Broan ALLURE QS2 Series User manual

ALLURE® QS2 SERIES
RANGEH
000
ALLURE®
QS2 SERIES RANGE HOOD
READ AND SAVETHESE INSTRUCTIONS
A FOR DOMESTIC COOKING ONLY A
Page 1
Patent No.:
US D450, 829 S
WARNING 4. A
TO REDUCETHE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY
TO PERSONS, OBSERVE THE FOLLOWING:
1. Use this unit only in the manner intended by the manufacturer. If
you have questions, contact the manufacturer at the address or
telephone number listed
in the warranty.
2. Before servicing orcleaning unit, switch power off at service panel
and lock the service disconnecting means to prevent power from
being switched
on accidentally. When the service disconnecting
means cannot
be locked, securely fasten a prominent warning
device, such
as a tag, to the service panel.
3. Installation work and electrical wiring must be done by a qualified
person(s)
in accordance with all applicable codes and standards,
including fire-rated construction codes
and standards.
4. Sufficient air is needed for proper combustion and exhausting of
gases through
the flue (chimney) of fuel burning equipment to
prevent backdrafting. Followthe heating equipment manufacturer's
guideline
and safety standards such as those published by the
National
Fire Protection Association (NFPA), and the American
Society of Heating, Refrigeration
and Air Conditioning Engineers
(ASH RAE), and the local code authorities.
5. When cutting ordrilling into wall or ceiling, do not damage electrical
wiring
and other hidden utilities.
6. To reduce the risk of fire or electric shock, do not use this range
hood with an additional speed control device.
7. Ducted fans must always be vented to the outdoors.
8. To reduce the risk of fire, use only metal ductwork.
9. Use with approved cord-connection kit only.
10. This unit must be grounded.
TO REDUCE THE RISK OF A RANGE TOP GREASE FIRE:
t Never leave surface units unattended at high settings. Boilovers
cause smoking
and greasy spillovers that may ignite. Heat oils
slowly
on low or medium settings.
2. Always turn hood ON when cooking at high heat or when cooking
flaming foods.
3. Clean ventilating fans frequently. Grease should not be allowed to
accumulate on
fan or filter.
4. Use proper pan size. Always use cookware appropriateforthe size
of the surface element.
TO REDUCE THE RISK OF INJURY TO PERSONS IN THE EVENT
OF A RANGE TOP GREASE FIRE, OBSERVETHE FOLLOWING:*
1. SMOTHER FLAMES with aclose-fitting lid, cookie sheet, ormetal
tray, then turn off the burner. BE CAREFUL TO PREVENT BURNS.
If the flames do not go out immediately, EVACUATE AND CALL
THE FIRE DEPARTMENT.
2. NEVER PICK UP A FLAMING PAN - You may be burned.
3. DO NOT USE WATER, including wet dishcloths or towels -violent
steam explosion will result.
4. Use an extinguisher ONLY if:
A. You know you have aClass ABC extinguisherand you already
know how to operate
it.
B. The fire is small and contained in the area where it started.
C. The fire department is being called.
D. You can fight the fire with your back to an exit.
* Based on "Kitchen Fire Safety Tips" published by NFPA.
CAUTION A
~~~~~~==~--------------------
1. For indoor use only.
2. For general ventilating use only. Do not use to exhaust hazard-
ous or explosive materials
and vapors.
3. To avoid motor bearing damage and noisy and/or unbalanced
impellers,
keep drywall spray, construction dust, etc. off power
unit.
4. For best capture of cooking impurities, your range hood should
be mounted so that the top of the hood is 24-30" above the
cooking
surface.
5. Please read specification label on productforfurther information
and requirements.
Installer: Leave this manual with
the homeowner.
Homeowner: Operating and
Cleaning information on page
6.
I NOTE I If
hood is to be installed Non-Ducted:
Purchase a set of (2) non-ducted filters from your
local distributor or retailer and attach them to the
aluminum
mesh filters.
