Bull 94008 User manual

ASSEMBLY & OPERATING INSTRUCTIONS
MODEL #94008 SEARING STATION STAINLESS STEEL, BUILT-IN, L.P. (PROPANE)
MODEL #94009 SEARING STATION STAINLESS STEEL, BUILT-IN, N.G. (NATURAL GAS)

TABLE OF CONTENTS PAGE #
SAFETY INSTRUCTIONS……………………...…………………………………………………….………………………..………………………...2
THE LOCATION FOR YOUR SEARINGSTATION…….…….………….…….….……………………….....……….…………………........2
CHECKING FOR GAS LEAKS………………………………………………………………………………………...…..……………………..2
NATURAL GAS SAFETY…………………………………….……………………….……..………………….……………….…..…….……...3
PROPANE GAS SAFETY…………………………………………………………………………………………………….….………………..4
INSTALLATION INSTRUCTIONS…………………………………………………………………………………………..………………….…….....5
SPECIFICATIONS FOR SEARING STATION STRUCTURE…………….…….….…………………………...………..……………………5
CONNECTING TO GAS SOURCE…………………………………………………..………………...…………………………………….......5
NATURAL GAS CONNECTIONS……………………………………………..….………….….….….……….…….……………………….….5
PROPANE GAS CONNECTIONS………………………………………...….……..…..….…….………….…….…...…….…….…….….......5
OUTDOOR NATURAL GAS SEARING STATION INSTALLATION SPECIFICATIONS……………….….….…..…………………..……6
OUTDOOR PROPANE GASSEARING STATION INSTALLATION SPECIFICATIONS…………………….……………..…..………….7
INSPECTING / CLEANING BURNER AND GAS VALVE ORIFICE…….…….…..…..……..…….………………..………..………...….…….…8
BURNER CLEANING.................................................................................................................................................................................8
BURNER REPLACEMENT INTO INSERT……………….…….….…….…….…….…….….…………..…...…..…...…..….….…....………9
IGNITOR / ELECTRODE CHECK…………………………………………………………………….…….……..….………….………...…….9
BURNER OPERATION CHECK………………………….………………….….….….….….….….….…..…..…..…….……….…….….……9
COOKING COMPONENT………………………………………………………………………….….…...……….……….….….…………….10
LIGHTING & OPERATING INSTRUCTIONS……………………….….…….………………...…….....….………………....…...…………..……..11
LIGHTING PROCEDURES……………………………………………………….……………..…...….….…..…......…......….…............…...11
OPERATING PROCEDURE…………………………………………………….…………..….….……………………….…….…..…...….….11
COOKING TEMPERATURES…………………………………………….…..….…..……..…….…….…..……...……………..….………….11
CLEANING & MAINTENANCE…………………………………………………………………………………………..……………..………………12
TROUBLESHOOTING………………………………...........................................................................................................................................14
IF SEARING STATION FAILS TO OPERATE PROPERLY....................................................................................................................14
FLASH BACK............................................................................................................................................................................................14
PARTS LIST………………………………………………………………………………………………………………………………......................15
EXPLODED ILLUSTRATION………………………………………………………………………….……….…….…………….….….……………16
LIMITED WARRANTY…………………………………….………….…….……….……………….…………….………...….…..…..…...…………17
- READ THE FOLLOWING INSTRUCTIONS CAREFULLY AND BE SURE YOUR SEARING STATIONIS PROPERLYINSTALLED,
ASSEMBLED AND CARED FOR. FAILURE TO FOLLOW THESEINSTRUCTIONS MAY RESULT IN SERIOUS BODILY INJURY AND/OR
PROPERTY DAMAGE. IF YOU HAVE QUESTIONS CONCERNING ASSEMBLY OR OPERATION, CONSULT YOUR DEALER, GAS
APPLIANCE SERVICE REPRESENTATIVE OR YOUR GAS COMPANY.
- NOTE TO INSTALLER:
LEAVE THESE INSTRUCTIONS WITH THE CONSUMER AFTER INSTALLATION.
- NOTE TO THE CONSUMER:
RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE.
- THIS OUTDOOR COOKING GAS APPLIANCE IS NOT INTENDED TO BE INSTALLED IN OR ON RECREATIONAL VEHICLESAND/OR
BOATS.
*FOR WARRANTY PURPOSES, PLEASE RECORD YOUR MODEL NUMBER, SERIAL NUMBER, DATE OF PURCHASE & A COPY OF YOUR
RECEIPT OR INVOICEIN THE BACK OF YOUR MANUAL ON PAGE 17.
1

