BRYANT DENTAL IGNIS User manual

A BRYANT DENTAL PRODUCT

[phone] |[phone]

Bryant Dental is empowering dentists with technology
that is beautifully designed and expertly engineered.
Innovation in prototyping with rapid 3D modelling
and precision printing, combined with the latest AI
technology in customer service, allows us to deliver
to you products previously thought impossible.
Smart dentistry
in a whole new light.
Wireless Light System
Contents
06 Ignis®Instructions
10 Charging
11 Technical
12 Safety Instructions
14 Servicing and
Troubleshooting
15 Disposal Notice
15 Warranty
www.bryant.dental |03

HINGELESS
Rotating lens
filter design.
UNIFORM BEAM PATTERN
Edge-edge conformity
for maximum clarity.
[phone] |[phone]

Neodymium magnets hold
the battery securely in place and
allow a super quick swap-over
time of less than three seconds.
NO FIDDLING WITH
SCREWS OR WIRES
Cool Blue Indicator light
for battery management.
INDICATION
Head strap is a specialised silicone rubber,
which is disinfectable and non-sticky.
SPECIALISED SILICONE RUBBER
PLEASE DO NOT USE if you
have a silicone rubber allergy.
www.bryant.dental |05

Ignis® Instructions
The Ignis®Kit does not come pre-asssembled. Please follow
the instructions presented for usage. A screw driver is
provided if you require further adjustments. If you experience
any problems please contact us on [phone].Note: Loupes not included
Intended use: Ignis®Wireless Headlight is an illumination
device attached to spectacles that is intended to
illuminate oral structures and operating areas.
This device is designed to be used by qualified dental
professionals, including, but not limited to, dentists
and dental hygienists, as well as medical doctors and/
or professionals. Ignis®must be used with the bracket
provided, which is specific to your frames.
What’s included
 Ignis® LED with
integrated headstrap
X1 Dichroic Wavelength Filter
X2 Ignis® Batteries
X1 Battery Charging Plate
X1 Ignis® USB Wall Plug
(country specific)
X1 Ignis®Screw Driver
X1 Ignis®Bracket
Attaching Ignis®LED
Attach Ignis®LED to the Loupes using the
Ignis® Bracket the Ignis®Screwdriver and.
Ensure placement is in the middle of the
bridge arm (shown below).
[phone] |[phone]

www.bryant.dental |07
Attach the battery switch to the base plate attached on the head
strap, aligning the grooves to the ‘OFF’ position (shown below).
Attaching the battery switchAttaching O-Rings
Neodymium magnet-powered
battery switch
Base plate
Slide the O-Rings down the right Loupe arm
(see O-Ring positioning shown above) to hold
power cable. Then slide the head strap over
the memory metal earpieces (shown below).
Head strap

Regular
Twist one
click for
regular power
(shown above).
Off
Keep switch
vertical to
power off device
(shown above).
High
Twist two clicks
for high power
(shown above).
Battery takes 1.5s
to power up when
switched ON to calculate
optimum output.
Select power modes
[phone] |[phone]
IMPORTANT: For safety reasons, to operate in high power mode, the battery must first be switched to regular and then to high.
Blue indicator
lights are
activated when
device is ON.
When indicator
light does not show
any bars, the battery
is near depletion
and requires
charging. (See page
10 for charging.)

www.bryant.dental |09
Dichroic Lens Filter – this smart filter
is held in place with six neodymium
magnets, allowing a really smooth
transition between regular light
and filtered light. This design
prevents the filter accidentally
rotating into place.
Selecting the lens lter
This filter cuts out the curing wavelengths
of light, to prevent composite setting with
a bright yellow tint rather than dark orange.
This allows fine aesthetic work with the light on.
TO AVOID DAMAGE.
Please do not lift the
lens filter upwards.
Rotate only.
Dos and Don’ts
ROTATE LIFT
5

Charging
It’s important to take care of the batteries.
Intelligent adaptive charging means the
batteries cannot be overcharged. Each battery
comes with a two-year warranty.
CHARGED IN 1 HOUR 45 MINS
[phone] |[phone]
Detach the battery from
the head strap plate.
Combine your USB mains
adaptor and battery charging plate
together (shown below).
Attach battery to battery charging
plate. Aligning the grooves on
the top to activate the charging
sequence (shown above).
Once a FULL bar
appears and stops
flashing, the battery
is fully charged.
Battery position
Do not expose batteries
to naked flame.
Neodymium magnet-powered battery switch.
USB mains adaptor attached to battery
charging plate.