btsr KTF/100HPS User manual

KTF/100HPS
(Constant Tension Feeder - High Performance)
YARN CONTROL SYSTEM
Operating Manual
ENGLISH
Rev. 1.0 – April 2005

KTF/100HPS – Rev. 1.0 – April 2005
Copyright - BTSR – All rights reserved.
This manual is intended for the users of KTF/100HPS yarn feeding devices. It is suggested to carefully
read the instruction reported in this manual before making the connections and use the system.
BTSR reserves the right to change at any time the contents of this manual, without notice.
For any technical or commercial problem, please contact your local BTSR dealer or call directly BTSR
customer service centre. We will be glad to meet your needs.
Thank you for your trust and good job.
The product described herein is compliant with the requirements of 89/336/EEC EMC Directive and
73/23/EEC Low Voltage Directive.
All BTSR products are covered by patents and adopt exclusive, profitable and high tech.
Solutions.
WindowsTM is a registered trademark of Microsoft Corporation
BTSR® is a registered trademark “Best Technology Study & Research” of BTSR International S.p.A.

Table of contents
KTF/100HPS - i -
TABLE OF CONTENTS
TABLE OF CONTENTSTABLE OF CONTENTS
TABLE OF CONTENTS
INTRODUCTION
The device that meets the current and future production needs ............................................................................I.1
How to use this manual ..............................................................................................................................................I.2
Symbols used ...............................................................................................................................................................I.2
Reference Documentation ..........................................................................................................................................I.2
Chapter 1 - OVERVIEW
System Components .................................................................................................................................................. 1.1
Main Characteristics of KTF/100HPS Devices ....................................................................................................... 1.1
Advantages obtained by using the KTF/100HPS devices....................................................................................... 1.2
Advantages obtained by using the SMART KTF 2000 terminal combined with KTF/100HPS ......................... 1.3
Further Advantages obtained by using a PC or Notebook Connected to the KTF/100HPS Device via
Serial Line................................................................................................................................................................... 1.3
Chapter 2 – TECHNICAL DATA AND INSTALLATION
Technical Features..................................................................................................................................................... 2.1
Installation of KTF/100HPS with KTF/PW4 Power Supply.................................................................................. 2.2
Connection of KTF/100HPS devices with KTF/PW4 power supply to the Textile Machine and
related Functions...................................................................................................................................................... 2.2
Principle of operation of INC/DEC commands ....................................................................................................... 2.3
NPN Programmable Outputs Machine Connections................................................................................................ 2.4
PNP Programmable Outputs Machine Connections ................................................................................................ 2.4
Electrical Interface of KTF/100HPS Devices.......................................................................................................... 2.4
Connection Example of a Complete System including KTF/100HPS Devices, KTF/PW4 Power Supply
and SMART KTF 2000 Terminal............................................................................................................................ 2.5
Connection Example of a Complete System including KTF/100HPS Devices, KTF/PW4 Power Supply and
Notebook with PC-LINK KTF Studio Analysis/Monitoring Software.................................................................... 2.6
Connecting Cables and Power Supply devices ........................................................................................................ 2.7
Connecting Cables and Accessories in case of Installation with KTF/PW4 Power Supply .................................... 2.7
Installation of KTF/100HPS with flat cable KTF/FLAT........................................................................................ 2.8
Connection Cables and Accessories in case of Installation with Flat Cable KTF/FLAT ........................................ 2.9
Connection Example of a Complete System including KTF/100HPS Devices External Power Supply, Flat Cable
KTF/FLAT and SMART KTF 2000 Terminal ...................................................................................................... 2.10
Connection Example of a Complete System Including KTF/100HPS Devices, Flat Cable KTF/FLAT and
Notebook with PC-LINK KTF Studio Analysis/Monitoring Software.................................................................. 2.11
Instructions for Correct Yarn Threading.............................................................................................................. 2.12
Chapter 3 – KTF/100HPS OPERATION
Operating Characteristics of KTF/100HPS Devices ............................................................................................... 3.1
Symbols shown on LCD ............................................................................................................................................ 3.2
Functions Directly Available to the Textile Machine Operator............................................................................. 3.3
1) OFFSET Execution and/or Error Reset .......................................................................................................... 3.3
2) Exclusion and Re-inclusion of a KTF/100HPS Device .................................................................................. 3.5
3) Control of Temperature and Current Absorbed by KTF/100HPS Device ...................................................... 3.5
Programming the KTF/100HPS Device................................................................................................................... 3.6
General Diagram of Simple Programming Environment......................................................................................... 3.6
Advanced Programming of KTF/100HPS Devices ................................................................................................. 3.7
General Diagram of P1÷P4 Advanced Programming Levels and Default Settings ................................................. 3.8
P1 Programming Level.............................................................................................................................................. 3.9