SAFETY INSTRUCTIONS
This searing station must be installed in accordance with local codes or, if in an area without local codes, with the latest edition of the National Fuel
Gas Code ANSI Z223.1. In Canada, installation must conform to the standard CAN/ CGA 1-b149.1 and/or .2 (Installation Code for Gas Burning
Appliances and Equipment) and any local codes.
WARNING: Fuels used in gas or oil-fired appliances and the products of combustion of such fuels, contain chemicals known to the State of
California to cause cancer, birth defects and/or reproductive harm. This warning is issued pursuant to California Health & Safety Code Sec.
25249.6.
THE LOCATION FOR YOUR SEARING STATION
DO NOT use your searing station in garages, porches, breezeways, sheds or other enclosed areas. Your searing station is to be used
OUTDOORS ONLY, with at least 21 inches clearance from the back and side of any combustible surface. The station should not be placed under
or on top of any surface that will burn. Do not obstruct the flow of combustion and ventilation air around the housing.
PROTECT CHILDREN: Keep children away from the station during use and until the station has cooled after you are finished. Do not allow
children to operate the searing station.
CHECKING FOR GAS LEAKS
NEVER TEST FOR GAS LEAKS WHILE THE STATION IS LIT! Prior to the first use and at the beginning of each new season (or, if using LP,
whenever gas cylinder is changed),it is a must thatyou check for gas leaks. Follow these steps:
1. Make a soap solution by mixing one part liquid detergent and one part water.
2. Turn off heat control valve, and then turn on gas at source.
3. Apply the soap solution to all gas connections: bubbles will appear in the soap solution if connections are not properly sealed. Tighten or repair
as necessary.
4. If you have a gas leak that you cannot repair, turn off the gas at the source, disconnect fuel line from the station and immediately callyour dealer
and gas supplier for professional assistance.
2
FOR YOUR SAFETY...
DO NOT store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance.
DO NOT store empty or full spare gas cylinders and/or chemicals under or near this or any other appliance.
Keep the fuel hose away from hot surfaces. Protect the fuel hose from dripping grease. Avoid unnecessary twisting of the hose.
Visuallyinspect the hose prior to each use for cuts, cracks excessive wear or other damage and replace if necessary.
NEVER test for gas leaks with a lighted match or open flame.
NEVER light station with lid on or before checking to ensure burner tube is fully seated over gas valve orifice.
NEVER lean over cooking surface while lighting station. Use barbecue tools with wood handles and good quality insulated oven
mitts when operating station.
IF YOU SMELL GAS...
1. Shutoff gas to the appliance at its source.
2. Extinguish any open flame.
3. Remove station lid to release any accumulation of fumes.
4. If gas odor persists, immediately contact your gas supplier.
READ CAREFULLY BEFORE ASSEMBLY AND OPERATION OF YOUR SEARING STATION

