Brunner Eos 8 User manual

User guide

EOS 8

CONTENTS

1 Registration.................................................................... 4

2 System description........................................................4

2.1 Functional principle myBRUNNER local..................................6

3 Licenses..........................................................................8

4 Operation........................................................................ 9

4.1 Menu...................................................................................... 10

4.1.1 Network adverts.......................................................10

4.2 Combustion log......................................................................11

4.3 Display customization............................................................ 12

4.4 Eco-function........................................................................... 17

4.5 Lighting fire in a cold fireplace.............................................. 18

4.6 Adding fuel in a warm fireplace.............................................19

4.7 Winter/Summer-operation...................................................... 20

4.8 Priority switching....................................................................20

4.9 Type of wood......................................................................... 21

4.10 Remote access via myBRUNNER.........................................22

4.10.1 Registration..............................................................22

4.10.2 Logging in................................................................35

4.10.3 Enabling for Service access....................................37

4.10.4 Synchronisation with network..................................39

5 Brunner App.................................................................40

6 Emergency Operation................................................. 42

6.1 Heating with manually controlled combustion air supply....... 42

7 Cleaning........................................................................ 44

8 Changing the battery...................................................44

9 Caution messages....................................................... 45

10 Error massages............................................................48

11 Update of the control unit.......................................... 51

11.1 Software from PC on the USB-Stick..................................... 52

11.2 Software from USB-Stick on the control unit......................... 54

11.2.1 Variant 1.................................................................. 54

11.2.2 Variant 2.................................................................. 57

11.3 What to do if the update does not start ?.............................. 58

12 Remove of the Touch-Display.................................... 59

Please read the entire User Guide before lighting the fire for the first time. In par-

ticular, please note the safety precautions in this manual.

Installation must be carried out by an authorized stove-fitter, because safety and

efficiency of the system depend mostly on proper installation of the product. All

valid stove fitting rules and regulations of building law must be observed and fol-

lowed.

This fireplace is subject to the provisions of 1. BlmSchV.

Necessary national and European standards and local regulations must be ob-

served.

Old devices contain recyclable materials. Please follow the applicable national

regulations for disposal.

Please follow the relevant regulations of your country. In case of doubt, check the

valid conditions for the operation of fireplaces in your local area.

Subject to technical changes!

Please keep the User Guide for future reference!

Waste on fire = Toxins in your garden

Generalities

The control unit EAS is a LINUX-based microprocessor with a 5,7 inch high reso-

lution graphic touch display.

With this technology all self-describing functions are operated, adjusted and dis-

played. This applies to all other BRUNNER components which are connected

over the CAN bus.

The USB interface on the back of the display serves for loading of updates. This

way the newest software can always be loaded and used.

1 REGISTRATION

Under http://produktregistrierung.brunner.de you can reg-

ister your EOS 8 under indication of the batch number (on

the packing or on the back of the product release note).

2 SYSTEM DESCRIPTION

The EOS 8 provides functions which make it possible to perform complex control

tasks related to heating systems. The integrated functions of EOS 8 are optimized

for the control of heating systems with boiler technology and a connected buffer

tank. In connection with a BHZ, for example, it is possible to operate the complete

system comfortably from one place.

It is possible to connect extra displays to the EOS 8. In this case, the heating sys-

tem can be operated from each connected display. If further systems, like BHZ

for example, are using the data bus technology, then the entire system can be op-

erated from each connected display. The currently active component (e.g. EOS

8) is shown in the foreground. Other systems (e.g. BHZ) can be selected via their

symbols in the navigation bar below and displayed for operation.

All sensors, actuators, pumps, etc. are connected to the electronics of the EOS 8.

The EOS 8 display unit is connected to the control unit with a connecting cable.

Display

The display of EOS 8 is divided into three fields.

In the navigation bar above, the essential functions/components of the current ap-

plication are represented by icons. By tapping an icon you can enter the respec-

tive menu.

In the lower navigation bar on the right, the current date and time are displayed.

In the same navigation bar, the different applications (EOS 8, BHZ, etc.) can be

selected if available.

In the field between the two navigation bars, the different menus, diagrams, infor-

mations etc. concerning the selected application/function are displayed. Contents

depend on the configured system.

Illustration 1: EOS 8 Home view

The touchscreen of the control unit can be operated with fingers. If this is not de-

sired or if it does not feel practicable, a suitable aid can be used. Never operate

the touchscreen with a conventional pen. A stylus for capacitive displays is re-

quired.

Hint: The display does not respond to pressure. Sometimes coming close with a

finger already leads to a reaction. Touch the desired place of the screen and do

not keep your finger on it.

