BSL Twist Beam 7LED User manual

USER MANUAL
Twist Beam 7LED
L ED -M o v i n g -H e a d

KEEP THIS MANUAL FOR FUTURE NEEDS

2
Every person involved with the installation, operation and maintenance of this device has to
- be qualified
- follow the instructions of this manual
- consider this manual to be part of the total product
- keep this manual for the entire service life of the product
pass this manual on to every further owner or user of the product
download the latest version of the user manual from the Internet
CAUTION!
Keep this device away from rain and moisture!
Unplug mains lead before opening the
housing!
For your own safety, please read this user manual carefully before you initially start-up.
INTRODUCTION
Thank you for having chosen our model. We are confident that our excellent products and service can satisfy
you. You will see you have acquired a powerful and versatile device.
Unpack the device you will find following items inside the box:
1. The fixture device
2. User manual
3. Omega holder with quick-lock fastener
4. DMX cable 3m
5. PowerCon power supply cable 1.5m
6. Safety rope
SAFETY INSTRUCTIONS
This device has left our factory in absolutely perfect condition. In order to maintain this condition and to ensure
a safe operation, it is absolutely necessary for the user to follow the safety instructions and warning notes written
in this user manual.
Important:
Damages caused by the disregard of this user manual are not subject to warranty. The dealer
will not accept liability for any resulting defects or problems.
CAUTION!
Be careful with your operations. With a dangerous voltage you can suffer a dangerous
electric shock when touching the wires

3
If the device has been exposed to drastic temperature fluctuation (e.g. after transportation), do not switch it on
immediately. The arising condensation water might damage your device. Leave the device switched off until
it has reached room temperature.
Please make sure that there are no obvious transport damages. Should you notice any damages on the A/C
connection cable or on the casing, do not take the device into operation and immediately consult your local
dealer.
This device falls under protection-class I. The power plug must only be plugged into a protection class I outlet.
The voltage and frequency must exactly be the same as stated on the device. Wrong voltages or power
outlets can lead to the destruction of the device and to mortal electrical shock.
Always plug in the power plug last. The power plug must always be inserted without force. Make sure that the
plug is tightly connected with the outlet.
Never let the power-cord come into contact with other cables! Handle the power-cord and all connections with
the mains with particular caution! Never touch them with wet hands, as this could lead to mortal electrical
shock.
Never modify, bend, strain mechanically, put pressure on, pull or heat up the power cord. Never operate next
to sources of heat or cold. Disregard can lead to power cord damages, fire or mortal electrical shock.
The cable insert or the female part in the device must never be strained. There must always be sufficient cable
to the device. Otherwise, the cable may be damaged which may lead to mortal damage.
Make sure that the power-cord is never crimped or damaged by sharp edges. Check the device and the
power-cord from time to time.
If extension cords are used, make sure that the core diameter is sufficient for the required power consumption
of the device. All warnings concerning the power cords are also valid for possible extension cords.
Always disconnect from the mains, when the device is not in use or before cleaning it. Only handle the
power-cord by the plug. Never pull out the plug by tugging the power-cord. Otherwise, the cable or plug can be
damaged leading to mortal electrical shock. If the power plug or the power switch is not accessible, the device
must be disconnected via the mains.
If the power plug or the device is dusty, the device must be taken out of operation, disconnected and then be
cleaned with a dry cloth. Dust can reduce the insulation which may lead to mortal electrical shock. More
severe dirt in and at the device should only be removed by a specialist.
There must never enter any liquid into power outlets, extension cords or any holes in the housing of the
device. If you suppose that also a minimal amount of liquid may have entered the device, it must immediately
be disconnected. This is also valid, if the device was exposed to high humidity. Also if the device is still
running, the device must be checked by a specialist if the liquid has reduced any insulation. Reduced
insulation can cause mortal electrical shock.
There must never be any objects entering into the device. This is especially valid for metal parts. If any metal
parts like staples or coarse metal chips enter into the device, the device must be taken out of operation and
disconnected immediately. Malfunction or short-circuits caused by metal parts may cause mortal injuries.
HEALTH HAZARD!
Never look directly into the light source, as sensitive persons may suffer an
epileptic shock (especially meant for epileptics)!
Keep away children and amateurs!
Never leave this device running unattended.

