the adapter, contact Broadcom Technical
Support:
WARRANTY NOTICE
1. The warranty does not cover the return of
parts damaged by changing the bracket.
2. The warranty does not cover ESD damage to
the adapter. Adapters returned without a bracket
mounted on the board will be returned without
return merchandise authorization (RMA)
processing.
Website: www.broadcom.com
For product information and a complete list of distributors, please go to our website: www.broadcom.com.
Broadcom, the pulse logo, Connecting everything, Avago Technologies, and the A logo are the trademarks of Broadcom in
the United States, certain other countries and/or the EU.
Copyright © 2017Broadcom. All Rights Reserved. pub-005789.
The term "Broadcom" refers to Broadcom Limited and/or its subsidiaries. For more information, please visit
www.broadcom.com. Broadcom reserves the right to make changes without further notice to any products or data herein
to improve reliability, function, or design.
Information furnished by Broadcom is believed to be accurate and reliable. However, Broadcom does not assume any
liability arising out of the application or use of this information, nor the application or use of any product or circuit described
herein, neither does it convey any license under its patent rights nor the rights of others.
5972-4867-P0
January 20, 2017.
Handling Instructions
The handling and usage instructions stated herein are general guidelines for board-level products.
Individual board-level products may have additional instructions and requirements in the applicable
product specification, which should be consulted.
• Complete all handling at an electrostatic discharge (ESD)-safe workstation with ESD-safe tools. The
workstation and tools must comply with IPC-A-610 at a minimum or ANSI/ESD S20.20.
• Handle by the edges of the base board. Do not handle the board by the bracket, heat sinks, or any
installed daughter board or DIMM memory.
• Do not stack boards after removing them from their shipping containers. Place boards on a flat, ESD-
safe surface with the top side of the board up to prevent damage to the heat sink.
• Do not bend or twist the board at any time. Any stress that exceeds 500 micro-strain, or 500 micro-
inches of deflection per inch of board material in any direction, could damage the board. Broadcom
follows the IPC/JEDEC-9704 industry standard.
• When installing the board in a system, press down evenly on the top corners of the base board to
avoid contact with brackets, heat sinks, or any installed daughter board or DIMM memory.
• When installing cables, align the cable with the board-mounted connector. Do not force the cable
into the connector, and orient any polarized cables properly.
• Refer to the board Quick Installation Guide for complete instructions on changing the bracket,
including screw torque specifications.
• Disconnect the power before removing or replacing the board.
• Do not allow any fluid or any material that is conductive or corrosive to contact the board.
• The boards are designed to operate in an ambient environment of 10 °C to 55 °C (dry bulb). The
relative humidity environment should be between 20% and 80% (non-condensing).
• To avoid overheating, make sure the minimum required airflow is applied. Refer to the board Quick
Installation Guide for more information.