TABLE OF CONTENTS
This manual is divided into sections as follows:
"PREPARE HOOD LOCATION"
Run ductwork from roof or wall cap, and electrical wiring from
service panel - to installation location
"PREPARETHE HOOD"
Get your hood
ready for installation
"CONNECTWIRING"
Make electrical wiring connections to hood
"INSTALL HOOD"
Secure
hood to cabinet and ductwork -install bulbs and filters
"OPERATION"
How to use the hood controls
"CLEANING"
Keep your hood in top working condition
"SERVICE PARTS"
Part numbers and exploded view of hood components
"WARRANTY"
One-year limited warranty and how to contact
us
Register your product online at: www.broan.ca/register

ALLURE® QS2 SERIES
RANGEH
000
Page 2
PREPARE HOOD LOCATION PREPARE
THE HOOD
311.i" X 10" DUCT
(For horizontal discharge)
Determine whether hood will discharge vertically (3%" x 10").
or horizontally (3%" x 10" only). For vertical or horizontal dis-
charge, run ductwork between the hood location and a roof
cap
or wall cap. For best results, use a minimum number of
transitons and elbows.
Use diagrams, below, for proper placement of ductwork and
electrical cutout in cabinet
or wall. For a non-ducted installa-
tion, DO NOT cut a duct access hole.
1615/16" (36" hood)
19
15/16"
(42" hood)
~
)'II
~
Id
\il)i
~
'= -W:'''
WOOD SHIMS
(recessed-bottom
cabinets only)
3'\4" X 10"
HOOD MOUNTING SCREWS (4) VERTICAL DUCT
1315/16" (30' hood)
CABINET FRONT
~~';~~~="~l~====t=====~i::~~
t
CENTER
LINE
3'\4" X 10"
(recessed-bottom HORIZONTAL DUCTING
cabinets only) CABINET FRONT
," )
WOOD SHIMS
II
l \----c-L~r~-~
3%" T,'
CABINET .!. L-"';';;;;~~;::;"~
BOTTOM 1_ 5%" 5%:...1
1315 116" (30" hood) 1;'~"" (30"h d)
15 16
1915, "(42" h d) 16 /16 (36 hood)
~
1615/16" (36" hood) "" 00
16 00 t 19
15
/16" (42" hood)
HOOD
MOUNTING CENTER ELECTRICAL
SCREWS (4) LINE ACCESS HOLE
(in wall)
I]] Run house wiring between service panel and hood location.
Remove tape holding
Filters in place. Pull down on filter
tabs
or finger holes and lift filters out. Set filters aside.
TEFLON®-
COATED
BOTTOM
COVER
(Held in
place with
2 screws)
I]] Remove [email protected]:oated bottom cover from hood. Set
cover and mounting screws aside.
Teflon' is a registered trademark of DuPont.
DAMPER!
DUCT
CONNECTOR
Remove
DamperlDuct Connector from inside thehood.
Set connector aside -with mounting screws and parts bag.

ALLURE® QS2 SERIES
RANGEH
000
Page 3
PREPARETHE HOOD PREPARE
THE HOOD
Remove either top or back wiring knockout and install ap-
proved Electrical Cable Clamp.
Ducted Installation -Skip to Step 11.
The following Steps (5 thru 10) are for
NON-DUCTED INSTALLATION ONLY.
(3) #8 SCREWS
LIGHT
PANEL
I]) Remove Light Panel -held in place with (3) #8 screws
and (2) #8 screws. Disconnect light assembly wire harness
(white connector).
Remove Air
Chute -held in
place with one
(1) screw.
NOTE: Be care-
ful not to discon-
nect any wires.
Remove
Baffle
from air chute.
Tabs will disen-
gage
from
Slots.
SUPPORT FIN
Rotate baffle. Reinsert
baffle into airchute (as
shown) so that baffle fits
all the way into
into airchute. An audible
"click" will
be heard when
fully installed.
This will direct
air flow through
the non-ducted
slots on top
of hood.
Re-install airchute and screw,
re-connect wire harness, and replace light panel.
NOTE: Be careful not to trap wires between
Support Fin
and light panel.

ALLURE® QS2 SERIES
RANGEH
000
PREPARE THE HOOD
!ill Non-Ducted Installations Only: Require a Performance Ring
to be attached to the blower wheel.
To install ring:
1. Remove the BlowerWheel by rocking it side to side and
applying a slight force to pull wheel from motor. Remove _
Retaining Ring if necessary.