4
OPERATING DETERMINATIONS
This device is a LED moving-head lighting effect for creating decorative effects. This product is only allowed to
be operated with an alternating voltage of 100-240 V, 50/60 Hz and was designed for indoor use only.
This device is designed for professional use, e.g. on stages, in clubs, bars, theatres etc.
Lighting effects are not designed for permanent operation. Consistent operation breaks will ensure that the
device will serve you for a long time without defects.
Do not shake the device. Avoid brute force when installing or operating the device.
Never lift the fixture by holding it at the projector-head, as the mechanics may be damaged. Always hold the
fixture at the transport handles.
When choosing the installation-spot, please make sure that the device is not exposed to extreme heat,
moisture or dust. There should not be any cables lying around. Please make sure that the unit cannot be
touched or bumped.
This device must never be operated or stockpiled in surroundings where splash water, rain, moisture or fog
may harm the device. Moisture or very high humidity can reduce the insulation and lead to mortal electrical
shocks. When using smoke machines, make sure that the device is never exposed to the direct smoke jet and
is installed in a distance of 0.5 meters between smoke machine and device. The room must only be saturated
with an amount of smoke that the visibility will always be more than 10 meters.
The ambient temperature must always be between -15° C and +45° C. Keep away from direct insulation
(particularly in cars) and heaters.
The relative humidity must not exceed 50 % with an ambient temperature of 45° C.
This device must only be operated in an altitude between -20 and 2000 m over NN.
Never use the device during thunderstorms. Over voltage could destroy the device. Always disconnect the
device during thunderstorms.
The symbol
- - -m determines the minimum distance from lighted objects. The
minimum distance between light-output and the illuminated surface must be more than this value.
The device must only be installed on a non-flammable surface. In order to safeguard sufficient ventilation,
leave 50 cm of free space around the device.
The housing must never touch surrounding surfaces or objects.
Make sure that the area below the installation place is blocked when rigging, derigging or servicing the fixture.
For overhead use (mounting height >100 cm), always fix the fixture with an appropriate safety-rope. Fix the
safety-rope at the correct fixation points only. The safety-rope must never be fixed at the transport handles!
Only operate the fixture after having checked that the housing is firmly closed and all screws are tightly
fastened.
The maximum ambient temperature Ta = 45° C must never be exceeded.
Operate the device only after having become familiarized with its functions. Do not permit operation by
persons not qualified for operating the device. Most damages are the result of unprofessional operation!
Please use the original packaging if the device is to be transported.
Please consider that unauthorized modifications on the device are forbidden due to safety reasons!
Never remove the serial barcode from the device as this would make the guarantee void.
If this device will be operated in any way different to the one described in this manual, the product may suffer
damages and the guarantee becomes void. Furthermore, any other operation may lead to dangers like short-
circuit, burns, electric shock, crash etc.

5
DESCRIPTION OF THE DEVICE
Features
Source
zLight source: 7pcs Osram 15w 4in1 leds
zLed life: 60.000 hours
zLuminous Flux: 2500lumen, 15,[email protected]
zControl: Remote on/off via DMX
zBallast: switching mode power supply
Optical System
zBeam angle: 7°
X/Y
zPan: 360° (4.0 sec) or 540°(3.58 sec), Tilt: 265° (2.8 sec)
z16-bit resolution
zAuto repositioning
z3 phase motor for crazily fast and quiet movement
Features
zDMX channels: 14/22/13/15
zSuper fast, smooth and silent movement
zRGBW four colors mixing to create vivid, saturated and uniform color effect
zVirtual color wheel for color bounce
zFull range 0-100% dimmer
zVarious strobe
zRDM function to change DMX address, display flip, X/Y Reverse and so on
zSoftware upgrade via DMX
zHibernation when lost DMX for preset time
zIndicate temperature info of base, arm and lamp
zFan speed auto change according to temperature
zHeat pipe for cooling
Display
z2.4inch super nice LCD display with friendly English menu
zAuto lock
zFlip
zBack-up communicating IC
Power
zMax power consumption: 105W
zPower supply: Electronic auto-ranging
zInput voltage range: 100–240V, 50-60Hz