SAFETY INSTRUCTIONS (CONT.)
NATURAL GAS SAFETY
Your natural gas searing station is designed to operate on natural gas ONLY, at a pressure of 4” water column (W.C.) regulated at the natural gas
regulator attached at the back of the station. Check with your gas utility for local gas pressure and with your local municipality for building code
requirements.
Check with your gas utility or with local building codes for instructions to install gas supply line, or call a licensed and knowledgeable installer.
It is recommended that an “ON-OFF” shutoff valve be installed at the gas supply source:
- Outdoors after gas line piping exits outside wall and before quick-disconnect or before gas line piping enters ground.
- Indoors in the branch fuel line in an accessible location near the supply line.
Pipe sealing compound or pipe thread tape of the type resistant to the action of natural gas must be used on all male pipe thread. Apply
compound or tape to at least the first three threads when making the connection.
Disconnect your station from the fuel source when the gas supply is being tested at high pressures. This appliance and its individual shutoff valve
must be disconnected from the gas supply piping system during any pressure testing of that system at pressures in excess of 1/2 psig (3.5 kPa).
Turn off your station when the gas supply is being tested at low pressures. This appliance must be isolated from the gas supply piping system by
closing its individual valve.
WARNING: The gas valve is preset at the factory to operate on LP or natural gas. If you wish to convert to a different gas type, be sure to contact
your station dealer, licensed plumber or authorized service center for further details. Conversion kits are not sold to the general public and require
a professional to perform service. Failure to properly convert a unit can cause serious injury to yourself and/or others, irreparable damage to your
searing station and void of warranty.
3
SAFETY! BEWARE OF SPIDERS
CAUTION: BURNER MUST BE INSPECTED AND CLEANED BEFORE FIRST USE.
Spiders and small insects occasionally spin webs or make nests in the burner during warehousing, transit and/or after long periods of non-use.
These webs can lead to a gas flow obstruction, which could result in a fire in and around the burner tube. This type of fire is known as “FLASH-
BACK” and can cause serious damage to your station and create an unsafe operating condition for the user. Although an obstructed burner tube
is not the only cause of “FLASH BACK” it is the most common cause, and frequent inspection and cleaning of the burner is necessary.

SAFETY INSTRUCTIONS (CONT.)
PROPANE GAS SAFETY
Your propane searing station is designed to operate on propane gas ONLY, at a pressure regulated at 11” water column (W.C.) when equipped
with the correct propane orifice on the valve and a propane regulator on the supply line regulated at the residential meter.
Your propane searing station is designed to be used with a standard 20 lb gas cylinder and must be constructed and marked in accordance with
specifications of the US Departmentof Transportation for Propane Gas Cylinders.
Always keep cylinder securely fastened in an upright position.
Never connect an unregulated propane gas cylinder to the searing station.
Do not subject propane cylinders to excessive heat.
CAUTION: Never store a propane gas cylinder inside a building or in the vicinity of any gas-burning appliance.
WARNING: The gas valve is preset at the factory to operate on LP or natural gas. If you wish to convert to a different gas type, be sure to contact
your station dealer, licensed plumber or authorized service center for further details. Conversion kits are not sold to the general public and require
a professional to perform service. Failure to properly convert a unit can cause serious injury to yourself and/or others, irreparable damage to your
searing station and void of warranty.
4
SAFETY! BEWARE OF SPIDERS
CAUTION: BURNER MUST BE INSPECTED AND CLEANED BEFORE FIRST USE.
Spiders and small insects occasionally spin webs or make nests in the burner during warehousing, transit and/or after long periods of non-use.
These webs can lead to a gas flow obstruction, which could result in a fire in and around the burner tube. This type of fire is known as “FLASH-
BACK” and can cause serious damage to your station and create an unsafe operating condition for the user. Although an obstructed burner tube
is not the only cause of “FLASH BACK” it is the most common cause, and frequent inspection and cleaning of the burner is necessary.
WARNING
•Do not store a spare or disconnected liquid propane cylinder under or near
this searing station.
•A dented or rusty liquid propane cylinder may be hazardous and should be
check by your liquid propane provider.
•Do not use a liquid propane cylinder with a damaged valve.