2. Slide the ring onto the Small DiameterEndofthe wheel
and
down to the Stop Edge of the wheel.
3. Reassemble wheel to motor. Make sure Tab on wheel fits
into one of the Motor Slots. -
4. Push wheel down until it is locked in place.
5. Check that wheel is properly positioned as shown. Press
Sections into place if necessary. Make sure wheel turns
freely.
TOP RECTANGULAR
DUCT KNOCKOUT
(Remove for3 j4"x 10"
Vertical
REAR
RECTANGULAR
DUCT KNOCKOUT
(Remove for 3W'x 10"
Horizontal Discharge)
!ill Remove appropriate Duct Knockout(s) from top or back of
hood.
Page 4
PREPARETHEHOOD
TIES
,l
",'.
METAL STRIP
PLATE
Horizontal Discharge Only: Remove the Plate in front of the
horizontal discharge
knockout. Cut the Ties, lift plate out,
and discard plate. DO NOT REMOVE the Metal Strip held
in place with two Screws.
TOP/BACK
UP TO 1"
EDGE
SIDE-TO-SIDE
ADJUSTMENT
DAMPER!
PIVOT
DUCT
CONNECTOR
(Vertical
discharge
position shown)
314" x 10" Dueled Discharge Only: Remove Tape from damper
flap and attach DamperlDuct Connector over knockout
opening with screws
removed in Slep 4 under "PREPARE
THE HOOD': Make suredamperPivot is nearesttoTop/Back
~ofhood.
I NOTE I Damper/Duel Connector can be installed up to 1-inch
on either side ofhood center - to accomodate off-center
ductwork.
In extreme off-center installations, one end of
the duct connector
may need to betrimmed to clear the
electrical cable clamp.

ALLURE® QS2 SERIES
RANGEHOOD
CONNECTWIRING
A WARNING: To reduce the risk of electric shock,
.a make sure power is switched off at the service
panel. Lock or tag service panel to prevent power
from being switched on accidentally.
HOUSE
WIRING
(120 VAC)
CARDBOARD
(Use to protect
cooktop)
OJ Connect House Wiring (120 VAG) to hood. Use a piece of
Cardboard
to protect the cooktop, if necessary.
GREEN
GROUND
SCREW
Connect house black
to hood black wire, house white to hood
white
wire, and house ground under Green Ground Screw.
Securely tighten cable clamp onto house wiring.
PageS
INSTALL HOOD
KEYHOLE (4)
MOUNTING SCREW (4)
OJ Hang hood from (4) Mounting Screws. Slide hood towards
wall until mounting screws
are engaged in narrow end of
(4) Keyholes. Tighten mounting screws securely. A long
screwdriver works
best.
[II Replace bottom cover.
DUCT
TAPE
Connect ductwork to hood. Use Duct Tape to make joints
secure and air tight.
PAR20,
SOW MAX.
HALOGEN
BULB
(2)
- or-
R16,
40WMAX.
INCANDESCENT
BULB (2)
I3l Install (2) PAR20, 50 W Maximum Halogen Bulbs or (2)
Ri6, 40 W Maximum Incandescent Bulbs. Purchase bulbs
separately.
A. CAUTION: Bulbsmaybehot! Refer to bulbpackaging
.. for further information.
[II Replace filters, turn on power at service panel, and test for
proper operation.

ALLURE® QS2 SERIES
RANGEHOOD
NON-DUCTED FILTERS
If hood is to be installed Non-Ducted:
Purchase a set of
(2) Non-Ducted Filters from your local
distributor or retailer and attach them
to the aluminum mesh
filters.
NOTE: For models that are installed in the non-ducted mode,
the
most effective operation is achieved at speeds 1 and
2. These speeds provide the most efficient and quiet
operation during cooking, while maximizing the benefits
ofthe recirculating filtration system.
Page 6
OPERATION
Fan and Lights: 3 push button switches for each. Push any but-
ton to select one of 3 fan speeds orone of 3 light levels. Push the
same button to turn fan or light
off. Press another button to change
fan speed or light level. A light above each
fan button indicates the
fan speed.
Heat Sentry:
Your range hood is equipped with the Heat Sentry
feature, which monitorstemperature. The Heat Sentrywill automati-
cally turn the fan
on at its highest speed when the temperature is
above normal.