6
Overview
(1) Head
(2) Led
(3) Arm
(4) Base
(5) Wireless indicator
(6) Display
(7) Microphone
(8) Left button
(9) Down buttom
(10) Enter button
(11) Up button
(12) Right button
(13) Fuse holder
(14) Power input
(15) Power switch
(16) Power output
(17) 3-PIN DMX output socket
(18) 3-PIN DMX input socket
1
2
5 7
13 14 15 16 17 18

7
INSTALLATION
Rigging
The installation of the projector has to be built and constructed in a way that it can hold 10 times the weight for
1 hour without any harming deformation.
The installation must always be secured with a secondary safety attachment, e.g. an appropriate catch net.
This secondary safety attachment must be constructed in a way that no part of the installation can fall down if
the main attachment fails.
When rigging, derigging or servicing the fixture staying in the area below the installation place, on bridges,
under high working places and other endangered areas is forbidden.
The operator has to make sure that safety-relating and machine-technical installations are approved by an
expert before taking into operation for the first time and after changes before taking into operation another
time.
The operator has to make sure that safety-relating and machine-technical installations are approved by an
expert after every four year in the course of an acceptance test.
The operator has to make sure that safety-relating and machine-technical installations are approved by a
skilled person once a year.
Procedure:
The projector should be installed outside areas where persons may walk by or be seated.
IMPORTANT! OVERHEAD RIGGING REQUIRES EXTENSIVE EXPERIENCE, including (but not limited to)
calculating working load limits, installation material being used, and periodic safety inspection of all installation
material and the projector. If you lack these qualifications, do not attempt the installation yourself, but instead
use a professional structural rigger. Improper installation can result in bodily injury and.or damage to
property.
The projector has to be installed out of the reach of people.
If the projector shall be lowered from the ceiling or high joists, professional trussing systems have to be used.
The projector must never be fixed swinging freely in the room.
Caution: Projectors may cause severe injuries when crashing down! If you have doubts concerning the
safety of a possible installation, do NOT install the projector!
Before rigging make sure that the installation area can hold a minimum point load of 10 times the projector's
weight.
DANGER OF FIRE!
When installing the device, make sure there is no highly-inflammable
material (decoration articles, etc.) within a distance of min. 0.5
m.

8
CAUTION!
Use an appropriate clamp to rig the fixture on the
truss.
Follow the instructions mentionedat the bottom of the base.
Make sure that the device is fixed properly! Ensure that
the structure (truss) to which you are attaching the fixtures is
secure.
The Moving-Head can be placed directly on the stage floor or rigged in any orientation on a truss without
altering its operation characteristics (see the drawing).
The fixture’s base enables to be mounted in two ways.
For overhead use (mounting height >100 cm), always install an
appropriate safety bond.
Please note: for overhead rigging in public or industrial areas, a
series of safety instructions have to be followed that this manual
can only give in part. The operator must therefore inform
himself on the current safety instructions and consider them.
The manufacturer cannot be made liable for damages caused by incorrect installations or insufficient safety
precautions!
Install the safety bond by inserting the quick link in the hole on the bottom of the base. Pull the safety bond over
the trussing system etc. Insert the end in the quick link and tighten the fixation screw.
The maximum drop distance must never exceed 20 cm.
A safety bond which already hold the strain of a crash or which is defective must not be used again.
DANGER TO LIFE!
Before taking into operation for the first time, the installation has to be approved by an expert!

9
2 3










(1) Omega-holder
(2) Clamp
(3) Safety-rope 1
(4) Quick-lock fastener
4
Screw the clamp via a M12 screw and nut onto the Omega-holder.
Insert the quick-lock fasteners of the Omega-holder into the respective holes
on the bottom of the device. Tighten the quick-lock fasteners fully clockwise.

10
DMX-512 connection / connection between fixtures
Projector1 Projector2 Projector3
Starting address 1 Starting address 20 Starting address 39
120 Ohms DMX-512 Controller
The wires must not come contact with each other, otherwise
the fixtures will not work at all, or will not work properly.
Please note, the starting address depends upon which controller is being used.
Only use a DMX-cable and 3-pin XLR-plugs and connectors in order to connect the controller with the fixture
or one fixture with another.
Occupation of the XLR-connection:
If you are using controllers with this occupation, you can connect the DMX-output of the controller directly with
the DMX-input of the first fixture in the DMX-chain. If you wish to connect DMX-controllers with other
XLR-outputs, you need to use adapter-cables.
Building a serial
DMX-chain:
Connect the DMX-output of the first fixture in the DMX-chain with the DMX-input of the next fixture. Always
connect one output with the input of the next fixture until all fixtures are connected.
Caution: At the last fixture, the DMX-cable has to be terminated. Plug the terminator with a 120 Ωresistor
between Signal (–) and Signal (+) in the DMX-output of the last fixture.