Never use a pencil or other sharp objects for operation.

2.1 FUNCTIONAL PRINCIPLE MYBRUNNER

LOCAL

You can also reach and query your system conveniently via myBRUNNER

local. For this you do not need internet access with the myBRUNNER local

function. Simply connect your system to the home network and access the

control panel directly and internally via your intranet.

It is important that your device is also connected to the same home net-

work!

NOTE: This feature works only through the myBRUNNER app.

1Internet connection

2 or

3 Wired with integrated network interface (Ethernet)

4 Distributor (switch)

5 Wireless with integrated WLAN interface

6 myBRUNNER app on terminal on the home network

7 Internet-enabled terminal with browser or myBRUNNER app

3 LICENSES

For the visualization of our user interface we use an open source operating sys-

tem, which is subject to different license models.

You can see the licenses used in the software under the menu:

„Settings“→“Display“→“Licenses/Contact“

Written Offer

(open source software)

Our product contains software and sourcecode whose rightholders license it under the terms

of the GNU General Public License, version 2 (GPLv2), version 3 (GPLv3), the GNU Lesser

General Public License, version 2.1 (LGPLv2.1), version 3 (LGPLv3) and other open source

software licenses.

If you send us a request for oversending the licensed source code of the software, please use

the following address:

Ulrich Brunner GmbH

Zellhuber Ring 17-18

84307 Eggenfelden

[email protected]

Upon request, we will send you a CD-ROM with the provided source codes. You have to pay

the costs for material, packaging and delivery.

The offer is valid for at least three years from the date of delivery of the product on which the

software is installed, and as long as we can offer spare parts and customer service for this

product, or from the time of downloading the software from our homepage.

Please include the type of product for which you want to receive the source code in your re-

quest.

4 OPERATION

The operation of the EOS 8 is done completely over the attached display/dis-

plays. From here all devices connected over the data BUS can be attained. The

available devices are shown in the lower navigation bar.

The EOS 8 thus represents a complex system, in which all connected devices are

considered. Since individual functions can in principal be taken over by different

devices (e.g. steering of the pumps), the function concerned is always taken over

by the equipment that is most suitable for this. To the other devices, the function

is then faded out and not available.

In this manual all combinations of devices and functions cannot be treated due to

the complexity mentioned. Therefore only the fundamental procedure for opera-

tion is described here.

In the lower navigation border the connected devices are displayed and in the up-

per navigation border the therefore activated functions are shown. By touching

briefly the symbols one attains the respective info menus and/or the available pa-

rameter settings.

Under 'Settings' one finds the possibilities to configure the EOS 8 and to adapt it

to your installation. Select the menu option and enter the pin code 9999.

Before changing parameters under 'Settings', one should attach a

USB stick (on the back of the display) and under Settings /Anlage/

Sicherung erstellen.

4.1 MENU

In the menu some basic functions of the EOS can be programmed.

The possibilities depend on the configured installation.

4.1.1 NETWORK ADVERTS

Display with a myBRUNNER connection

Display for an existing network connection, whether

WLAN or LAN.

Display with a myBRUNNER-local connection

globe No network

4.2 COMBUSTION LOG

Softkey Menu - 2nd Page

Indication

Heat-up Combustion counter

How often the Heat. Err. Temperature was ex-

ceeded and combustion step was changed prop-

erly to Phase 2

Reload Reloading counter How often wood was reloaded within Phases

from 2 to 4

Heat up er-

ror Heat up error counter How often a heat up error was detected when

lighting a fire.

Heating er-

ror Heating error counter How often a heating error was detected during

combustion.

Indication

Combustion

hours

Working hours

counter

How many hours passed, as the

control system was in Phase 2, up to 4.

Stove hot Stove hot counter How often the threshold value was exceeded.

4.3 DISPLAY CUSTOMIZATION

The display of the EOS 8 is customizable with different display options.

This chapter describes all possible settings for display options.

Tap the softkey Settings and enter your PIN code.

Follow the path: Settings (Code 9999) / Display / Settings and the follow-

ing window appears:

A window appears, where you can set the time for screen saver display:

Screen saver is shown automatically after .... min-

utes

1. Please follow the path on display:

Settings / Control panel / Settings / Standby after

2. When you click on the white field at Standby af-

ter .... a new window will appear;

3. Set the desired time (in minutes):

a) by tapping + or -

b) by moving your finger on the sliding bar; the num-

ber of minutes is shown below the sliding bar

4. Confirm by pressing O.K.;

→ The settings are applied.