Table of contents
- ii - KTF/100HPS
P2 Programming Level............................................................................................................................................ 3.12
Example of Relax Tension and Relax Speed parameters interaction. 3.14
P3 Programming Level............................................................................................................................................ 3.15
Characteristics of the various working modes (Mode 00 ÷04) 3.16
P4 Programming Level............................................................................................................................................ 3.18
INC/DEC Programmable Commands ................................................................................................................... 3.19
Mode 00................................................................................................................................................................. 3.19
Mode 01................................................................................................................................................................. 3.20
Mode 02................................................................................................................................................................. 3.21
Mode 03................................................................................................................................................................. 3.21
Mode 04................................................................................................................................................................. 3.22
Specific Operation Characteristics for Mode 04................................................................................................... 3.23
Error Reset............................................................................................................................................................. 3.23
Activation of Open Collector Outputs to Drive the Solenoid Valve...................................................................... 3.23
Chapter 4 – KTF/100HPS TROUBLESHOOTING AND MAINTENANCE
Indications Provided by the Red Leds on KTF/100HPS device............................................................................. 4.1
Troubleshooting on KTF/100HPS Devices .............................................................................................................. 4.2
Useful Hints when using the KTF/100HPS device on socks or pantyhose production machines ....................... 4.4
Ordinary Maintenance .............................................................................................................................................. 4.4
Repairs........................................................................................................................................................................ 4.4

Introduction
KTF/100HPS - I.1 -
INTRODUCTION
INTRODUCTIONINTRODUCTION
INTRODUCTION
Congratulations for choosing a BTSR product.
With our KTF/100HPS yarn feeding devices, with or without the SMART KTF
2000 control unit, you got an innovative, unique solution able to offer you multiple
advantages concerning quality of your production.
The device that meets the current and future production needs
To meet the growing market requirements in terms of textile products which are
requested to be more and more technical and highly qualitative at a competitive
price, the textile industry must obviously use valuable yarns, i.e. bare or covered
elastomers.
The high cost of these raw materials and their intrinsic difficulty of use during the
production process push the textile industry to demand devices, instruments and
control systems able to guarantee a high quality level of products as well as to
strictly keep under control (and optimise) the amount of yarn used.
The BTSR KTF/100HPS control devices offer the possibility to control and adjust
with extreme accuracy the yarn feeding tension, which is the main requirement to
reach the quality and saving goals stated above.
The KTF/100HPS (Constant Tension Feeder – High Performance) devices are in
fact high precision measurement and control instruments providing a real time
display of the exact yarn tension and guaranteeing, through an accurate adjustment,
a constant yarn tension in every working condition. This occurs independently of
the speed at which the textile machine is running (either high or low speed) and the
tension is kept constant even when the yarn package tension is subject to change
due to environment conditions such as humidity, temperature, etc., or when the
yarn packages are gradually emptying during the normal working process.
It is known that the yarn tension variation, due to the progressive yarn package
emptying, considerably affect the amount of yarn used by the machine.
This decreases the quality level of the product, increases the actual yarn
consumption (thus affecting the manufacturing costs), and reduces the efficiency of
the textile machine (yarn breakage).
The KTF/100HPS devices are fully programmable and can easily be adapted to
any kind of yarn or tension adjustment. Furthermore these devices are
manufactured using very high quality and precision electronic components which
guarantee an exact display of the yarn tension as well as an accurate real-time
control of the tension itself, all features which are unique to this device.

