Bull 30008 Quick reference guide

ASSEMBLY & OPERATING INSTRUCTIONS
MODEL #30008 SLIDE-IN DOUBLE SIDEBURNER STAINLESS STEEL, BUILT-IN, L.P. (PROPANE)
MODEL #30009 SLIDE-IN DOUBLE SIDEBURNER STAINLESS STEEL, BUILT-IN, N.G. (NATURAL GAS)

TABLE OF CONTENTS PAGE #
SAFETY INSTRUCTIONS……………………...…………………………………………………….………………………..………………………...2
THE LOCATION FOR YOUR SLIDE-IN DOUBLE SIDEBURNER……..…….….……………………….....……….…………………........2
CHECKING FOR GAS LEAKS………………………………………………………………………………………...…..……………………..2
NATURAL GAS SAFETY…………………………………….……………………….……..………………….……………….…..…….……...3
PROPANE GAS SAFETY…………………………………………………………………………………………………….….………………..4
INSTALLATION INSTRUCTIONS…………………………………………………………………………………………..………………….…….....5
SPECIFICATIONS FOR SLIDE-IN DOUBLE SIDEBURNER STRUCTURE..…..…….……………………...………..……………………5
CONNECTING TO GAS SOURCE…………………………………………………..………………...…………………………………….......5
NATURAL GAS CONNECTIONS……………………………………………..….………….….….….……….…….……………………….….5
PROPANE GAS CONNECTIONS………………………………………...….……..…..….…….………….…….…...…….…….…….….......5
OUTDOOR NATURAL GAS SLIDE-IN DOUBLESIDEBURNER INSTALLATION SPECIFICATIONS….….…….………………..……6
OUTDOOR PROPANE GASSLIDE-IN DOUBLE SIDEBURNER INSTALLATION SPECIFICATIONS………………….……...……….7
INSPECTING / CLEANING BURNERS AND GAS VALVES…………….…….…..…..……..…….………………..………..………...….…….…8
BURNER CLEANING.................................................................................................................................................................................8
BURNER REPLACEMENT INTO INSERT……………….…….….…….…….…….…….….…………..…...…..…...…..….….…....………9
IGNITER CHECK……………………………………………………………………………………….…….……..….………….………...…….9
BURNER OPERATION CHECK………………………….………………….….….….….….….….….…..…..…..…….……….…….….……9
COOKING COMPONENT………………………………………………………………………….….…...……….……….….….…………….10
LIGHTING & OPERATING INSTRUCTIONS……………………….….…….………………...…….....….………………....…...…………..……..11
LIGHTING PROCEDURES……………………………………………………….……………..…...….….…..…......…......….…............…...11
OPERATING PROCEDURE…………………………………………………….…………..….….……………………….…….…..…...….….11
CLEANING & MAINTENANCE…………………………………………………………………………………………..……………..………………12
TROUBLESHOOTING………………………………...........................................................................................................................................13
IF SLIDE-IN DOUBLE SIDEBURNER FAILS TO OPERATE PROPERLY………..................................................................................13
FLASH BACK............................................................................................................................................................................................13
PARTS LIST………………………………………………………………………………………………………………………………......................14
EXPLODED ILLUSTRATION………………………………………………………………………….……….…….…………….….….……………15
LIMITED WARRANTY…………………………………….………….…….……….……………….…………….………...….…..…..…...…………16
- READ THE FOLLOWING INSTRUCTIONS CAREFULLY AND BE SURE YOUR SLIDE-IN DOUBLE SIDEBURNER IS PROPERLY
INSTALLED, ASSEMBLED AND CARED FOR. FAILURE TO FOLLOW THESE INSTRUCTIONS MAY RESULT IN SERIOUS BODILY INJURY
AND/OR PROPERTY DAMAGE. IF YOU HAVE QUESTIONS CONCERNING ASSEMBLY OR OPERATION, CONSULT YOUR DEALER, GAS
APPLIANCE SERVICE REPRESENTATIVE ORYOUR GAS COMPANY.
- NOTE TO INSTALLER:
LEAVE THESE INSTRUCTIONS WITH THE CONSUMER AFTER INSTALLATION.
- NOTE TO THE CONSUMER:
RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE.
- THIS OUTDOOR COOKING GAS APPLIANCE IS NOT INTENDED TO BE INSTALLED IN OR ON RECREATIONAL VEHICLES AND/OR
BOATS.
*FOR WARRANTY PURPOSES, PLEASE RECORD YOUR MODEL NUMBER, SERIAL NUMBER, DATE OF PURCHASE & A COPY OF YOUR
RECEIPT OR INVOICEIN THE BACK OF YOUR MANUAL ON PAGE 16.
1