11
Connection with the mains
Connect the device to the mains with the enclosed power supply cable.
The occupation of the connection-cablesis as follows:
Cable Pin International
Brown Live L
Blue Neutral N
Yellow/Green Earth
The earth has to be connected!
If the device will be directly connected with the local power supply network, a disconnection switch with a
minimum opening of 3 mm at every pole has to be included in the permanent electrical installation.
The device must only be connected with an electric installation carried out in compliance with the IEC-
standards. The electric installation must be equipped with a Residual Current Device (RCD) with a maximum
fault current of 30 mA.
Lighting effects must not be connected to dimming-packs.
The device is equipped with a lockable power input connector. Plug in the power cord and turn it to the right
until it locks. Plug the power cord into a grounded electrical outlet that matches the rated voltage of the
machine.
OPERATION
With the power switch, you can switch the device on and off.
After you connected the effect to the mains, the fixture starts running. During the reset, the motors are
trimmed and the device is ready for use afterwards.
Stand Alone operation
In the Stand Alone mode, the model can be used without controller.
Disconnect the fixture from the controller and call the internal program.
Please refer to the instructions under Control Board.
DMX-controlled operation
You can control the projectors individually via your DMX-controller. Every DMX-channel has a different
occupation with different features. The individual channels and their features are listed under DMX-protocol.
Addressing
The Control Board allows you to assign the DMX starting address, which is defined as the first channel from
which the fixture will respond to the controller.
If you set, for example, the address to channel 20, the fixture will use the channel 20 to 38 for control.
Please, be sure that you don’t have any overlapping channels in order to control each fixture correctly and
independently from any other fixture on the DMX-chain.
If several fixture are addressed similarly, they will work synchronically.
Press the Up/Down-buttons for setting the desired starting address. Now you can start operating the fixture via
your lighting controller.


12
Note:
After switching on, the device will automatically detect whether DMX 512 data is received or not. If
there is no data received at the DMX-input, the display will flash.
This situation can occur if:
- the XLR plug (cable with DMX signal from controller) is not connected with the input of the device.
- the controller is switched off or defective, if the cable or connector is defective or the signal wires are
swap in the input connector.
Note:
It’s necessary to insert the XLR termination plug (with 120 Ohm) in the last lighting in the link in order
to ensure proper transmission on the DMX data link.
DMX-protocol
Channel
St Ex
Ba
8bit
Ba
16bit
name function Min
DMX
Max
DMX
1 1 1 1 Pan Pan Coarse 0 255
2 2 Pan fine Pan Fine 0 255
2 3 2 3 Tilt Tilt Coarse 0 255
4 4 Tilt fine Tilt Fine 0 255
3 5 3 5 Movment
Speed fastest to Slowest 0 255
Normal 0 15
Movement With Backout 16 31
6 Movment
Function TBD 32 255
Normal Shutter Functions 0 15
Pulse-effect Forward 16 31
Pulse-effect Reverse 32 47
Random Strobe 48 63
4 7 Shutter
Function
TBD 64 255
Normal Shutter Functions
Close 0 31
Strobe Rate (slow to fast) 32 223
Open 224 255
Pulse-effect Forward
Close 0 31
Strobe Rate (slow to fast) 32 223
Open 224 255
Pulse-effect Reverse
Close 0 31
Strobe Rate (slow to fast) 32 223
Open 224 255
Random Strobe
Close 0 31
Strobe Rate (slow to fast) 32 223
5 8 Shutter
Open 224 255
Shutter closed 0 31
No function (shutter open) 32 63
Strobe effect slow to fast 64 95
No function (shutter open) 96 127
4 6 Shutter
Pulse-effect in sequences 128 159