Introduction
- I.2 - KTF/100HPS
How to use this manual
This Operation Manual is divided into 4 Chapters.
Chapter 1 – Overview describes the main features, components and the operation
principle of KTF/100HPS devices.
Chapter 2 – Technical Data and Installation gives the necessary instructions to
install the devices with or without the KTF/PW4 power supply.
Chapter 3 – KTF/100HPS Operation gives a detailed description of the necessary
operations to setup and program the KTF devices according to the application
needs.
Chapter 4 – Troubleshooting and Maintenance provides a quick guide to solving
the main failures of KTF/100HPS devices.
Symbols used
! Highlights notes, warnings and subjects to which the attention of the reader
should be directed.
Indicates a particularly sensitive situation which could have an effect
on the safety or proper operation of the system.
TENSION ERROR
All the items concerning the device programming menus, within
this manual, are always show in CAPITAL LETTERS.
Reference Documentation
For operating details about the programming/analysis and monitoring systems
available for KTF/100HPS device management, please refer to the following
BTSR manuals.
SMART KTF 2000 Manual – Rev. 2.0 – Ed. 06/2003
PC-LINK KTF Studio Manual – Rev. 1.0 – Ed. 03/2005
P1.2

Overview
KTF/100HPS - 1.1 -
1
11
1 -
--
- OVERVIEW
OVERVIEWOVERVIEW
OVERVIEW
System Components
The KTF/100HPS devices can be programmed and used either in individual and
autonomous way, or they can be connected to a control/programming SMART
KTF 2000 terminal, thus obtaining a complete system providing further levels of
analysis, adjustment, control and speed-up of production cycles, as well as
statistical data processing, particularly useful to reach the quality and saving goals
stated in the Introduction of this manual.
Moreover, using a Personal Computer or Notebook with the aid of PC-LINK KTF
Studio software running under WindowsTM environment, you can implement an
efficient analysis & monitoring system which allows you to find and correct even
the minimum critical conditions and behaviour differences among the various
devices.
Main Characteristics of KTF/100HPS Devices
The KTF/100HPS device is a high-tech digital instrument that allows setting of the
exact tension value at which you want to operate. The data setting is done through
a small three-button key-pad and a graphic LCD display.
In normal operating conditions this LCD provides a real time display of the exact
yarn tension (in grams) during manufacturing process, the yarn consumption speed
(LFA) (in m/min) and in graphical form, both the average and peak values of the
yarn tension.
In addition, the operator may display at any time the internal temperature of the
device (in °C), by pressing the Reset button.
An excessive increase of the temperature could infact indicate a wrong use of the
device; for this reason, the software on board of device performs a continuous
monitoring of the internal temperature.
If such temperature exceeds 110°C, an alarm message (ERROR °C) appears in the
graphic area of LCD, and the stop output is activated.
Thanks to a configurable safety code, all parameters can only be changed by
authorised personnel who knows such safety code.
The KTF/100HPS device may easily be programmed also using the SMART KTF
2000 terminal which, thanks to its flexibility allows programming of many devices
at a glance. Once you have chosen the desired working values on a given machine,
you will just transfer the selected setting data to the SMART KTF 2000 and then
from SMART KTF 2000 to other KTF devices installed on different machines; all
this in about 1 second (i.e. the time needed to complete the data transfer).
The KTF/100HPS is a space saving device (125 x 60 x 40 mm). This permits to
install several devices on the same machine with limited encumbrances. The device
has been designed bearing in mind not only the technological aspects, but also the
ergonomic ones. Thanks to these characteristics, the device can be perfectly fitted
within the machine structure, without compromising the machine spaces which are
usual to the operator.
The KTF/100HPS device can work with a wide range of yarns, including very thin
yarns such as bare and covered elastomers, always guaranteeing a perfect control
of yarn tension values chosen by the user, which results in a high quality of the
manufactured product.

