Buffalo WLI-UC-GN User manual

www.buffalotech.com 35010856 ver.02 v1.00
User Manual - WLI-UC-GN
Wireless N USB 2.0 Adapter/Router

2
Table of Contents
Introduction .............................................................................3
Full Installation ........................................................................4
Connect to a Wireless Network ..........................................7
Using Client Manager 3 for Windows XP ............................7
Using Client Manager V for Windows Vista ........................8
Alternate Installation (Drivers Only) ........................................ 12
Windows Zero Cong.......................................................13
Using AOSS ............................................................................14
Using WPS with Client Manager 3........................................... 17
Using WPS with Client Manager V...........................................18
Access Point/Router Mode ......................................................20
Connecting Your Nintendo DS® ..............................................22
Connecting Your Nintendo Wii®.............................................. 24
Connecting Your Sony PSP® ...................................................27
Connecting Your Sony Playstation 3® .....................................28
Specications .........................................................................31
Regulatory Compliance Information ........................................32
Logos and Trademarks............................................................44
Contact Information................................................................45
GPL Information .....................................................................47

3
Congratulations on your purchase! The WLI-UC-GN wireless USB Adapter connects your
notebook computer or desktop PC to 2.4 GHz wireless n, g, or b networks. It can also serve as
a router/access point for connecting other wireless devices to your existing network. To install
your WLI-UC-GN with all of the available software, turn to the next page. To install the WLI-UC-
GN with wireless client drivers only, turn to page 12.
Introduction

4
The installation program will install drivers, Client Manager software, a tool to switch between
client and router modes, and software to let the WLI-UC-GN act as an access point for other
wireless devices. If you only want to install wireless drivers, turn to page 12.
Do not insert the USB key into a USB port yet. Insert the WLI-UC-GN Navigator CD into the CD-
ROM drive.
Full Installation
This window will open on your desktop.
Select Begin Installation.

5
Click Install to continue. Step through the wizard to install
your software.
The WLI-UC-GN may be installed as either a wireless client
or a wireless access point.
Choose Client Mode Installation if you want to add a wireless
client to your computer, allowing it to connect to existing
wireless networks.
Choose Access Point Mode Installation if you want to
congure the WLI-UC-GN as a simple wireless access point
for connecting AOSS-compatible devices such as game
consoles.
Note: After installation, you will be easily able to switch
between the two modes.
Installation

6
Installation
During the installation, the wizard will ask you to insert,
remove, and then reinsert the WLI-UG-GN at various times.
Follow the instructions on each screen.
When the wizard is complete, click Finish.

7
Client Manager software lets you connect your computer to a wireless network. Client Manager
3 software is installed on Windows XP computers. If your computer uses Vista, turn to the next
page instead. To open Client Manager 3, click on the icon in the systray.
Click on one of the three buttons up top to navigate to the three different
sections of Client Manager. The Scan tab shows a list of available
wireless networks. Highlight one and click Connect at the bottom to
connect to that network.
The Status tab shows information about your current wireless
connection.
The Proles tab lets you create, store, and prioritize common wireless
connections. The AOSS/WPS button is also located here.
Connect to a Wireless Network: Client Manager 3 for Windows XP

8
Client Manager V will open. Click
on Prole List on the left side of
the window.
Client Manager V for Windows Vista
If your computer uses the Microsoft Vista operating system,
Client Manager V software will have been installed. To use Client
Manager V to connect to your wireless network, click on the
icon in the system tray. In the popup, click Advanced.
In Prole List, click New.

9
Now, click on the Connect Manually button.
The AOSS/WPS button is here. To congure the client
manually, click on the Advanced Setup button.

10
Highlight your network name (SSID) and click Next.
Click on the Search button.

11
Client Manager V will connect you to your wireless
network!
Enter the security type and encryption method. Enter
your network’s encryption key or password. Click
Connect.

12
If you prefer to not install Client Manager, you
may choose to install only wireless drivers. With
a drivers-only installation, you will have to use
different software, such as Windows Zero Cong,
to manage your wireless connection. See the
next page for instructions on using Windows Zero
Cong. To install only drivers, navigate to the
driver folder on your AirNavigator CD and click on
DrvSetup. Or click Start, then Run, and type d:\
driver\DrvSetup.exe into the Open window, where
“d” is the driveletter of your CD-ROM. Do not
Alternate Installation (Drivers only)
Step through the wizard to install wireless client drivers for your AirStation. Plug the AirStation
into a USB port on your computer when directed by the wizard.
connect the AirStation to your computer until directed to do so by the wizard. Click OK.