INSTALLATION INSTRUCTIONS
Your built-in searing station comes to you fully assembled. We strongly recommend professional installation and hookup of the searing station.
These instructions will provide you with the measurements necessary for you or your builder to construct a masonry structure to house your
outdoor searing station.
NOTE TO INSTALLER: Leave these instructions with the consumer for future reference. The searing station must be installed in accordance with
all local building codes.
SPECIFICATIONS FOR SEARING STATION STRUCTURE
1. Your choice of masonry can be used for cabinet construction for the built-in station; however it must be non-combustible material. Keep in mind
when choosing a location for your station that it should NOT be located under any overhead combustible construction. Upper and ground level
vents must be provided for combustion air on both sides of built-in cabinet. Vents on station insert must remain unobstructed to allow for
combustion air and ventilation.
2. The searing station requires a wall opening of the following dimensions: See PAGES 6 & 7 for different models.
3. Place station assembly into wall opening as shown in illustration on pages 6 & 7. The station rests on side and back edges of the station insert.
4. For propane gas LP TANK STORAGE AREA MUST BE ISOLATED FROM SEARING STATION AND VENTED.
5. Do not use any combustible materials for this construction. Minimum horizontal clearance to adjacent combustible surface from side and back of
the station must be 21 inches. A 6 inch clearance is required behind station to allow for ventilation purposes.
CONNECTING TO GAS SOURCE
Refer to the following instructions and illustrations for typical gas supply connections. We strongly suggest professional installation and hook-up of
the searing station.
IMPORTANT: Before connecting station to gas source, make sure the station control knob is in the “OFF” position.
5
NATURAL GAS CONNECTIONS
IMPORTANT: Bull Outdoor Products does not recommend the use of
any quick connect fittings or lines to the unit. Use of these types of
fittings or lines could cause low gas flow and greatly reduce the
performance of the unit.
- Pipe sealing compound or pipe thread tape of the type resistant to the
action of natural gas must be used on all male pipe thread.
- Apply compound or tape to at least the first three threads when making
the connection.
- Remove plastic cap from regulator.
- Attach stainless steel flex line 3/8” flare-female end to the regulator.
- Attached the other end of flex line to shut-off valve through a nipple.
- Attach a shut-off valve to gas supply pipe.
PERFORM GAS LEAK CHECK – REFER TO PAGE 2
PROPANE GAS CONNECTIONS
- The LP gas pressure regulator and hose assembly supplied with this unit must be used
without alteration. If this assembly needs to be replaced, use only the type 1 specified in
the parts list supplied with this unit. Use a LP tank with a type 1 cylinder valve.
- Make sure the tank is firmly secured in an upright position.
- Turn the black coupling nut of the hose and regulator assembly in a clockwise direction.
- Make sure it is completely threaded onto the cylinder valve before turning gas supply on.
PERFORM GAS LEAK CHECK – REFER TO PAGE 2
READ CAREFULLY BEFORE ASSEMBLY AND OPERATION OF YOUR SEARING STATION

INSTALLATION INSTRUCTIONS (CONT.)
OUTDOOR NATURAL GAS SEARING STATION INSTALLATION SPECIFICATIONS
NOTE:
- Vents must be provided for combustion air and ventilation on both sides of built-in cabinet.
- When choosing a location for your station keep in mind that it should never be located under any overhead combustible construction.
- The sides and back of the station should not be any closer than 21 inches to combustible construction.
-DO NOT store empty or full spare tanks under or near this or any other appliance.
- There must be a minimum of 6” counter space behind the station in order to allow for ventilation purposes.
- A 1/2” hard pipe is required connecting to the searing station NG regulator.
6

INSTALLATION INSTRUCTIONS (CONT.)
OUTDOOR PROPANE GAS SEARING STATION INSTALLATION SPECIFICATIONS
NOTE:
- Vents must be provided for combustion air and ventilation on both sides of built-in cabinet.
- When choosing a location for your station keep in mind that it should never be located under any overhead combustible construction.
- The sides and back of the station should not be any closer than 21 inches to combustible construction.
-DO NOT store empty or full spare tanks under or near this or any other appliance.
- There must be a minimum of 6” counter space behind the station in order to allow for ventilation purposes.
7

INSPECTING I CLEANING BURNER AND GAS
VALVE ORIFICE
By following these cleaning procedures on a timely basis, your station will be kept clean and working properly with minimum effort.
CAUTION – Always turn off the gas supply prior to clearing your searing station.
BURNER CLEANING
1. Remove burner from the station insert (See drawing below).
2. Using a narrow bottlebrush with a flexible handle, run itthrough the burner tube several times.
3. Inspect the burner assembly for any openings caused by corrosion.
8