SAFETY INSTRUCTIONS
This slide-in double sideburner must be installed in accordance with local codes or, if in an area without local codes, with the latest edition of the
National Fuel Gas Code ANSI Z223.1. In Canada, installation must conform to the standard CAN/ CGA 1-b149.1 and/or .2 (Installation Code for
Gas Burning Appliances and Equipment) and any local codes.
WARNING: Fuels used in gas or oil-fired appliances and the products of combustion of such fuels, contain chemicals known to the State of
California to cause cancer, birth defects and/or reproductive harm. This warning is issued pursuant to California Health & Safety Code Sec.
25249.6.
THE LOCATION FOR YOUR SLIDE-IN DOUBLE SIDEBURNER
DO NOT use your slide-in double sideburner in garages, porches, breezeways, sheds or other enclosed areas. Your double sideburner is to
be used OUTDOORS ONLY, with at least 21 inches clearance from the back and side of any combustible surface. The double sideburner should
not be placed under or on top of any surface that will burn. Do not obstruct the flow of combustion and ventilation air around the insert.
PROTECT CHILDREN: Keep children away from the double sideburner during use and until it has cooled after you are finished. Do not allow
children to operate the double sideburner.
CHECKING FOR GAS LEAKS
NEVER TEST FOR GAS LEAKS WHILE THE SLIDE-IN DOUBLE SIDEBURNER IS LIT! Prior to the first use and at the beginning of each new
season (or, if using LP,whenever gas cylinder is changed), it is a must that youcheck for gas leaks. Follow these steps:
1. Make a soap solution by mixing one part liquid detergent and one part water.
2. Turn off heat control valves, and then turn on gas at source.
3. Apply the soap solution to all gas connections: bubbles will appear in the soap solution if connections are not properly sealed. Tighten or repair
as necessary.
4. If you have a gas leak that you cannot repair, turn off the gas at the source, disconnect fuel line from the double sideburner and immediately call
your dealer and gas supplier for professional assistance.
2
FOR YOUR SAFETY...
DO NOT store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance.
DO NOT store empty or full spare gas cylinders and/or chemicals under or near this or any other appliance.
Keep the fuel hose away from hot surfaces. Protect the fuel hose from dripping grease. Avoid unnecessary twisting of the hose.
Visuallyinspect the hose prior to each use for cuts, cracks excessive wear or other damage and replace if necessary.
NEVER test for gas leaks with a lighted match or open flame.
NEVER light double sideburner with lid on or before checking to ensure burner tube is fully seated over gas valve orifice.
NEVER lean over cooking surface while lighting the double sideburner. Use barbecue tools with wood handles and good quality
insulated oven mitts when operating double sideburner.
IF YOU SMELL GAS...
1. Shutoff gas to the appliance at its source.
2. Extinguish any open flame.
3. Remove double sideburner lid to release any accumulation of fumes.
4. If gas odor persists, immediately contact your gas supplier.
READ CAREFULLY BEFORE ASSEMBLY AND OPERATION OF YOUR SLIDE-IN DOUBLE SIDEBURNER