13
To use Windows’ built-in wireless utility, click on its icon in the system tray. Zero Cong will
open.
Using Windows® Zero Cong
All available wireless networks will be listed. Click on your
network to highlight it and then click Connect.
If your network requires a network key or password to
connect, enter it twice. Click Connect. When the wireless
icon in the systray changes to , you are connected to the
wireless network.

14
installed Client Manager to use AOSS with the WLI-UC-GN. Also, your router or access
point must support AOSS to use it. Start Client Manager by double-clicking on the
black antenna icon in your systray.
In Client Manager 3, the AOSS button is in the Proles section.
In Client Manager V, the AOSS button is available from the Proles List page. Click
New to get to the AOSS button.
AOSS (AirStation One-Touch Secure System) is
a simple system for connecting wireless clients
to an access point while enforcing the most
secure possible connection encryption type.
Users no longer need to worry about choosing
the proper security protocols, IP addresses,
or SSID. AOSS will determine the optimal
connection and congure it in seconds.
Your WLI-UC-GN has its AOSS button in the
Client Manager software. If your router or
access point supports AOSS, then you can
connect the WLI-UC-GN to your wireless
network easily and securely. You must have
Using AOSS

15
•Initiate AOSS by clicking the blue button on the Client Manager’s screen. A wizard will appear.
•Now, press the AOSS button on your access point. Hold it down until the AOSS LED on the
access point begins to ash (1-3 seconds).
Using AOSS

16
Once AOSS is complete (about 30 seconds), the connection is archived as a prole for later use.
Click Finish to exit the wizard. You are now connected to the network with a secure wireless con-
nection.
Notes:
AOSS will scan for an AOSS partner for about two minutes. If it times out before nding one, just
press the AOSS buttons again.
Output power is reduced to 25% of normal during AOSS for security reasons. If you’re having
trouble making an AOSS connection, temporarily move the devices closer together.
AOSS will automatically use the highest level of security available for all currently connected
wireless devices.
If you have trouble connecting with AOSS, temporarily disable all personal rewalls on your PC,
such as ZoneAlarm or Microsoft Personal Firewall. These programs may be re-enabled after
AOSS has nished. Also, make sure that any other wireless client manager software is disabled
before using Client Manager.
Using AOSS

17
WPS is a simple system for connecting wireless clients to
an access point. It works with many brands and types of
access points and wireless routers.
There are several ways to connect with WPS. One is by
clicking the WPS button for each device. The WLI-UC-GN
has its WPS button in the Client Manager software. Start
Client Manager 3 by double clicking on the black antenna
icon in your systray, or by launching it from your Start
Menu: Programs/ Buffalo/AirStation Utility/Client Manager.
The WPS button is under the Proles tab, at the bottom of
the screen. Consult your router/AP’s documentation for the
location of its WPS button.
WPS also allows connections using PIN Codes. To
generate a PIN Code from Client Manager 3, right-click
on the antenna icon in your systray and select Easy
Connection/WPS PIN code.
Using WPS with Client Manager 3

18
To connect with WPS from Client Manager V, click on the black
antenna icon in your systray. In the popup, click Advanced.
Using WPS with Client Manager V
Client Manager V will open. Click on Prole List on the left side of the
window.
In Proles List, click New.

19
Click on the WPS/AOSS button.
Now, press the WPS button on your router or access point.
WPS will automatically connect your client to the wireless
network.
Note: Consult your router or access point’s documentation
for the location of its WPS button.

20
Besides its wireless client capability, the WLI-UC-GN can
function as a wireless access point. If your computer
already has a connection to the internet, and you want
to connect AOSS-compatible devices wirelessly, then
choose Access Point Mode during installation. Note: If
you have rewall or antivirus software running on the
computer, temporarily disable it before continuing.
Disconnect your internet connection at the same time
for safety. Step through the wizard to install your WLI-
UC-GN in Access Point Mode. When you’re done, turn
on your rewall, enable your antivirus software, and
reconnect your internet connection.
You can also switch into Access Point Mode from the
Start menu, in Programs/Buffalo/AirStation Utility/
Access Point / Router Mode
Router or Client Switch Tool, or by clicking
the icon on your desktop. This tool lets you
easily switch back and forth between Client
Mode and Access Point Mode.