1) If a
fan setting is selected when the Heat Sentry is on, the light
above the
fan button will flash on and off.
2) Ifthe fan is offwhen the HeatSentry ison, the light above
fan button flash on and off rapidly.
After the temperature has lowered to normal, the fan will change to
the setting priorto the Heat Sentry turning
on.
Fuse: The hood control contains a fuse to protect it from power
surges. Ifthefuse has opened (blown), the green
fan-level indicators
will operate properly
when the fan buttons/switches are pressed -but
the
fan and lights will not turn on.
The fuse
isa5x20mm, 10Amp, Fast-Acting, 125V (min.).Common
manufacturerand part numbersare: Littlefuse,
217010; Bussmann,
GMA10A; Wickmann, 1942100. Radio Shack, Digikey (1-800-344-
4539), and most electronic supply stores have them in stock.
To replace the fuse:
1. Disconnect power at service entrance.
2. Remove filters, bottom panel, lightwire harness, and airchute.
3. Remove and inspect fuse. If it is DQ1 open (blown), additional
diagnostics
need to be done.
4. Install new fuse.
5. Re-assemble air chute, light wire harness, bottom panel, and
filters.
6. Turn on power and check hood/control operation.
CLEANING
A WARNING: To reduce the risk of electricshock, discon-
... neet from power supply before cleaning.
Aluminum mesh filters: Clean frequently using hot water
and a
mild detergent. Filters are dishwasher safe.
Charcoal filters: Clean filter surfaces frequently with a damp cloth
and a mild detergent. DO NOT immerse filters in water or put in
dishwasher. The special "Clean Sense" feature indicates when the
filter
is to be replaced.The blue and yellow stripswill blend to green
when
it is time to changethefilter.The "Clean Sense"feature works
best when facing toward the cooking surface.
To clean hood: Remove filters. Use adamp cloth and a mild deter-
gent to wipe all grease-laden surfaces.
Do not use abrasive cloth,
steel wool pads, or scouring powder
on the Teflon@-coated bottom
cover or on any painted surface.
Use care when cleaning blower
wheel -it must not become bent or misaligned.
DO NOT ALLOW
WATER TO ENTER MOTOR. Makesure all surfaces are completely
dry before re-installing filters
and restoring power.
Motor
is permanently lubricated. Do not oil or disassemble motor.
Teflon" is a registered trademark of DuPont.

ALLURE® QS2 SERIES
RANGEH
000
SERVICE PARTS
PART NO.
KEY NO.
DESCRIPTION
DamperlDuct Connector (includes hardware)
Screw, #8-18 x 14 Hex' (2 in package)
Motor capacitor (includes wire nuts & hardware)
Isolation Transformer
Namepla1e, White
Namepla1e, Almond
Nameplate, Black
Nameplate, Biscuit
Control Panel, White
(includes Key No.6 & hardware)
Control Panel, Almond
(includes Key No.6 & hardware)
Control Panel, Black
(includes Key No.6 & hardware)
Control Panel, Biscuit
(includes Key No.6 & hardware)
Screw for Plastic, #6 x Y2 Flat Hd. (3 in package)
Screw, #8-18 x 3/8 (2 in package)
Ground Screw
Scroll Cover, Outlet (includes hardware)
Scroll Cover, Front (includes hardware)
Control Assembly
(includes Key Nos. 6, 7& hardware)
Air Chute Assembly
(includes Key No. 15 & hardware)
Baffle
Screw, Metric M4 x 6mm (4 in package)
Motor Plate (Includes Key No. 18)
Motor Plate Mountin~ Kit (3 of each part)
Motor (includes Key o. 16)
Blower Wheel (Includes Key No. 21)
Retaining Ring
Lamp Socket Assembly
Light Panel, 30 in. White
Light Panel, 36 in. White
Light Panel, 42 in. White
Light Panel, 30 in. Almond
Light Panel, 36 in. Almond
Light Panel, 42 in. Almond
Light Panel, 30 in. Black
Light
Panel, 36 in. Black
Light Panel, 42 in. Black
Light Panel, 30 in. Biscuit
Light Panel, 36 in. Biscuit
Light Panel, 42 in. Biscuit
Light Panel, 30 in. Stainless
Light Panel, 36 in. Stainless
Light Panel, 42 in. Stainless
Hole Plug (1 req.)