INSPECTING / CLEANING BURNER AND GAS
VALVE ORIFICE (CONT.)
BURNER REPLACEMENT INTO INSERT
CAUTION – Always turn off the gas supply prior to clearing your searing station.
1. Replace burner back into the station insert. There is no need to replace the wing nut back into the cast peg, it is for shipping purposes only.
2. Check the burner for proper location after replacing. Make sure the orifice is inside of the burner tube (see drawing below). If the orifice
does not fit inside the burner tube, lighting the burner may cause explosion and/or fire.
IGNITER I ELECTRODE CHECK
With the control knob set to “OFF”, check the igniter for presence of spark at electrode. Push control knob in fully and turn slowly about a 1/4 turn to
the left (counter-clockwise) until a click is heard; the trigger hitting the strike block should produce a blue spark at the electrode tip. Return control
knob to “OFF”.
BURNER OPERATION CHECK
NOTE: Upon first assembly the gas lines and burner will be full of air. In order for the burner to light properly the lines must fill with gas. It may
require several attempts at lighting the burner before you are successful.
1. With the searing station control knob in the “OFF” position, turn on the Gas supply.
9

INSPECTING / CLEANING BURNER AND GAS
VALVE ORIFICE (CONT.)
2. Light the burner by pushing its control knob in fully and slowly (3 to 4 seconds) turning it about 1/4 turn to the left (counter-clockwise) until a click
is heard. The 3 to 4 second duration should provide enough gas to light the burner. Ifthe burner does not light, immediately return the control knob
to “OFF”, wait several minutes for the gas to disperse, and repeat the process. After burner lights successfully, turn control knob to “OFF”.
3. If the burner fails to light after several attempts, discontinue gas supply at source and re-inspectfor obstructions to gas flow and orifices.
COOKING COMPONENT
IMPORTANT: Before first use: wash cooking grid with warm, soapy water. Rinse and dry thoroughly. Season metal surfaces with cooking oil
occasionally. (After cooking is completed, turn station to high setting for NO MORE THAN five minutes to burn off excess grease or food residue).
NOW YOUR SEARING STATION IS READY TO USE!
Before first use and at the beginning of each barbecue season:
1. Please read Safety, Lighting and Operating Instructions carefully.
2. Check gas valve orifice, burner tube and burner ports for any obstructions.
3. PERFORM GAS LEAK CHECK – REFER TO PAGE 2.
10

LIGHTING & OPERATING INSTRUCTIONS
CAUTION: TO ENSURE YOUR SAFETY, DO NOT OPERATE SEARING STATION UNTILYOU FULLY READ AND UNDERSTAND THE
INSTRUCTIONS.
LIGHTING PROCEDURES
Lighting Burner:
1. Become familiar with the safety guidelines at the front of the manual. DO NOT SMOKE WHILE LIGHTING STATION OR CHECKING GAS
SUPPLY CONNECTIONS!
2. If your station fuel source is a LP gas cylinder, check to see that cylinder is filled.
3. Check that the end of the burner tube is properly located over the orifice.
4. Make sure all gas connections are securely tightened. TESTFOR LEAKS WITH A SOAP SOLUTION, NEVER WITH A FLAME. (Gas Leak
Check instructions are on page 2).
5. Always remove lid before lighting.
6. Set control knob to “OFF” and open gas supply, LP cylinder or natural gas valve.
7. To ignite the burner: Push in control knob completely and rotate slowly (3 to 4 seconds) about 1/4 turn to the left (counter clockwise) until a click
is heard. The 3 to 4 second duration should provide enough gas to light the burner. Ifthe burner does not light, immediately return the control knob
to ‘OFF’, wait several minutes for the gas to disperse, and repeat the process.
8. Adjust control knob to desired searing temperature.
NOTE: If igniter fails to produce a spark at the electrode tip, burner can be manually lit with a fireplace-type match.
NOTE: To light the station with a fireplace-type match, follow steps 1 through 6 above. Remove cooking grid and insert lighted fireplace-type
match or long-necked butane lighter placing flame near to burner ports. Press in control knob and rotate left to “HIGH” setting to release gas.
Burner should light immediately. Replace cooking grid and adjust burner to desired searing temperature.
OPERATING PROCEDURE
Burn-off: Before searing on your station for the first time, burn the station to get rid of any odors or foreign matter by igniting the burner and
operating at “HIGH” setting for about five minutes. You may then either set the control to “OFF” or sear on your station immediately by turning the
control knob to a lower setting.
CAUTION: DO NOT LEAVE SEARING STATION UNATTENDED WHILE IN USE.
Preheating: It is necessary to preheat the station for a short time before searing certain foods, depending on the type of food and the cooking
temperature. Food that requires a high cooking temperature needs to preheat for five minutes; food that requires a lower cooking temperature
needs only a period of two to three minutes.
COOKING TEMPERATURES
HIGH setting - Use this setting for searing thick cuts such as steaks and chops.
LOW setting - Use this setting for searing lean cuts such as fish.
CAUTION:
- If burner goes out during operation, close gas supply at source, and turn off gas valve. Wait five minutes before attempting to re-light (this allows
accumulated gas fumes to clear).
- Should a grease fire occur, close gas supply at source, turn off the burner and leave lid off until fire is out. Do not use water or any liquid to
extinguish a grease fire.
- Do not attempt to disconnect any gas fitting while your searing station is in operation or while gas feed is on.
- Do not allow children to operate the searing station.
- Do not place any body parts over the searing station for any period of time.
- Never pour water on or in the station at any time. 11