SAFETY INSTRUCTIONS (CONT.)
NATURAL GAS SAFETY
Your natural gas slide-in double sideburner is designed to operate on natural gas ONLY, at a pressure of 4” water column (W.C.) regulated at the
natural gas regulator that is included with the double sideburner and natural gas orifices located on the ventri tubes. Check with your gas utility for
local gas pressure and with your local municipality for building code requirements.
Check with your gas utility or with local building codes for instructions to install gas supply line, or call a licensed and knowledgeable installer.
It is recommended that an “ON-OFF” shutoff valve be installed at the gas supply source:
- Outdoors after gas line piping exits outside wall and before quick-disconnect or before gas line piping enters ground.
- Indoors in the branch fuel line in an accessible location near the supply line.
Pipe sealing compound or pipe thread tape of the type resistant to the action of natural gas must be used on all male pipe thread. Apply
compound or tape to at least the first three threads when making the connection.
Disconnect your double sideburner from the fuel source when the gas supply is being tested at high pressures. This appliance and its individual
shutoff valve must be disconnected from the gas supply piping system during any pressure testing of that system at pressures in excess of 1/2
psig (3.5 kPa).
Turn off your double sideburner when the gas supply is being tested at low pressures. This appliance must be isolated from the gas supply piping
system by closing its individual valve.
WARNING: The gas valves are preset at the factory to operate on LP or natural gas. If you wish to convert to a different gas type, be sure to
contact your slide-in double sideburner dealer,licensed plumber or authorizedservice center for further details. Conversion kits are not sold to the
general public and require a professional to perform service. Failure to properly convert a unit can cause serious injury to yourself and/or others,
irreparable damage to your double sideburner and void of warranty.
3
SAFETY! BEWARE OF SPIDERS
CAUTION: BURNERS MUST BE INSPECTED AND CLEANED BEFORE FIRST USE.
Spiders andsmall insects occasionally spin webs or make nests inthe burners during warehousing, transitand/or after long periods of non-use.
These webs can lead to a gas flow obstruction, which could result in a fire in and around the burner tubes. This type of fire is known as “FLASH-
BACK” and can cause serious damage to your double sideburner and create an unsafe operating condition for the user. Although an obstructed
burner tube is not the only cause of “FLASH BACK” it is the most common cause, and frequent inspection and cleaning of the burners is
necessary.

SAFETY INSTRUCTIONS (CONT.)
PROPANE GAS SAFETY
Your propane slide-in double sideburner is designed to operate on propane gas ONLY, at a pressure of 11” water column (W.C.) when equipped
with a propane regulator on the supply line regulated at the residential meter and propane orifices located on the ventri tubes.
Your propane double sideburner is designed to be used with a standard 20 lb gas cylinder and must be constructed and marked in accordance
with specifications of the US Department of Transportation for Propane Gas Cylinders.
Always keep cylinder securely fastened in an upright position.
Never connect an unregulated propane gas cylinder to the double sideburner.
Do not subject propane cylinders to excessive heat.
CAUTION: Never store a propane gas cylinder inside a building or in the vicinity of any gas-burning appliance.
WARNING: The gas valves are preset at the factory to operate on LP or natural gas. If you wish to convert to a different gas type, be sure to
contact your slide-in double sideburner dealer,licensed plumber or authorizedservice center for further details. Conversion kits are not sold to the
general public and require a professional to perform service. Failure to properly convert a unit can cause serious injury to yourself and/or others,
irreparable damage to your double sideburner and void of warranty.
4
SAFETY! BEWARE OF SPIDERS
CAUTION: BURNERS MUST BE INSPECTED AND CLEANED BEFORE FIRST USE.
Spiders andsmall insects occasionally spin webs or make nests inthe burners during warehousing, transitand/or after long periods of non-use.
These webs can lead to a gas flow obstruction, which could result in a fire in and around the burner tubes. This type of fire is known as “FLASH-
BACK” and can cause serious damage to your double sideburner and create an unsafe operating condition for the user. Although an obstructed
burner tube is not the only cause of “FLASH BACK” it is the most common cause, and frequent inspection and cleaning of the burners is
necessary.
WARNING
•Do not store a spare or disconnected liquid propane cylinder under or near
this slide-in double sideburner.
•A dented or rusty liquid propane cylinder may be hazardous and should be
check by your liquid propane provider.
•Do not use a liquid propane cylinder with a damaged valve.