Pop Rivet, .1250 (3 req.)
FiI1er Spring Kit
Bottom Cover, 30 in.
(includes Key Nos. 9, 25, & 26)
Bottom Cover, 36 in.
(includes Key Nos. 9, 25, & 26)
Bottom Cover, 42 in.
(includes Key Nos. 9, 25, & 26)
Autotransformer (includes hardware)
Aluminum Mesh Filter, 30 in. (2 in packagel
Aluminum Mesh Filter, 36 in. (2 in package
Aluminum Mesh Filter, 42 in. (2 in paCkage)
Non-Ducted Blower Wheet Assembly
(includes Key Nos. 20 & 21)
Non-duc1ed Filter Kit, 30 in.
Non-ducted'Filter Kit, 36 in.
Non-ducted Filter Kit, 42 in.
Wire Harness
Control Fuse, 1O-Amp
Page 7
17
--01
I
10
9
I -20 1--30
I
I -21 I
1 ___________ --'
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
..
**
..
..
*'
R740013
R602017
R334755
R501031
R627501
R627502
R627503
R627528
R169005
R169006
R169007
R169008
R601535
R602534
R602533
R660505
R680507
R111663
R401647
R401646
R601536
R651973
R169009
R520132
R531 068
R607215
R111630
R7201731
R7201751
R7201771
R7201732
R7201752
R7201772
R7201734
R7201754
R7201774
R7201735
R7201755
R7201775
R720174
R720176
R720178
R607660
*
R169016
R680515
R501034
99010302
99010303
99010304
R730111
99010308
99010309
99010310
R111627
R564074
Order replacement parts by PART NO. - not by KEY NO.
* Standard hardware - may be purchased locally. •• Not illustrated - purchase separately.

ALLURE® QS2 SERIES
RANGEH
000
Page 8
WARRANTY
BROAN-NUTONE ONE YEAR LIMrrED WARRANTY
Broan-NuTone warrants to the original consumer purchaser of its products that such products will be free from defects in materials or
workmanship for a period of one year from the date of original purchase. THERE ARE NO OTHER WARRANTIES, EXPRESS OR IMPLIED,
INCLUDING, BUT NOT LIMITED TO, IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FORA PARTICULAR PURPOSE.
During this one-year period, Broan-NuTone will, at its option, repair or replace, without charge, any product or part which is found to be
defective under normal use and service.
THIS
WARRANTY DOES NOT EXTEND TO FLUORESCENT LAMP STARTERS AND TUBES.This warranty does not cover (a) normal
maintenance
and service or (b) any products or parts which have been subject to misuse, negligence, accident, improper maintenance
or repair (other
than by Broan-NuTone), faulty installation or installation contrary to recommended installation instructions.
The duration of
an implied warranty is limited to the one-year period as specified for the express warranty. Some states do not allow
limitation
on how long an implied warranty lasts, so the above limitation may not apply to you.
BROAN-NUTONE'S OBLIGATION TO REPAIR OR REPLACE, AT BROAN-NUTONE'S OPTION, SHALL BE THE PURCHASER'S SOLE
AND EXCLUSIVE REMEDY UNDER THIS WARRANTY. BROAN-NUTONE SHALL NOT BE LIABLE FOR INCIDENTAL, CONSEQUEN-
TIAL
OR SPECIAL DAMAGES ARISING OUT OF OR IN CONNECTION WITH PRODUCT USE OR PERFORMANCE. Some states do
not allow the exclusion or limitation of incidental or consequential damages, so the above limitation may not apply to you.
Thiswarranty gives you specific legal rights, and you may also have other rights, which vary from state to state. Thiswarranty supersedes
all prior warranties.
To qualifyfor warranty service, you must (a) notify Broan-NuTone at the address or telephone number below, (b) give the model number
and part identification and (c) describe the nature of any defect in the product or part. At the time of requesting warranty service, you
must present evidence of the original purchase date.
Broan-NuTone LLC Hartford, Wisconsin www.broan.com 800-558-1711
Broan-NuTone Canada Mississauga, Ontario www.broan.ca 877-896-1119
628003B