13
No function (shutter open) 160 191
Random strobe effect slow to fast 192 223
No function (shutter open) 224 255
6 9 5 7 Dimmer Dimmer(0->100%) 0 255
10 Dimmer fine Dimmer fine control 0 255
On Function 0 15
CTC Function 16 31
Forward Spin 32 47
Reverse Spin 48 63
Continuous 64 79
Color Bounce 80 111
7 11 6 8 Virtual Color
Function
TBD 112 255
CTC Function
Colour Temperature Correction 2000K->2700K 0 223
White 3200K 224 231
White 4200K 232 239
White 5600K 240 247
White 8000K 248 255
Forward Spin
Rainbow Effect (Slow->Fast) 0 255
Reverse Spin
Rainbow Effect (Slow->Fast) 0 255
Continuous&Color Bounce
Black 0 0
Red 1 1
Green 2 2
Blue 3 3
White 4 4
Red=0, Green->up,Blue=full,White=0 5 46
Red=0, Green=full,Blue->down,White=0 47 88
Red->up, Green=full,Blue=0,White=0 89 130
Red=full, Green->down,Blue=0,White=0 131 172
Red=full, Green=0,Blue->up,White=0 173 214
8 12 7 9 Virtual
Color1
Red->down, Green=0,Blue=full,White=0 215 255
Color Bounce
Black 0 0
Red 1 1
Green 2 2
Blue 3 3
White 4 4
Red=0, Green->up,Blue=full,White=0 5 46
Red=0, Green=full,Blue->down,White=0 47 88
Red->up, Green=full,Blue=0,White=0 89 130
Red=full, Green->down,Blue=0,White=0 131 172
Red=full, Green=0,Blue->up,White=0 173 214
9 13 8 10
Virtual
Color2(Only
On Color
Bounce)
Red->down, Green=0,Blue=full,White=0 215 255
10 14 9 11 Red Red 0->100% 0 255
15 Red fine Red fine control 0 255
11 16 10 12 Green Green 0->100% 0 255

14
17 Green fine Green fine control 0 255
12 18 11 13 Blue Blue 0->100% 0 255
19 Blue fine Blue fine control 0 255
13 20 12 14 White White 0->100% 0 255
21 White fine White fine control 0 255
Normal 0 7
Reset All 8 15
Pan&Tilt Reset 16 23
TBD 24 55
Display Off 56 63
Display On 64 71
TBD 72 79
TBD 80 87
Hibernation 88 95
14 22 13 15 Control
TBD 96 255
Control Board
The Control Board offers several features: you can simply set the starting address, run the pre-programmed
program or make a reset.
The main menu is accessed by pressing Enter until the display is lit. Browse through the menu by pressing
the arrow buttons (up, down, left, right). Press Enter in order to select the desired menu. You can change the
selection by pressing the arrow buttons. Press Enter in order to confirm. The functions provided are
described in the following sections.
Defaultsettingsshaded.1BasicReload/2ProgramReload/3PrivateReload
Connect
DMXAddress①XXXDMXaddresssetting
Max
Temperature①
80~139℃,90℃/176~282℉,194℉Lampoffif
temperature
continuouslyover
for5minutes
Light
LampAdjust①PAN……Adjustvalueofeach
channels
TimeInfo.CurrentXXXX(Hours)
FixtureLifeXXXX(Hours)
Fixtureboottime
Fixturetotalrun
time
TemperatureNearLampTemp(dependsonfixture)Temperature
Sensors
FansSpeedNearLampFan(dependsonfixture)FanspeedSensors
ChannelValuePAN……Displayvalueof
channel
ErrorMessagePan,Tilt……Errorchannels
FixtureModelxxxxxxxxxxxxDisplaymodelbrand
andmodel
Information
SoftwareVer1U01V1.0.00
2U01V1.0.00
:
VersionofeachIC

15
ResetAll
Pan&Tilt
Others
Resetall
ResetPan&Tilt
ResetOthers
MovmentPanReverse①
TiltReverse①
PanDegree①
Encoders①
Pan/TiltMode①
ON/OFF
ON/OFF
630/540
ON/OFF
Stand/Smooth
PanReverse
TiltReverse
ChoosePanDegree
Encoderwheel
on/off
Choosepan/tilt
mode
UISetMicSens. ③
NoSignal①