INSTALLATION INSTRUCTIONS
Your built-in slide-in double sideburner comes to you fully assembled. We strongly recommend professional installation and hookup of the double
sideburner. These instructions will provide youwith the measurements necessary for you or your builder to construct a masonry structure to house
your outdoor double sideburner.
NOTE TO INSTALLER: Leave these instructions with the consumer for future reference. The double sideburner must be installed in accordance
with all local building codes.
SPECIFICATIONS FOR SLIDE-IN DOUBLE SIDEBURNER STRUCTURE
1. Your choice of masonry can be used for cabinet construction for the built-in double sideburner; however it must be non-combustible material.
Keep in mind when choosing a location for your double sideburner that itshould NOT be located under any overhead combustible construction.
Upper and ground level vents must be provided for combustion air on both sides of built-in cabinet. The double sideburner insert must remain
unobstructed to allow for combustion air and ventilation.
2. The double sideburner requires a wall opening of the following dimensions: See PAGES 6 & 7 for different models.
3. Place double sideburner assembly into wall opening as shown in illustration on pages 6 & 7. The double sideburner rests on side and back
edges of the insert.
4. For propane gas LP TANK STORAGE AREA MUST BE ISOLATED FROM DOUBLE SIDEBURNER AND VENTED.
5. Do not use any combustible materials for this construction. Minimum horizontal clearance to adjacent combustible surface from side and back of
the double sideburner must be 21 inches. A 6 inch clearance is required behind double sideburner to allow for ventilation purposes.
CONNECTING TO GAS SOURCE
Refer to the following instructions and illustrations for typical gas supply connections. We strongly suggest professional installation and hook-up of
the double sideburner.
IMPORTANT: Before connecting double sideburner to gas source,
make sure the double sideburner control knobs are in the “OFF” position.
5
NATURAL GAS CONNECTIONS
- Pipe sealing compound or pipe thread tape of the type resistant to the
action of natural gas must be used on all male pipe thread.
- Apply compound or tape to at least the first three threads when making
the connection.
- Remove plastic cap from regulator.
- Attach stainless steel flex line 3/8” flare-female end to the regulator.
- Attached the other end of flex line to shut-off valve through a nipple.
- Attach a shut-off valve to gas supply pipe.
PERFORM GAS LEAK CHECK – REFER TO PAGE 2
PROPANE GAS CONNECTIONS
- The LP gas pressure regulator and hose assembly supplied with this unit must be used
without alteration. If this assembly needs to be replaced, use only the type 1 specified in
the parts list supplied with this unit. Use a LP tank with a type 1 cylinder valve.
- Make sure the tank is firmly secured in an upright position.
- Turn the black coupling nut of the hose and regulator assembly in a clockwise direction.
- Make sure it is completely threaded onto the cylinder valve before turning gas supply on.
PERFORM GAS LEAK CHECK – REFER TO PAGE 2
READ CAREFULLY BEFORE ASSEMBLY AND OPERATION OF YOUR SLIDE-IN DOUBLE SIDEBURNER

INSTALLATION INSTRUCTIONS (CONT.)
OUTDOOR NATURAL GAS SLIDE-IN DOUBLE SIDEBURNER INSTALLATION SPECIFICATIONS
NOTE:
- Vents must be provided for combustion air and ventilation on both sides of built-in cabinet.
- When choosing a location for your double sideburner keep in mind that it should never be located under any overhead combustible construction.
- The sides and back of the double sideburner should not be any closer than21 inches to combustible construction.
-DO NOT store empty or full spare tanks under or near this or any other appliance.
- There must be a minimum of 6” counter space behind the double sideburner in order to allow for ventilation purposes.
- A 1/2” hard pipe is required connecting to the double sideburner NG regulator.
6