Illustration 2: Display cus-

tomization - Screen saver

With this setting, the screen saver will appear after a desired time.

To set the Brightness of display

The brightness of Touch Display can be adjusted to local conditions.

To set the screen brightness, proceed as follows:

1. Follow the path: Settings / Control panel / Settings /

Brightness

2. When you click on the white field at Brightness a

new window will appear:

3. Set the desired brightness of the screen:

a) by tapping + or -

b) by moving your finger on the sliding bar to the right

or left

4. Confirm by pressing O.K.

→ The settings are applied.

Illustration 3: Display cus-

tomization - Brightness

You can set the length of the long sound, which indicates errors or status messages.

To set the length of the long sound,

1. Follow the path:

Settings / Control panel / Settings / Long signal

2. When you click on the white field at Long signal a

new window will appear:

3. Set the desired time (in seconds):

a) by tapping+ or -

b) by moving your finger on the sliding bar to the right

or left;

4. Confirm by pressing O.K.

→ The settings are applied.

Illustration 4: Display customiza-

tion - Long signal

You can set the length of the short sound, which indicates the status messages.

To set the length of the short sound,

1. Follow the path:

Settings / Control panel / Settings / Short signal

2. When you click on the white field at Short signal a new window will appear:

3. Set the desired time (in seconds):

a) by tapping + or -

b) by moving your finger on the sliding bar to the right or left

4. Confirm by pressing O.K.

→ The settings are applied.

You can set the interval for repetition of sound signals, which indicate errors (error mes-

sages) or status messages.

To set the length the interval for repetition,

1. Follow the path:

Settings / Control panel / Settings / t Sign. repeat.

2. When you click on the white field att Sign. repeat. a new window will open:

3. Set the desired time in seconds:

a) by tapping + or -

b) by moving your finger on the sliding bar to the right or left

4. Confirm by pressing O.K.

→ The settings are applied.

Function Logout after

You can set the waiting time for automatic closing of the Settings area, when no entry is

made (Settings log-out).

To set the waiting time, proceed as follows:

1. Please follow the path:

Settings / Settings / Control panel / Logout after

2. A dialog with sliding bar appears;

a) by tapping + or -

b) by moving your finger on the sliding bar to the right or left

3. Confirm by pressing O.K.

→ The settings are applied.

Automatic daylight saving time

To enable automatic switching between Summer and Winter time, you must set the time

zone of your residence.

To enable Timezone setting:

1. Please follow the path:

Settings / Settings / Control panel / Timezone

2. A window for timezone selection will appear:

3. Select your timezone;

4. Tap O.K. to confirm;

→ The settings are applied. Illustration 5: Display Indi-

vidualisierung Zeitzonen

Screen saver

You can change the appearance of your screen saver. You can choose between analog

clock, digital clock and black display.

To change the screen saver, proceed as follows:

1. Please follow the path:

Settings / Control panel / Settings / Screen saver

2. A dialog with the above options appears. Touch the desired screen saver to select.

3. Tap O.K. to confirm;

→ The settings are applied.

Language

You can change the desired language of boiler controls even after configuration of the boil-

er. Not available languages are dimmed on the screen.

To change the language setting, proceed as follows:

1. Please follow the path:

Settings / Control panel / Settings / Language

2. A dialog with flags will appear;

3. Select the flag corresponding to your language;

The language setting is applied.

4. If the language setting is changed, the control unit will restart;

5. The control unit will restart after tapping O.K. to confirm

→ The control unit is initialized again, and the language is changed.

Design

The visual appearance of Touch Display can be adjusted to local conditions. You can select

between the background colors: White / Black.

This process takes approx. 1 minute.

To change the visual appearance, proceed as fol-

lows:

1. Please follow the path:

Settings / Control panel / Settings / Design

2. A selection window will show up, where you

can select the desired setting (white or black)

with your finger.

3. Tap O.K. to confirm Illustration 6: Display Design selec-

tion

4. Please wait, until the control unit reboots automatically (approx. 1 minute)

→ The settings are applied.

Illustration 7: Black display design Illustration 8: White display design

4.4 ECO-FUNCTION

Touching the tiled stove symbol in the upper navigation

bar leads to the tiled stove information page. Above on

the left in the middle navigation field now the symbol for

the Eco-function appears.

Clicking on it leads to the

adjusting page:

Here one can choose be-

tween Yes and No. Con-

firm by O.K.

With activated Eco-func-

tion, the messages for

heating errors are dis-

played.

Illustration 9: Setting Eco-function

4.5 LIGHTING FIRE IN A COLD FIREPLACE

1 Open the firing door. A short functional inspection of the EOS7 takes

and the combustion air valve is driven into the starting up position. The

sensor at the exhaust gas stub announces the combustion temperature.