CLEANING & MAINTENANCE
CAUTION: ALWAYS ALLOW THE SEARING STATION TO COOL COMPLETELY BEFORE CLEANING AND DO NOT ALLOW WATER TO
GET ONTO THE BURNER SURFACE.
CLEANING THE COOKING GRID
After searing, turn control knob to “OFF” and let station cool before attempting to clean your cooking grid. Before first use and periodically it is
suggested that you wash the cooking grid in a mild soap and warm water solution. You can use a washcloth or a vegetable brush to clean your
cooking grid.
CLEANING THE BURNER
IMPORTANT: Gas control knob should be in the “OFF” position, and fuel line should be disconnected from gas valve manifold. To reduce the
chance of FLASHBACK, the procedure below should be followed at least once a month or when your station has not been used for an extended
period of time.
1. Remove burner from the station by carefully lifting the burner up and away from orifice.
2. Wire brush entire outer surface of burner to remove food residue and dirt. Clean any clogged orifices with a stiff wire such as an open paper clip.
3. Inspect the burner for damage (cracks or holes) and if such damage is found, order and install a new burner.
4. After installation, check to insure that the orifice is correctly placed inside the end of burner tube. Also check position of spark electrode.
CLEANING THE GREASE TRAY
The grease tray should be emptied and wiped down periodically and washed in a mild detergent and warm water solution. This procedure will
reduce the risk of a grease fire.
ANNUAL CLEANING OF STATION HOUSING
Burning-off the searing station after every cookout will keep it ready for instant use. However, periodically the station should be given an entire
thorough cleaning to ensure optimal performance.
1. Shut off gas supply at source and disconnect fuel line from gas valve manifold. Protect fuel line fitting.
2. Remove and clean the cooking grid as explained above.
3. Cover the gas orifice with a piece of aluminum foil.
4. Brush the inside and bottom of the station with a stiff wire brush, and wash down with a mild soap and warm water solution. Rinse thoroughly
and let dry.
5. Remove aluminum foil from the orifice and check for obstruction.
6. Check electrode as instructed on page 9.
7. Replace cooking grid.
8. Reconnect to gas source and observe burner flame for correct operation.
IMPORTANT: You should NOT line the bottom of the station housing with aluminum foil, sand or any other grease absorbent substance. Grease
will not be able to drip down into grease collector and a grease fire could occur.
STAINLESS STEEL CLEANING AND MAINTENANCE
Stainless steel is a corrosion resistant chromium/nickel alloy steel that is both durable as well as strong with an outstanding luster. The goal of your
cleaning and maintenance routine should be to keep the stainless steel’s protective chromium oxide layer intact. This is what prevents corrosion.
Contrary to popular belief, stainless steel is NOT rustproof, especially in the environment of a swimming pool. Chlorine, bromine, some fertilizers
and other elements are extremely caustic chemicals for stainless steel. These chemicals combined with heat and humidity greatly increase the
corrosiveness of these chemicals. Regular cleaning is the best way to prevent corrosion and add years of enjoyment to your Bull stainless steel
products.
SEARING BURNER
The ceramic searing burner needs to be properly maintained in order to ensure optimal performance. Cracking can occur to the ceramic which
could lead to burner failure. Listed are a few common causes of ceramic cracking:
12