Temperature.C/F①

FansMode①
Hibernation①
Backlight①
FlipDisplay①

DisplayBright③
BrandShow①
KeyLock①
Language①
0~99%,60%
Close/Hold/Auto/Music

Fahrenheit/Celsius

AutoSpeed/HighSpeed
OFF,01M~99M，15M
02~60m02m
ON/OFF

00~3110
ON/OFF
ON/OFF
En/简/繁/Fr/Sp
SensitivityofMic
Modewhenno
signal
Temperatureat℃/
℉
Fansmode
Sleepingmode
Showbacklighttime
Display180°
reverse
DisplayBrightness
Showbrandornot
Keylockon/off
LanguageSelect
UserMode①Standard
Extended
Basic‐8bit
Basic‐16bit
User
Standardmode
Extendedmode
Basic‐8bitmode
Basic‐16bitmode
Userprogrammode
Users
EditUser③MaxChannel=XX
PAN=CH01
:
Editusersmode
Calibration③‐Password‐
Pan…
=XXX
=XXX
Password:050
Calibratechannel
value
FixtureID③Name
‐Password‐
PIDCode
Name
Password:050
SetPIDofRDM
Set
ReloadDefaultBasicReload(①)
ProgramReload(②)
‐‐‐Password‐‐‐
PrivateReload(③)
AllReload
ON/OFF
ON/OFF
XXX
ON/OFF
ON/OFF
BasicReload
ProgramReload
Password:050
PrivateReload
AllReload
Program
Play①DMXReceive
SlaveReceive
Sequence
Music

SlaveReceive1,2,3
Master/Alone
Master/Alone
DMXReceive
Chooseslave
position
RunSequence
Musicmode

16
SelectChase②ChasePart1
ChasePart2
ChasePart3
Chase1~8Chase1
Chase1~8Chase2
Chase1~8Chase3
Selectandrunauto
program
EditChase②Chase1
:
Chase8
ChaseTest
Step01
Step64

=SCxxx
=SCxxx
Test
Beginningscene
Endingscene
EditScenes②EditScene001
~EditScene
250
Pan,Tilt,……
‐‐FadeTime‐‐
‐‐Secne
Time‐‐
DMXInput
=xxx
=xxx
=xxx

Inputmanualscene
Modifymanually
fadingtime
Modifymanually
scenetime
Inputscenefrom
exteriorcontroller
ScenesRecordScXX=>ScXXAutoInputscenes
Connect
DMX address setting
With this function, you can adjust the desired DMX-address via the Control Board.
Select “DMX Address“ by pressing Up or Down.
Press the Enter-button, adjust the DMX address by pressing Up or Down.
Press the Enter-button to confirm.
Wireless
With this function, you can enter wireless mode, then no need signal cable connection, in this mode
signal still transmitted by cable if the signal cables are connected, if want to send signal via wireless
cables must be disconnected.
Light
MaxTemperate
With this function you can set the inside temperature at which the projector will automatically switch the
LED off. Press Up or Down to select the maximum inside temperature between 80 °C and 139 °C.
Inside temperatures below 90 °C are not critical. 90 °C and more should lead to the LED being switched
off. Please note that the outside temperature should not exceed 45 °C.
Information
Time information Current
With this function, you can display the temporary running time of the device from the last power on. The
display shows “XXXX”, “X“ stands for the number of hours. The counter is reset after turning the device
off.
Fixture Life
With this function, you can display the running time of the device. The display shows “XXXX”,
“X“ stands for the number of hours.
Temperature
Near lamp Temp
With this function you can display the temperature in the projector-head in degree
Celsius/degree Fahrenheit.
...
Fan speed
With this function you can display the current fan speed. The display shows “XXXX”, “X“ stands for Hz.
Initial status
With this function, you can display with which value the respective channels will start.