Overview
- 1.2 - KTF/100HPS
The KTF/100HPS devices are controlled by an internal microprocessor providing great
versatility (parameters may be programmed depending on the various yarn machining
conditions).
The KTF/100HPS device considerably reduces the preparation tasks, thanks to a single
self-threading ceramic eyelet that makes the operator job easier.
The tension value displayed on KTF/100HPS’s LCD indicates the actual tension with
which the device is working. This guarantees a constant and accurate monitoring of the
working process.
Advantages obtained by using the KTF/100HPS devices
! Constant yarn tension both when the machine speed changes and when the yarn
packages gradually get empty.
! Best efficiency by eliminating the yarn breakage (tears and extratensions), and
possibility to work at the highest speed offered by the machine.
! Possibility to work with a wide range of yarn types including:
- Very thin yarns, such as bare elastomers 11/17 DTEX.
- Very difficult yarns, such as covered elastomers
- Elasticised yarns either bare or covered
- Nylon, cotton, etc.
! Yarn tension graduation capability, with 0.1 g. resolution (INC/DEC function - BTSR
Patent).
! Accurate yarn feeding speed measurement (1 to 1500 m/min) – (LFA m/min = Length
of Absorbed Yarn).
! Optimisation of yarn consumption and less difficulties to keep the correct size of
manufactured products.
! Drastic reduction of yarn consumption (8% to 15% for bare elastomers, 2% - 5% for
covered elastomers).
! Better quality of manufactured product (defect free) and drastic drop of second choice
production.
! Constant keeping of set size, independently of the yarn package emptying condition.
! Possibility to use the yarn up to the complete package emptying.
! Better machine efficiency.
! Possibility to feed the strap elastic or wrist band, guaranteeing a constant compression
(hosiery machines).
! Possibility to perform gradual compression with no limits, and with a minimum
resolution of 0.1 grams.
! Efficiency optimisation on machines that use the yarn in non-continuous mode (Start-
Stop), thanks to the possibility to draw back immediately the yarn fed in excess
(Mode 04 – BTSR Patent).
! Full control of yarn presence, even during the “LEARN” phase performed with the
SMART KTF 2000 control terminal.
(Mode 04 – BTSR Patent).
! Possibility to find the best application conditions of KTF/100HPS device: (No of coils
to be wound around the roller, ideal programming values for parameters etc), thanks
to the continuous visualization, in graphic form, of both average and peak values of
yarn tension.

Overview
KTF/100HPS - 1.3 -
Advantages obtained by using the SMART KTF 2000 Terminal
combined with KTF/100HPSs
! Using the SMART KTF 2000 terminal connected to KTF/100HPS devices you have
the possibility to develop a wide range of functions which facilitate the practical use of
the installed KTFs (immediate download and upload of data), as well as to display
fundamental data such as, yarn consumed and yarn tension.
! Possibility to create up to 99 “articles”, saving them into the Data Base for an easy
subsequent recall. Without the need to setup new parameters, these will simply be
called from the Data Base and subsequently transferred to the KTF/100HPS devices
installed on textile machine.
! Possibility to control and quickly correct the stitch adjustments, thus eliminating the
defects due to unbalanced stitch consumption.
! Possibility to identify the connected KTF/100HPSs using an automatic numbering
procedure (BTSR Patent).
! Monitoring and control possibility of the stitch consumption related to the article
under production, by means of the CONTROL function.
In CONTROL environment, a yarn consumption self learning function (LEARN) is
available (BTSR Patent). With this function you can learn the amount of yarn fed
during a sample cycle and then check that such amount is kept constant during the
subsequent cycles, within the tolerance limits (+ and -); in case of deviation from
these limits the textile machine will be stopped.
! For more details, please refer to the SMART KTF 2000 operating manual.
Further Advantages obtained by using a PC or Notebook Connected to
the KTF/100HPS Device via Serial Line
! Using the PC-LINK KTF Studio software or other application programs specifically
developed by BTSR, you will have the possibility to upgrade (via serial line) the
KTF/100HPS device firmware, without the need to physically replace the
microprocessor. In addition, the PC-LINK KTF Studio software offers several analysis
and monitoring facilities that make easier the tuning of control parameters to the
production managers.
! Possibility to display in real-time up to 4 control graphics related to as many KTF
devices.
! Possibility to display/save and print (for each graphic) up to 7 different control
parameters (work tension, min/max tension, motor torque, motor speed, inlet tension).
! Possibility to immediately check the efficiency degree of KTF devices by comparing
the yarn inlet tension (not regulated) with the outlet tension (regulated by the KTF
device).
! Possibility to check (or compare) the results obtained with two different versions of
device control firmware.
!For more details, please refer to the PC-LINK KTF Studio Operating Manual.