INSTALLATION INSTRUCTIONS (CONT.)
OUTDOOR PROPANE GAS SLIDE-IN DOUBLE SIDEBURNER INSTALLATION
SPECIFICATIONS
NOTE:
- Vents must be provided for combustion air and ventilation on both sides of built-in cabinet.
- When choosing a location for your double sideburner keep in mind that it should never be located under any overhead combustible construction.
- The sides and back of the double sideburner should not be any closer than21 inches to combustible construction.
-DO NOT store empty or full spare tanks under or near this or any other appliance.
- There must be a minimum of 6” counter space behind the double sideburner in order to allow for ventilation purposes.
7

INSPECTING I CLEANING BURNERS AND GAS
VALVES
By following these cleaning procedures on a timely basis, your slide-in double sideburner will be kept clean and working properly with minimum
effort.
CAUTION – Always turn off the gas supply prior to clearing your double sideburner.
BURNER CLEANING
1. Remove burner from the double sideburner insert. Make sure to remove the ignition wires from the bottom before lifting up the burners (See
drawing below).
2. Using a narrow bottlebrush with a flexible handle, run it through the burner tube several times.
3. Inspect the burner assembly for any openings caused by corrosion.
4. Inspect the burner ports and clear any clogged ports with a stiff metal wire.
8

INSPECTING / CLEANING BURNERS AND GAS
VALVES (CONT.)
BURNER REPLACEMENT INTO INSERT
CAUTION – Always turn off the gas supply prior to clearing your double sideburner.
1. Replace burners back into the double sideburner insert.
2. Check the burners for proper location after replacing. Make sure the tubes on the bottom of the burners are inside of the ventri tubes (see
drawing below). If the burner tubes are not seated inside the ventri tubes, lighting the burners may cause explosion and/or fire.
IGNITER CHECK
With the control knobs set to “OFF”, check the first igniter for presence of spark at burner. Push control knob in fully and turn slowly about a 1/4
turn to the left (counter-clockwise) until a click is heard; the trigger hitting the strike block should produce a blue spark at the igniter tip. Return
control knob to “OFF”. Check the other igniter using the same procedure.
BURNER OPERATION CHECK
NOTE: Upon first assembly the gas lines and burners will be full of air. In order for the burners to light properly the lines must fill with gas. It may
require several attempts at lighting the burners before you are successful.
1. With the double sideburner control knobs in the “OFF” position, turn on the Gas supply.
9

INSPECTING / CLEANING BURNERS AND GAS
VALVES (CONT.)
2. Light the burner by pushing its control knob in fully and slowly (3 to 4 seconds) turning it about 1/4 turn to the left (counter-clockwise) until a click
is heard. The 3 to 4 second duration should provide enough gas to light the burner. If the burner does not light, immediately return the control knob
to “OFF”, wait several minutes for the gas to disperse, and repeat the process. After burner lights successfully, turn control knob to “OFF”. Repeat
the procedure to check the other burner.
3. If the burner(s) fails to light after several attempts, discontinue gas supply at source and re-inspect for obstructions to gas flow and orifices.
COOKING COMPONENT
IMPORTANT: Before first use: wash cooking grid with warm, soapy water. Rinse and dry thoroughly. Season metal surfaces with cooking oil
occasionally. (After cooking is completed, turn station to high setting for NO MORE THAN five minutes to burn off excess grease or food residue).
NOW YOUR SLIDE-IN DOUBLE SIDEBURNER IS READY TO USE!
Before first use and at the beginning of each barbecue season:
1. Please read Safety, Lighting and Operating Instructions carefully.
2. Check gas valves, orifices, burner tubes and burner ports for any obstructions.
3. PERFORM GAS LEAK CHECK – REFER TO PAGE 2.
10

