Bside ADM02 User manual

Table of Contents
1. Introduction ………………………………………………. 1
2. Safety note ……………………………………………..… 2
3. Explanation of Controls and
Indicators …………………... 3
3-1. Product illustration ……………………………………….
3
3-2. Functional push button …………………………………….
4
3-3. LCD display ………………………………………………. 5
4. Specification ………………………………………………. 6
4-1. General Specification ……………………………………...
6
4-2. Electrical Specification ………………………………….
7- 9
5. Measurement operation …………………………………..
9
5-1 DC voltage & AC voltage
measurement ………………... 9
5-2. Resistance
measurement …………………………….….. 10
5-3. Diode & Continuity
check ………………………..…..… 10

5-4. DC/AC ¸ A or mA measurement ………………….…….
11
5-5. DC/AC 10A measurement …………………………..….
12
5-6 Temperature
measurement ………..…. 12
6. Maintenance ……………………………………………….
12
6-1. Replacing the battery …………………………...……….
12
6-2. Replacing the fuse ……………………………………….
12
6-3. Cleaning and
Decontamination …………………………. 13
1. Introduction
This Meter is a handheld and battery operated Digital Multi
Meter(DMM) with multi function. This Meter is designed to
meet IEC61010-1 & CAT II 600V over voltage category and
double insulation. The meter with holster that is giving the
main body, though downsized, high resistance against the
shock of a drop.
This operating instruction covers information on safety and
caution. Please read relevant information carefully and
observe all the warnings and note strictly.
The DMM as general measurement tool and widely used in
the school, laboratory, factory and other social field.

2. Safety note
Warning
To avoid possible electric shock or personal injury and to
avoid possible damage to the meter or to the equipment
under test, adhere to the following rule:
Do not apply more than the rated voltage, of marked on
the meter, between the input terminal and grounding
terminal..
Do not apply voltage between COM and OHM terminal,
in the resistance measuring state.
Do not measure current with test lead inserted into
voltage or OHM terminal.
Do not expose the instrument to the direct sun light,
extreme temperature and humidity or dew full.
Inspect the test lead for damaged insulation or exposed
metal.
Before measuring current, check the Meter”s fuses and
turn off power to the circuit before connecting the meter
to the circuit.
Disconnect circuit power and discharge all high voltage
capacitors before testing continuity, diode, resistance,
capacitance or current.
Note international Electrical Symbol.
Dangerous
Voltage
Ground
AC
Alternating
current
Warning
see explain in manual
1

DC (Direct
Current)
Fuse
AC or DC
Measurement category(over voltage category):
This instrument is meet the safety condition of CAT II.
The equipment is used for measurement in building
facilities. Examples are measurements on distribution
boards, circuit breaker and industrial equipment
located in fixed facilities, as a fixed motor.
3. Explanation of controls and indicators
3-1. Meter illustration
2

Fig. 1 Exterior view
1. LCD display 2. ‡ MAX· push button 3. ‡ BACK LIGHT·
push button 4. “HOLD· push button 5. ‡ FUNC· Push
button 6. Rotary Switch (Knob) 7. ‡ V/Ω
/uA/mA/Temp· Input terminal
8. ‡ COM· input terminal 9. ‡ 10A· input terminal
3-2. Functional push button
Push
button
Function
Func
“FUNC” key is the function select key
that acts with trigger. Use the key as
switch of DC/AC current,
Diode/Continuity and ₤ /₦ .
HOLD
Press “HOLD· to enter and exit the hold
mode in any mode. That act with trigger.
MAX
This key is act with trigger. Press this key
once, the maximum value is holding (Will
displays “MAX’ symbol in the LCD).
After pressing the key, A/D will keep
working, and the display value are always
up dated and kept the maximum value.
NOTE: The actual gained value is not the
peak value.
3

This key is used control Backlight. This key
is act with trigger. When press and hold
the key over 2 sec, will enable Backlight.
Press the key again , the backlight will
disable.
3-3. Display indicators
Fig. 2 LCD
Indicator Meaning
DC voltage or current
AC voltage or current
Diode
MAX Maximum value
HOLD Data hold
Low battery indicator
MKέ έ Kέ Mέ is unit of resistance
₤ /₦
The unit of temperature
(₤ : Centigrade; ₦ : Fahrenheit)
4