Overview
- 1.4 - KTF/100HPS
Page intentionally left blank

Technical data and installation
KTF100/HP - 2.1 -
2
22
2 –
––
– TECHNICAL DATA AND INSTALLATION
TECHNICAL DATA AND INSTALLATIONTECHNICAL DATA AND INSTALLATION
TECHNICAL DATA AND INSTALLATION
Technical Features
KTF/100HPS device
Power supply voltage Standard: 24 VDC ± 10% (max 1500 m/min)
Boost: 32 VDC ± 10% (max 2500 m/min)
Maximum absorption 0.5A (during normal operation)
2A (under stress)
3A (at start-up)
STOP Output NPN Open Collector, 200 mA max.
Max. voltage (INC/DEC
inputs, STOP Output)
30 Vdc
Programmable yarn tension 0.2 ÷ 100.0 gr. (resolution 0.1 gr.)
Programmable alarms 0.1 ÷ 10 sec.
Integrated keypad 3 push-buttons
2 STOP red LEDs (1 on the front side + 1 on the rear side)
Signalling With LCD graphic display
Dimensions 125 x 60 x 40 mm
Operating Temperature range 10° - 60 °C
Power supply KTF/PW4 (6 + 6 outputs)
Power supply voltage 24 Vac ± 20%
Output voltage 2 x 24 Vdc ± 5% (standard)
2 x 32 Vdc ± 5% (boost)
Max output current 2 x 20A (peak)
2 x 10A (continuous)
Dimensions 115 x 135 x 55 mm
Operating Temperature range 10° - 60 °C
Signalling 8 LEDs: POWER ON, EXC,
INC, DEC, STOP (Group 1)
INC, DEC, STOP (Group 2)
Protection 1 fuse 5 x 20 – 10A
SMART KTF 2000 Terminal
Power supply voltage 24 Vdc ± 20%
Maximum absorption 100 mA
Dimensions 135 x 95 x 40 mm
Operating Temperature range 10° - 60 °C
LCD graphic display 80 x 40 mm
Integrated Touch-pad 5 membrane buttons with integrated red LED
Protection 2 fuses 5 x 20 – 1A

Technical data and installation
- 2.2 - KTF/100HPS
Installation of KTF/100HPS with KTF/PW4 Power Supply
In this kind of installation the devices are powered through a BTSR KTF/PW4
power supply, capable of handling up to 12 KTF/100 HPSs, besides the INC/DEC
and STOP interface signals. (This is the solution typically used for hosiery
machines, etc.)
Connection of KTF/100HPS Devices with KTF/PW4 Power Supply to the Textile Machine and Related
Functions
1Connect EXC terminals ( ) to the machine Stop lamp, to exclude the KTF
alarms when the machine is not running; the EXC function also allows to
automatically reset possible alarm signaling by simply restarting the machine.

Technical data and installation
KTF100/HP - 2.3 -
2The KTF/PW4 power supply has an analogue exclusion input ( )
connectable to the machine inverter input (e.g. on MATEC machines).
The analogue exclusion input allows to exclude the KTF devices when the
machine drops under a determined number of revs/min, i.e. when it is in the
stop phase.
The KTF/PW4 power supply comes with the analogue input already calibrated
for correct operation; however you can change the triggering point of
KTF/100HPS exclusion, by adjusting the trimmer (T).
3Connect the 24VAC supply terminals to the output of TRF24 transformer.
4Connect the terminal to the machine ground potential.
5Connect the STOP output of both KTF/PW4 groups to the machine STOP
input.
6Connect (+ INC) and (+ DEC) terminals to the thread guide common positive
or solenoid valves of the machine.
7 Connect (- INC ) and (- DEC) terminals to a pair of thread guide
programmable outputs or solenoid valves, or use the outputs provided by
BTSR for KTF/TSD devices.
Activate the programmable INC/DEC outputs simultaneously with the thread
guide of yarn under control and keep the commands active for all the yarn
processing time, then deactivate the programmable INC/DEC outputs
simultaneously with the thread guide of yarn.
8
Set the jumper to position to operate in normal configuration
(recommended ) – Yarn feeding speed up to 1500 m/min.
Set the jumper to position in case of particular needs requiring
higher speed (up to 2500 m/min ).
Operating with the jumper set to “BOOST” configuration, the
operating temperature of KTF/100HPS devices is subject to
increase.
Principle of operation of INC/DEC commands
When the INC/DEC commands are active, the KTF device operates with the
tension value set in MAIN TENSION function of P1 menu, and the ERROR TENSION
alarm will be active.
When, on the contrary, the INC/DEC commands are deactivated, the KTF/100HPS
device operates with the tension value set in EXIT TENSION function of P2 menu
and the ERROR TENSION will be deactivated.
To gradually adjust the value of tension set in MAIN TENSION function of P1 menu,
once the INC/DEC command have been activated, you will have to generate INC
(increment) or DEC (decrement) pulses.
For each INC or DEC pulse, the MAIN TENSION value will be respectively
Incremented or Decremented by the amount set in INC-DEC TENSION function (last
variable of P1 menu).
! For further information on P1 ÷ P4 menu’s programmable functions, please
refer to Chapter 3 – KTF/100HPS Operation.