LIGHTING & OPERATING INSTRUCTIONS
CAUTION: TO ENSURE YOUR SAFETY,DO NOT OPERATE DOUBLE SIDEBURNER UNTIL YOU FULLY READ AND UNDERSTAND THE
INSTRUCTIONS.
LIGHTING PROCEDURES
Lighting Burner:
1. Become familiar with the safety guidelines at the front of the manual. DO NOT SMOKE WHILE LIGHTING DOUBLE SIDEBURNER OR
CHECKING GAS SUPPLY CONNECTIONS!
2. If your double sideburner fuel source is a LP gas cylinder, check to see that cylinder is filled.
3. Check that the burner tubes are properly seated inside the ventri tubes.
4. Make sure all gas connections are securely tightened.TEST FOR LEAKS WITH A SOAP SOLUTION,NEVER WITH A FLAME. (Gas Leak
Check instructions are on page 2).
5. Always remove lid before lighting.
6. Set control knobs to “OFF” and open gas supply, LP cylinder or natural gas valve.
7. To ignite the burner(s): Push in control knob completely and rotate slowly (3 to 4 seconds) about 1/4 turn to the left (counter clockwise) until a
click is heard. The 3 to 4 second duration should provide enough gas to light the burner. If the burner does not light, immediately return the control
knob to ‘OFF’, wait several minutes for the gas to disperse, and repeat the process.
8. Adjust control knob(s) to desired cooking temperature.
NOTE: If igniter(s) fails to produce a spark at the electrode tip, burner can be manually lit with a fireplace-type match.
NOTE: To light the double sideburner with a fireplace-type match, follow steps 1 through 6 above. Remove cooking grid and insert lighted
fireplace-type match or long-necked butane lighter placing flame near to burner ports. Press in control knob(s) and rotate left to “HIGH” setting to
release gas. Burner(s) should light immediately. Replace cooking grid and adjust burner(s) to desired cooking temperature.
OPERATING PROCEDURE
Burn-off: Before cooking on your double sideburner for the first time, burn the double sideburner to get rid of any odors or foreign matter by
igniting the burners and operating at “HIGH” setting for about five minutes. You may then either set the control to “OFF” or cook on your double
sideburner immediately by turning the control knob(s) to a lower setting.
CAUTION: DO NOT LEAVE SLIDE-IN DOUBLE SIDEBURNER UNATTENDED WHILE IN USE.
Preheating: It is necessary to preheat the double sideburner for a short time before cooking certain foods, depending on the type of food and the
cooking temperature. Food that requires a high cooking temperature needs to preheat for five minutes; food that requires a lower cooking
temperature needs only a period of two to three minutes.
11

CLEANING & MAINTENANCE
CAUTION: ALWAYS ALLOW THE SLIDE-IN DOUBLE SIDEBURNER TO COOL COMPLETELY BEFORE CLEANING.
CLEANING THE COOKING GRID
After cooking, turn control knob(s) to “OFF” and let double sideburner cool before attempting to clean your cooking grid. Before first use and
periodically it is suggested that you wash the cooking grid in a mild soap and warm water solution. You can use a washcloth or a vegetable brush
to clean your cooking grid.
CLEANING THE BURNERS
IMPORTANT: Gas control knobs should be in the “OFF” position, and fuel line should be disconnected from gas valve manifold. To reduce the
chance of FLASHBACK,the procedure below should be followed at least once a month or when your double sideburner has not been used for an
extended period of time.
1. Remove burners from the double sideburner insert by carefully lifting the burners away from the ventri tubes (refer to page 8).
2. Wire brush entire outer surface of burner to remove residue and dirt. Clean any clogged orifices and/or burner ports with a stiffwire such as an
open paper clip.
3. Inspect the burners for damage (cracks or holes) and if such damage is found, order and install a new burner.
4. After installation, check to ensure that the burner tubes are correctly placed inside the ventri tubes. Also check position of spark electrode.
ANNUAL CLEANING OF DOUBLE SIDEBURNER HOUSING
Periodically the double sideburner should be given an entire thorough cleaning to ensure optimal performance.
1. Shut off gas supply at source and disconnect fuel line from gas valve manifold. Protect fuel line fitting.
2. Remove and clean the cooking grid as explained above.
3. Cover the gas orifices with a piece of aluminum foil.
4. Brush the inside and bottom of the double sideburner with a stiff wire brush, and wash down with a mild soap and warm water solution. Rinse
thoroughly and let dry.
5. Remove aluminum foil from the orifices and check for obstruction.
6. Check igniter as instructed on page 9.
7. Replace cooking grid.
8. Reconnect to gas source and observe burner flame for correct operation.
IMPORTANT: You should NOT line the bottom of the double sideburner housing with aluminum foil, sand or any other grease absorbent
substance. A fire could occur.
STAINLESS STEEL CLEANING AND MAINTENANCE
Stainless steel is a corrosion resistant chromium/nickel alloy steel that is both durable as well as strong with an outstanding luster. The goal of your
cleaning and maintenance routine should be to keep the stainless steel’s protective chromium oxide layer intact. This is what prevents corrosion.
Contrary to popular belief, stainless steel is NOT rustproof, especially in the environment of a swimming pool. Chlorine, bromine, some fertilizers
and other elements are extremely caustic chemicals for stainless steel. These chemicals combined with heat and humidity greatly increase the
corrosiveness of these chemicals. Regular cleaning is the best way to prevent corrosion and add years of enjoyment to your Bull stainless steel
products.
12