17
Error channels
With this function, you can display the channel errors.
Fixture Model
With this function, you can display the model number and brand of the fixture.
Software version
With this function you can display the software version of each IC.
• Select “Software ver.” by pressing Up or Down.
• Press the Enter-button, the display shows e.g. “1U01 VX.X.XX”, “X.X.XX“ stands for the version number.
Set
Reset
With this function you can reset the device via the Control Board. You can select the different Reset-
functions by pressing Up or Down.
Movement
PAN Reverse
With this function you can reverse the PAN-movement.
TILT Reverse
With this function you can reverse the TILT-movement.
PAN degree
With this function you can select the PAN-degree.
• Select “PAN degree” by pressing Up or Down.
• Press the Enter-button, the display shows “540”.
• Press Up or Down to select the desired degree between “540” and “630”.
• Press the Enter-button to confirm.
Automatic PAN/TILT calibration
With the function "Encoders" you can calibrate the PAN/TILT movement to the correct starting position.
Adjust PAN/TILT speed
With this function you can define the PAN/TILT speed. You can select one of two different modes.
UI Set
Mic sensitivity
With this function, you can select the desired microphone sensitivity between 0 % and 99 %.
• Select “Mic Sens” by pressing Up or Down.
• Press the Enter-button.
• Press Up or Down to select the desired sensitivity.
• Press the Enter-button to confirm.
No DMX status
With the function "No Signal", you can set different modes if there is no DMX-signal.
• Select "Close, Hold, Auto or Music" by pressing Up or Down.
• Press Up or Down to select between "Close", "Hold", "Auto" or "Music".
• Press the Enter-button to confirm.
Select temperature designation
With this function you can select the temperature designation.
• Select “TemperatureC/F” by pressing Up or Down.
• Press Up or Down to select the desired degree between “Celsius” and “Fahrenheit”.
• Press the Enter-button to confirm.
Hibernation - power standby mode
With this function you can put the device in the power standby mode. This function will be automatically
activated after a predefined period of time of no DMX activity. In standby mode the lamp/LEDs and all motors
will power down if no DMX signal is sent to the fixture for a period of e. g. 15 minutes (can be user defined). The
fixture will automatically reset and return to normal operation once a DMX signal is sendet.

18
Backlight
With this function you can shut off the display after 2 to 60 minutes.
Flip Display
With this function you can flip the display by 180° for a better view when the fixture is hung from the truss or a
ceiling.
Brand Show
With this function you can show or hide the brand name 'BSL' on the display during menu
operation, but still show it after reset.
Key lock
With this function you can lock the keys of the Control Board to e.g. prevent menu tampering. If this function is
activated, the keys will be automatically locked as soon as exit the menu. In order to deactivate or temporarily
deactivate the keylock function, press the button UP-DOWN-LEFT-RIGHT-ENTER regain access to the menu
commands.
Users
User mode
With this function, you can create user defined channel orders.
Edit User
With this function, you can adjust the Preset user defined channel order.
Calibration
With this function, you can calibrate and adjust the effect wheels to their correct positions. The password for
this function is „050“.
Fixture ID
RDM
With this function you can call up various submenus via RDM.
This device is RDM ready. RDM stands for "Remote Device Management" and makes remote control of
devices connected to the DMX-bus possible. ANSI E1.20-2006 by ESTA specifies the RDM standard as an
extension of the DMX512 protocol.
Manual settings like adjusting the DMX starting address are no longer needed. This is especially useful when
the device is installed in a remote area.
RDM is integrated in DMX without influencing the connections. The RDM-data is transmitted via the standard
XLR-poles 1 and 2 – new DMX-cables are not necessary. RDM ready and conventional DMX devices can be
operated in one DMX line. The RDM protocol sends own packages in the DMX512 data feed and does not
influence conventional devices.
If DMX splitters are used and RDM control is to be used, these splitters must support RDM.
The number and type of RDM parameters depend on the (optional) RDM controller being used.
In general, the device supports the following commands and functions via RDM:


19
RDM Parameter ID's (Slot 21-22) Value
Category _Network Management
DISC_UNIQUE_BRANCH 0x0001
DISC_MUTE 0x0002
DISC_UN_MUTE 0x0003
Category -RDM Information
SUPPORTED_PARAMETERS 0x0050
PARAMETER_DESCRIPTION 0x0051
Category _Product Information
DEVICE_INFO 0x0060
DEVICE_MODEL_DESCRIPTION 0x0080
MANUFACTURER_LABEL 0x0081
DEVICE_LABEL 0x0082
FACTORY_DEFAULTS 0x0090
SOFTWARE_VERSION_LABEL 0x00C0
Category -DMX512 Setup
DMX_PERSONALITY 0x00E0
DMX_PERSONALITY_DESCRIPTION 0x00E1
DMX_START_ADDRESS 0x00F0
SLOT_INFO 0x0120
SLOT_DESCRIPTION 0x0121
Category _Sensors
SENSOR_DEFINITION 0x0200
SENSOR_VALUE 0x0201
Category _Power/Lamp Settings 0x04xx
DEVICE_HOURS 0x0400
Category -Display Settings
DISPLAY_INVERT 0x0500
Category _Configuration
PAN_INVERT 0x0600
TILT_INVERT 0x0601
Category _Control
IDENTIFY_DEVICE 0x1000
RESET_DEVICE 0x1001
Reload Default
With this function you can restore the factory settings of the device. The different settings (marked in the table)
will be set back to the default values (shaded).
Program
Play
Slave Revice
With this function, you can define the device as slave. You can choose one of three different Slave
programs. For further information see „Edit Chase”.
Sequence
With this function, you can run the internal program. You can select the desired program under “Select Chase”.
You can set the number of steps under “Edit Chase”. You can edit the individual scenes under “Edit Scenes”.
With this function, you can run the individual scenes either automatically, i.e. with the adjusted Step-Time.
The selection "Alone" means Stand Alone-mode and "Master" that the device is defined as master.
Music
With this function, you can run the internal program sound-controlled. The selection "Alone" means Stand
Alone-mode and "Master" that the device is defined as master.
Select chase for auto program
With this function, you can select the program for the Program Run.


20
Edit chase
With this function, you can edit the internal programs.
Edit scenes
With this function, you can edit the scenes of the internal programs.
Rec. Controller
The device features an integrated DMX-recorder by which you can transmit the programmed scenes from your
DMX-controller to the device. Adjust the desired scene numbers by pressing Up or Down (from – to). When
you call up the scenes at your controller, they will automatically be transmitted to the device.
Excursion:
A Master unit can send up to 3 different data groups to the Slave units, i.e. a Master unit can start 3 different
Slave units, which run 3 different programs. The Master unit sends the 3 program parts in a continuous loop.
The Slave unit receives data from the Master unit according to the group which the Slave unit was assigned to.
If e.g. a Slave unit is set to „Slave 1“ in the menu „Set to Slave“, the Master unit sends „Auto Program Part
1“ to the Slave unit. If set to „Slave 2“, the Slave unit receives „Chase Part 2“.
To start a Auto Program please proceed as follows:
1.Slave-Setting
• Select “Program” by pressing Up or Down.
• Press the Enter-button to confirm.
• Select “Slave” by pressing Up or Down.
• Press the Enter-button to confirm.
• Press Up or Down to select “Slave 1”, “Slave 2” or “Slave 3”.
• Press the Enter-button to confirm.
2. Automatic Program Run
• Select “Program” by pressing Up or Down.
• Press the Enter-button to confirm.
• Select “Sequence” by pressing Up or Down.
• Press the Enter-button to confirm.
• Press Up or Down to select “Master” or “Alone”. The selection "Alone" means Stand Alone-mode and
"Master" that the device is defined as master.
• Press the Enter-button to confirm.
3. Program for Select Chase
• Select “Edit Chase” by pressing Up or Down.
• Press the Enter-button to confirm.
• Select “Select Chase” by pressing Up or Down.
• Press the Enter-button to confirm.
• Press Up or Down to select “Chase Part 1”, “Chase Part 2” or “Chase Part 3”, and thus select which
Slave program is to be sent. Selection „Part 1“ means, that the Slave unit runs the same program as the
master units.
• Press the Enter-button to confirm.
4. Program selection for Edit Program
• Select “Edit Chase” by pressing Up or Down.
• Press the Enter-button to confirm.
• Select “Edit Chase” by pressing Up or Down.
• Press the Enter-button to confirm.
• Press Up or Down to select the desired program. With this function you can edit specific scenes into a
specific program.
• Press the Enter-button to confirm.
5. Automatic Scene Recording
• Select “Edit Chase” by pressing Up or Down.
• Press the Enter-button to confirm.
• Select “Edit scenes” by pressing Up or Down.
• Press the Enter-button to confirm.