¸ mVA
mV ,V is unit of voltage
¸ A, mA, A is unit of current
１ Indicate negative reading
4．Specification
4-1. General Specification
◤ Auto ranging DMM , that full scale is 2000 counts
◤ Display : 3 1/2 digit LCD display..
◤ Over load protection: Used the PTC protection circuit for
Resistance, temperature measurement.
◤ DATA HOLD function
◤ MAX value hold function
◤ Back Light
◤ Low battery indication
◤ Auto Power OFF. : If the meter is idle for 15 minutes (idle
time), the meter automatically turns the power off. After
auto power-off, pushing any of the push button or
changing the rotary switch can turn on the meter again.
NOTE: ，1－After auto power off in the AC mode, if changing
the rotary switch to the DC mode, the
Re-power on if disabled.
(2) The meter enters sleep mode after Auto power
off. If press ‡ HOLD· push button to re-power
on in the sleep mode, the auto power off
function is disabled.
◤ Operating temperature & Humidity:
0 ~ 40₤ (32 ~104 ₦ ) & < 80% RH
◤ Storage temperature & Humidity:
-10 ~ 50₤ (14 ~ 122 ₦ ) & <70%RH
◤ Power Supply: 9V Battery(6F22 or 1604A Type) x 1pc.
◤ Safety Class: IEC 61010-1, CAT II 600V.
● Dimension(L x W x H) & Weight:140 x 67 x 30mm, Approx.
5

112g
4.1.1 Accessory :
1. User”s Manual ---------------------------- 1pc
2. Test lead ---------------------------- 1set
3. 9V Battery --------------------------- 1pc
4. K-type temperature probe[P3400]---- 1pc
4-2. Electrical Specification ( at 23±5₤ ; <75% RH)
4.2.1 DC Voltage
Range Resolutio
n
Accuracy
200m
V
0.1mV
±，0.5% rdg + 2dgt－
2V 0.001V
20V 0.01V
200V 0.1V
600V 1V ±，0.8% rdg + 2dgt－
* Over load protection: SG(Spark Gap) used to protect that
the voltage overload 1500V
4.2.2 AC Voltage
Range
Resolutio
n
Accuracy
2V
(40Hz-400Hz)
0.001V
±，1.0% rdg + 3dgt－
20V
(40Hz-400Hz)
0.01V
6

200V
(40Hz-400Hz)
0.1V
600V
(40Hz-200Hz)
1V
±，1.2% －rdg + 3dgt
* SG(Spark Gap) used to protect High voltage that is
over 1500V.
4.2.3 Resistance
Range Resolution
Accuracy
200έ 0.1έ
±，0.8% rdg + 2dgt－
2kέ 0.001kέ
20kέ 0.01kέ
200k
έ
0.1kέ
2Mέ 0.001Mέ
±，1.0% rdg + 2dgt－
20Mέ 0.01Mέ
4.2.4 Diode check
Range
Resolution Function
0.001V
Will display the forward drop
voltage.
* Operating current＞about 1mA
* Open circuit voltage＞about 1.48V
4.2.5 Continuity
Rang
e
Function
87

If measured resistance less than 100 έ , will
buzzer is sounded.
* Open voltage: about 0.5V
4.2.6 DC Current
Range
Resoluti
on
Accuracy
200¸ A 0.1πA
±，1.5% rdg + 3dgt－
2000¸
A
1¸ A
20mA 0.01mA
200m
A
0.1mA
10A 0.01A
* Over Load protection＞use the fuse(F250mA/250V) at ¸ A
/mA range,
and use the fuse(F10A/250V) at 10A
range.
* Max input current:＞250mA at “mA” input terminal and
10A at “10A” input terminal.. .
4.2.7 AC Current [40Hz-400Hz]
Range
Resoluti
on
Accuracy
200¸ A 0.1¸ A
，1.5% rdg + 4dgt－
2000¸
A
1¸ A
20mA 0.01mA
200m
A
0.1mA
10A 0.01A
* Over Load protection＞use the fuse(F250mA/250V) at ¸ A