Make sure that the level of ashes is not too high. Maximum level: 5 cm

below the door frame.

2 Load some chopped firewood loosely into the fireplace. Load the de-

sired amount of wood logs on this small wood. Put a good fire-starter,

such as Fidibus between the logs and light the fire. Fire-starters are

practical fire starting aids. Please note: big logs are not easy to light and

heavy to burn in a cold fireplace. Never use petrol or alcohol as aids for

lighting fire!

3 Close the firing door. From now on the EOS takes over the control of

the combustion air valve. Closing the door is the signal for the EOS

that a heating procedure is started. The message “1. Heating up” ap-

pears and the heating up temperature is displayed. In this position the

air valve is fully opened, so that a fast high heating is possible. The fast

high heating is the most important factor in order to obtain a clean com-

bustion with reduced emissions.

If the heating up temperature is reached in the given time, the marking

becomes green, otherwise it becomes red and the message ‘Heating up

error’ is displayed.

The second marking for a clean combustion is displayed. When this

temperature threshold is exceeded, the combustion air valve motor dri-

ves the combustion air valve further step by step. If this temperature

threshold is not reached, the message ‘Heating up error’ appears and

the second marking is displayed in red.

If after closing of the firing door the message “1. Heating up” is

not displayed, then there is a defect. Please control the heater

manually and inform the stove builder.

4.6 ADDING FUEL IN A WARM FIREPLACE

1 According to the heat requirement, a new combustion can be started.

However, please not the basic rule that only after complete burning of

the previous load, a further load can be added. The wood burning con-

cept requires that load after load is burned, and not log after log.

2 2. When the message „Glut“ appears, some glow from the last burn-up

is remaining in the combustion chamber. The newly added fuel takes

fire on this glowing ember bed. Put some wood shavings directly on the

glow (maybe ‘loosen up’ a little the ember bed) for easier igniting. Close

the firing door again.

From now on the EOS takes over the control of the combustion air

valve. Closing the door is the signal for the EOS that a heating proce-

dure is started. On the display the markings and messages appear as

described in the chapter 'Lighting fire in a cold fireplace' .

Each opening and closing of the firing door is a signal for the EOS

to start monitoring functions. The electronics now expect the start

of a heating procedure. If no or too little fuel is loaded, an error

message appears. Avoid therefore an unnecessary opening of the

firing door!

4.7 WINTER/SUMMER-OPERATION

Switching between winter and summer mode will be done in the menu:

Menu / Damper flap operation/ Winter operation/ Summer operation.

Confirm selection with O.K.

Winter mode = operation of the damper flap

Summer mode = the damper flap always remains open

4.8 PRIORITY SWITCHING

Priority of room heating or water heating

Set the priority of heating: Room heating or water heating

Menu / Priority/Stove = Room heating

Water = Water heating

For installations with an automatic switching between boiler function and stove

function, the priority function can be selected. Water priority leads to it that the re-

quired values, e.g. the required buffer tank temperature, are maintained by the

EOS if possible. Stove priority makes that the switching flap does not switch to

the boiler function; the burn-up is always done over the stove (smoke channels).

This manual suits for next models

Table of contents

Other Brunner Control Unit manuals

Brunner

Brunner EAS 3 User manual

Brunner

Brunner EAS 3 Installation manual

Popular Control Unit manuals by other brands

Satel

Satel GSM LT-1 user manual

M-system

M-system R3-SV8C instruction manual

Siemens

Siemens SINUMERIK 840Di sl operating manual

Texas Instruments

Texas Instruments TPS53515 user guide

Val Controls

Val Controls I 24-AF Series Replacement guide

Intel

Intel Stratix 10 user guide

Aaeon

Aaeon ETX-945GSE manual

Kohler

Kohler K-402 installation guide

TP-Link

TP-Link kasa smart KE100 V1.20 quick start guide

nologo

nologo START-S5PV Manual for the installer

T&S

T&S B-7000 Series Installation and maintenance instructions

GIGAIPC

GIGAIPC CE6-6412A manual

Nordson EFD

Nordson EFD 781Mini Series operating manual

Cooper Tools

Cooper Tools Cleco TME-111 Programming manual

GRAUPNER

GRAUPNER 23108 Installation and Usage

Movelar

Movelar tuozi KITAWAY MODULE 84 F manual

Siemens

Siemens Simatic S7-1500 manual

Parker

Parker C10 Cable Assembly

Brunner EOS 8 User manual

Popular Control Unit manuals by other brands