Technical data and installation
- 2.4 - KTF/100HPS
NPN Programmable Outputs Machine Connections
PNP Programmable Outputs Machine Connections
Electrical Interface of KTF/100HPS Devices

Technical data and installation
KTF100/HP - 2.5 -
Connection Example of a Complete System including KTF/100HPS Devices, KTF/PW4 Power Supply
and SMART KTF 2000 Terminal
Concerning all electrical systems, it is a suggested rule to ensure that the ground cable
(GND) is connected to the device support.

Technical data and installation
- 2.6 - KTF/100HPS
Connection Example of a Complete System including KTF/100HPS Devices, KTF/PW4 Power Supply
and Notebook with PC-LINK KTF Studio Analysis/Monitoring Software
(*) as alternative
Concerning all electrical systems, it is a suggested rule to ensure that the ground cable
(GND) is connected to the device support.

Technical data and installation
KTF100/HP - 2.7 -
Connection Cables and Power Supply Devices
To correctly install the KTF/100HPS devices, it is necessary to use a certain
number of connecting cables provided by BTSR.
The following table summarizes the types and lengths of the main connecting
cables, which BTSR may provide. For further details and queries about the cables
and options available, please contact your local BTSR dealer.
Connecting Cables and Accessories in case of Installation with KTF/PW4 Power Supply
8 way connection cable between KTF/100HPS and KTF/PW4
KTF/400/FE Length 400 cm
Female to female cable for connection between SMART KTF 2000
and KTF/PW4
FE/50/FEC Length 50 cm
FE/100/FEC Length 100 cm
FE/200/FEC Length 200 cm
FE/400/FEC Length 400 cm
24Vac transformers for KTF/PW4 connection
TRF24/100VA 100VA transformer for max 2 KTFs
TRF24/300VA 300VA transformer for max 8 KTFs
Power supply with INC/DEC/STOP signal handling for KTF devices
KTF/PW4 12 inputs (6 + 6)

Technical data and installation
- 2.8 - KTF/100HPS
Installation of KTF/100HPS with Flat Cable KTF/FLAT
In this type of installation, the devices are powered by an external power supply, using
a KTF/FLAT cable. (This is the solution typically used for knitting machines)
In this case the INC/DEC graduation can only be performed through a serial line.
The installation of KTF/100HPS devices with flat cable KTF/FLAT is performed
using KTF/FIX rapid clamping brackets which are secured to the back side of KTF
devices.
The KTF/FIX bracket is equipped with contact pins that penetrate the insulation layer
and establish the electrical connection with the individual wires of flat cable, thanks to
the pressure provided by a contrast screw.
The electrical connection between KTF/FIX clamping bracket and KTF/100HPS
device is provided by the KTF10/FIX cable.
The following figures show the installation procedure with KTF/100HPS with flat
cable KTF/FLAT.
Insert the flat cable KTF/FLAT !into the rapid clamping bracket
KTF/FIX "
Tighten the contrast screw #, to obtain the electrical connection
Secure the KTF/FIX bracket to the KTF/100HPS device

Technical data and installation
KTF100/HP - 2.9 -
Connect the KTF10/FIX cable $to the KTF/FIX connector
Connect the KTF10/FIX cable to the 8 pin connector of
KTF/100HPS
KTF/100HPS correctly connected to the flat cable through
KTF/FIX clamping bracket
! The flat cable support bar must have a height of 25 mm.
Connection cables and accessories in case of installation with flat cable KTF/FLAT
Flat cable KTF/FLAT for KTF/FIX
KTF/FLAT Variable length
Flat cable KTF/FLAT for KTF/FIX with connectors for KTF/PW4
connection
500/FLAT/PW4 Length 500 cm, with connector for KTF/PW4
Connection cable between KTF/100HPS and KTF/FIX
KTF 10 FIX Length 10 cm
Quick multi-connection clamping of KTF/100HPS with flat cable
KTF/FLAT
KTF/FIX Insulation pass-through rapid clamping bracket

Technical data and installation
- 2.10 - KTF/100HPS
Connection Example of a Complete System Including KTF/100HPS Devices, External Power Supply,
Flat Cable KTF/FLAT and SMART KTF 2000 Terminal
Concerning all electrical systems, it is a suggested rule to ensure that the ground cable
(GND) is connected to the device support.
KTF 10 FIX
FE/100FEC
KTF/FLAT
KTF/FIX