TROUBLESHOOTING
IF SLIDE-IN DOUBLE SIDEBURNER FAILS TO OPERATE PROPERLY
1. Turn off gas at source, turn control knob(s) to “OFF”, and wait five minutes before trying again.
2. Check gas supply/connections.
3. Repeat lighting procedure.
If double sideburner still fails to operate properly, TURN “OFF” GAS AT SOURCE, TURN CONTROL KNOBS TO “OFF”, wait for double
sideburner to cool, and check the following:
a. Misalignment of burner tube(s) over ventri tube(s)
CORRECTION: Reposition burner tube(s) to properly seat inside ventri tube(s).
b. Obstruction in gas line
CORRECTION: Remove fuel line from the double sideburner. DO NOT SMOKE AROUND EXPOSED GAS LINE! Open gas supply for one second
to blow any obstruction from fuel line. Close off gas supply at source and reconnect fuel line to the double sideburner.
c. Plugged orifice
CORRECTION: Remove the orifice from the ventri tube and gently clear any obstruction with a fine wire. Re-install the orifice onto ventri tube. If an
obstruction is suspected in the gas valve or the ventri tube, please contact your slide-in double sideburner dealer or gas appliance service person
for assistance.
d. Misalignment of igniter on burner
CORRECTION: Check for proper position of igniter tip. The tip of the igniter should be relatively close to the burner ports and free from grease for
spark discharging. The ignition wire should be firmly connected to the valve ignition and igniter. Replace the ignition wire if the wire were broken or
cracked. With gas supply closed and the control knobs set to “OFF”, check the positive igniter individually for presence of spark at igniter tip. Push
the control knob in fully and rotate about 1/4 turn to the left (counter-clockwise) until click is heard; the trigger hitting the strike block should produce
a blue spark at the igniter tip. Return control knob to “OFF”.
If re-ignition is necessary
While the double sideburner is still hot, you must wait for a minimum of five minutes before commencing to re-ignite (this allows accumulated gas
fumes to clear). If all checks/corrections have been made and the double sideburner still fails to operate properly, consult your double sideburner
dealer or gas appliance service person.
FLASHBACK
When fire occurs in and around the burner tube(s), immediately turn off gas at its source and turn the control knob(s) to “OFF”. Wait until the
double sideburner has cooled completely, then clean the burner tube(s) as described on page 8.
13

