BROKIS BONBORI CM12101 User manual

CM12101

BONBORI
Table light, Floor light
1x lamp body
1x upper section
1x cap
1x light source
1x glass shade
1x glass diffuser
1x pair cotton gloves
1x installation manual
3x M4x16 set screws
3x M6x25 hex screws
1x M4x4 set screw
1x power cable with connector
1x hex key size 1,5
1x hex key size 2
The manufacturer assumes no liability for
damage resulting from incorrect assembly.
When unpacking the light,
do so with regard for its material composition
– the main components are made of glass.
Wear the cotton gloves included with the light
when unpacking and assembling it.
INSTALLATION
MANUAL
COMPONENTS INCLUDED
WITH UNIT:
WARNING:
Installation time: 30 minutes / 1 person
BROKIS S.R.O.
ŠPANIELOVA 1315/25
163 00 PRAHA 6 - ŘEPY
CZECH REPUBLIC
ORG. ID 64940799
VAT ID CZ64940799
C 42174 MĚSTSKÝ SOUD
V PRAZE
TEL [phone]
[e-mail]
[e-mail]
WWW.BROKIS.CZ PAGE 2
Download

CLEANING THE GLASS
BROKIS applies the highest possible quality standards in manufacturing its lights. Prior to shipping, each light
undergoes several quality controls and stages of cleaning. Lights may require additional cleaning as a result of
transportation, storage, and the amount of time that passes between packing in our plant and subsequent
unpacking by the client. Therefore, we emphasizes cleaning the lights prior to installation.
The glass must first be rinsed in hot water, with a dilution of a dish-detergent used to remove all foreign
particles and dust. Eventually repeat this basic treatment, if necessary. Afterwards the glass must have a second
cleaning using hot water, with a dilution of a de-greaser (such as ammonia or vinegar). The glass must then be
thoroughly rinsed with running hot water. Eventually repeat this treatment, if necessary. The glass is then
thoroughly dried with a paper towel or a clean soft cotton towel. Only re-assemble the glass to the lamp body,
when completely cooled down.
Do not use mineral spirits, highly concentrated thinners, or other substances not intended for use on glass
surfaces. Also: do not use products, containing silicones – since they will rapidly attract more dust and grease.
PRIOR TO SHIPPING, THE FUNCTIONALITY OF EACH LIGHT AND ITS COMPONENTS IS THOROUGHLY TESTED.
THE MANUFACTURER ASSUMES NO LIABILITY FOR THE MISHANDLING OF PRODUCTS.
BONBORI
Table light, Floor light
INSTALLATION
MANUAL
BROKIS S.R.O.
ŠPANIELOVA 1315/25
163 00 PRAHA 6 - ŘEPY
CZECH REPUBLIC
ORG. ID 64940799
VAT ID CZ64940799
C 42174 MĚSTSKÝ SOUD
V PRAZE
TEL [phone]
[e-mail]
[e-mail]
WWW.BROKIS.CZ PAGE 3
Cleaning information

Screw the light source into the fixture.
Insert the diffusor into the top of the body. When doing so, hold the body at an angle to prevent damage to the diffusor, then
return it to a vertical position.Insert the diffuser into the light through the open side!
Turn the 3 set screws (M4x16) from the inside of the body so that they are flush with the outer surface of the light.
Position the upper section on the set screws (M4x16) and turn it to secure the bayonet.
Tighten the set screw (M4x4) at the top of the body to prevent the upper section from turning.
Position the glass shade on the body with the larger opening facing downwards and install 3 set screws (M6x25) into the
holes in the upper section.
ASSEMBLING THE LIGHT
1.
PAGE 4

Loosen the set screw (M3x3) on the power cable connector. Insert the cable connector into the connector on the light and
turn the sleeve to close. Retighten the set screw in the connector.
CONNECTING THE LIGHT
2.
PAGE 5

Plug the power cable into an electrical outlet and verify that the light works properly.
SWITCHING ON THE LIGHT
3.
PAGE 6