CLEANING AND MAINTENANCE (CONT.)
WATER OR LIQUIDS - The ceramic surface gets extremely hot when in use; any cold water or liquid making contact to the hot surface could
cause enough pressure to crack the ceramic. Never use water or any other liquid to control a grease fire or flare-up. Never use your searing station
in the rain; rainfall could soak the ceramic burner and cause cracks. Never use any chemicals or cleaning agents on the searing burner.
SOLID OBJECTS- Be careful notto hit the ceramic burner with any solid or hard objects. This could crack or damage the burner and lead to
failure.
IMPROPER VENTILATION - To ensure that the unit functions correctly, it is imperative that hot air must be able to exit the burner. This channelnot
only allows the hot air to be transferred throughout the unit, but it also acts as a feed of oxygen preventing a flashback and possible damage to the
ceramic burner. Always leave open space on the cooking space to allow the hot air to escape (see below).
13

TROUBLESHOOTING
IF SEARING STATION FAILS TO OPERATE PROPERLY
1. Turn off gas at source, turn control knob to “OFF”, and wait five minutes before trying again.
2. Check gas supply/connections.
3. Repeat lighting procedure.
If station still fails to operate properly, TURN “OFF” GAS AT SOURCE, TURN CONTROL KNOB TO “OFF”, wait for station to cool, and check
the following:
a. Misalignment of burner tube over orifice
CORRECTION: Reposition burner tube to properly seat over orifice.
b. Obstruction in gas line
CORRECTION: Remove fuel line from the station. DO NOT SMOKE AROUND EXPOSED GAS LINE! Open gas supply for one second to blow
any obstruction from fuel line. Close off gas supply at source and reconnect fuel line to the station.
c. Plugged orifice
CORRECTION: Remove cooking grid. Remove burner from bottom of station insert by unscrewing the wing nut from beneath burner peg (Please
reference the diagram on page 9). Carefully lift the burner up and away from gas orifice. Remove the orifice from the orifice adapter using a
crescent wrench and gently clear any obstruction with a fine wire (be careful not to bend the metal flange the adapter connects to when removing
the orifice). Re-install the orifice onto the adapter, re-install burner over the orifice and seat the burner peg into mounting bracket at bottom of
station insert. There is no need to replace the wing nut, it is for shipping purposes only. Replace the cooking grid and grease tray. If an obstruction
is suspected in the gas valve or the gas valve bracket, please contact your searing station dealer or gas appliance service person for assistance.
d. Misalignment of igniter on burner
CORRECTION: Check for proper position of electrode tip. The tip of the electrode should be pointing forward toward the front and free from grease
for spark discharging. The ignition wire should be firmly connected to the valve ignition and electrode. Replace the ignition wire if the wire were
broken or cracked. With gas supply closed and the control knob set to “OFF”, check the positive igniter individually for presence of spark at
electrode. Push the control knob in fully and rotate about 1/4 turn to the left(counter-clockwise) until click is heard; the trigger hitting the strike block
should produce a blue spark at the electrode tip. Return control knob to “OFF”.
If re-ignition is necessary
While the searing station is still hot, you must wait for a minimum of five minutes before commencing to re-ignite (this allows accumulated gas
fumes to clear). If all checks/corrections have been made and station still fails to operate properly, consult your station dealer or gas appliance
service person.
FLASHBACK
When fire occurs in and around the burner tube, immediately turn off gas at its source and turn the control knob to “OFF”. Wait until the station has
cooled completely, then clean the burner tube and screen as described on page 8.
14