PARTS LIST
MODEL #30008 SLIDE-IN DOUBLE SIDEBURNER STAINLESS STEEL, BUILT-IN, L.P. (PROPANE)
MODEL #30009 SLIDE-IN DOUBLE SIDEBURNER STAINLESS STEEL, BUILT-IN, N.G. (NATURAL GAS)
HOW TO ORDER REPLACEMENT PARTS
Please refer to the parts list on this page.
To make sure you obtain the correctreplacement parts for your slide-in double sideburner, the following information is required to assure getting
the correct part.
1. Slide-in double sideburner model number (see data sticker on double sideburner) and type of gas hook up.
2. Reference number of replacement part needed.
3. Description of replacement part needed.
4. Quantity of parts needed.
IMPORTANT: Use only factory authorized parts. The use of any part that is not factory authorized can be dangerous. This will also void your
warranty.
IMPORTANT: Keep this assembly and operating instruction manual for referral, and for replacement parts ordering.
CAUTION: The gas valve is preset at the factory. If you wish to convert at some later date, be sure to contact your gas supplier or double
sideburner dealer before making the conversion.
CAUTION: A different gas valve must be installed when converting from one type of gas to another. You will also need a data plate indicating what
type of gas the station uses.
14
REF # PARTS # QTY WARRANTY PERIOD
1 95000 11Yr
2 30010 15Yrs
3 30011 11Yr
4 60108 23Yrs
5 95005 1 Lifetime
6 16501 21Yr
7 16505 21Yr
8 16526 21Yr
9 30012 13Yrs
10 47006 21Yr
11 95011 11Yr
12 30013 11Yr
13 30014 11Yr
14 30015 21Yr
15 30016 LP/30017 NG 21Yr
16 30018 21Yr
17 16507 11Yr
17A 16544 11Yr
18 16599 11Yr
18A 16510 11Yr
REGULATOR ADAPTER - NATURAL GAS MODEL ONLY
GAS VALVE - BURNER
KNOB - MAIN BURNER
MANIFOLD
BRASS BURNER
BEZEL - MAIN BURNER
COOKING GRATE
STAINLESS FLEX TUBE 8"
IGNITION WIRE (SHORT)
STAINLESS FLEX TUBE 18"
TEE FITTING - LIQUID PROPANE MODEL ONLY
NG REGULATOR - NATURAL GAS MODEL ONLY
IGNITION WIRE (LONG)
VENTRI TUBE
VENTRI TUBE BRASS CAP
SIDEBURNER LP HOSE - LIQUID PROPANE MODEL ONLY
ORIFICE
CONTROL PANEL
DESCRIPTION
COVER LID
INSERT ASSEMBLY

EXPLODED ILLUSTRATION
15

LIMITED WARRANTY
Bull Outdoor Products, Inc. warrants to the original purchaser at the original site of delivery with proof of purchase of each Outdoor Gas Grill that
when subject to normal residential use, it is free from defects in workmanship and materials for the periods specified below. This warranty excludes
grills used in rental or commercial applications. It does not apply to rust, corrosion, oxidation or discoloration, which may occur due to moisture or
overheating, unless the affected component becomes inoperable. It does not cover labor or labor related charges. There will be a shipping and
handling charge for the delivery of the warranty part(s).
Our obligation under this warranty is limited to repair or replacement, at our option, of the product during the warranty period. The extent of any
liability of Bull Outdoor Products, Inc., under this warranty is limited to repair or replacement. This warranty does not cover normal wear of parts,
damage resulting from any of the following: negligent use or misuse of the product, use on improper fuel/gas supply, use contrary to operating
instructions, or alteration by any person other than our factory service center. The warranty period is not extended by such repair or replacement.
Warranty claim procedure: If you require service or parts for your Bull grill, please contact our Warranty Service Center for factory direct
assistance. Our hours of operation are 8AM to 4 PMPST. Our phone number is [phone] and our FAX number is [phone]. Please
direct all correspondence to: Bull Outdoor Products, Inc., 2483 W. Walnut Ave., Rialto,CA 92376. ATTN: Warranty Service Center
Product repair as provided under this warranty is your exclusive remedy. Bull Outdoor Products,Inc. shall not be liable for any incidental or
consequential damages for breach of any express or implied warranty on its products. Except to the extent prohibited by applicable law, any
implied warranty or merchantability or fitness for a particular purpose on this product to the duration of the above warranty. Some states do not
allow the exclusion or limitation of incidental or consequential damages, or allow limitations on how long an implied warranty lasts, so the above
limitations or exclu-sions may not apply to you. This warranty gives you specific legal rights, and you may have other rights, which vary from state
to state.
Model Number
Serial Number
Date of Purchase
*Attach a copy of your receipt or invoice here*
16