PARTS LIST
MODEL #94008 SEARING STATION STAINLESSSTEEL, BUILT-IN, L.P. (PROPANE)
MODEL #94009 SEARING STATION STAINLESSSTEEL, BUILT-IN, N.G. (NATURAL GAS)
HOW TO ORDER REPLACEMENT PARTS
Please refer to the parts list on this page.
To make sure you obtain the correct replacement parts for your searing station, the following information is required to assure getting the correct
part.
1. Searing station model number (see data sticker on station) and type of gas hook up.
2. Reference number of replacement part needed.
3. Description of replacement part needed.
4. Quantity of parts needed.
IMPORTANT: Use only factory authorized parts. The use of any part that is not factory authorized can be dangerous. This will also void your
warranty.
IMPORTANT: Keep this assembly and operating instruction manual for referral, and for replacement parts ordering.
CAUTION: The gas valve is preset at the factory. If you wish to convert at some later date, be sure to contact your gas supplier or searing station
dealer before making the conversion.
CAUTION: A different gas valve must be installed when converting from one type of gas to another. You will also need a data plate indicating what
type of gas the station uses.
15
REF # PARTS # QTY WARRANTY PERIOD
1 95000 11Yr
2 95001 15Yrs
3 95002 11Yr
4 95003 11Yr
5 95004 11Yr
6 95005 1Lifetime
7 16501 11Yr
8 16505 11Yr
9 95006 11Yr
10 95007 11Yr
11 95008 (LP), 95009 (NG) 1 1 Yr
12 95010 13Yrs
13 47006 11Yr
14 95011 11Yr
15 16507 11Yr
15A 16599 11Yr
16 16544 11Yr
16A 16510 11Yr
SIDEBURNER HOSE - LIQUID PROPANE MODEL ONLY
STAINLESS FLEX TUBE 8"
REGULATOR - NATURAL GAS MODEL ONLY
REGULATOR ADAPTER - NATURAL GAS MODEL ONLY
CONTROL PANEL
GREASE TRAY
DESCRIPTION
COVER LID
INSERT ASSEMBLY
ORIFICE ADAPTER
SEARING BURNER
BEZEL - MAIN BURNER
COOKING GRATE
MANIFOLD
STAINLESS FLEX TUBE 18"
ORIFICE
GAS VALVE - MAIN BURNER
3/8" T FITTING - LIQUID PROPANE MODEL ONLY
KNOB - MAIN BURNER

EXPLODED ILLUSTRATION
16

LIMITED WARRANTY
Bull Outdoor Products, Inc. warrants to the original purchaser at the original site of delivery with proof of purchase of each Outdoor Gas Grill that
when subject to normal residential use, it is free from defects in workmanship and materials for the periods specified below. This warranty excludes
grills used in rental or commercial applications. It does not apply to rust, corrosion, oxidation or discoloration, which may occur due to moisture or
overheating, unless the affected component becomes inoperable. It does not cover labor or labor related charges. There will be a shipping and
handling charge for the delivery of the warranty part(s).
Our obligation under this warranty is limited to repair or replacement, at our option, of the product during the warranty period. The extent of any
liability of Bull Outdoor Products, Inc., under this warranty is limited to repair or replacement. This warranty does not cover normal wear of parts,
damage resulting from any of the following: negligent use or misuse of the product, use on improper fuel/gas supply, use contrary to operating
instructions, or alteration by any person other than our factory service center. The warranty period is not extended by such repair or replacement.
Warranty claim procedure: If you require service or parts for your Bull grill, please contact our Warranty Service Center for factory direct
assistance. Our hours of operation are 8AM to 4 PMPST. Our phone number is [phone] and our FAX number is [phone]. Please
direct all correspondence to: Bull Outdoor Products, Inc., 2483 W. Walnut Ave., Rialto,CA 92376. ATTN: Warranty Service Center
Product repair as provided under this warranty is your exclusive remedy. Bull Outdoor Products, Inc.shall notbe liablefor any incidental or
consequential damages for breach of any express or implied warranty on its products. Except to the extent prohibited by applicable law, any
implied warranty or merchantability or fitness for a particular purpose on this product to the duration of the above warranty. Some states do not
allow the exclusion or limitation of incidental or consequential damages, or allow limitations on how long an implied warranty lasts, so the above
limitations or exclu-sions may not apply to you. This warranty gives you specific legal rights, and you may have other rights, which vary from state
to state.
Model Number
Serial Number
Date of Purchase
*Attach a copy of your receipt or invoice here*
17