Bush BSH60BFCHI User manual

Instruction Manual
GAS HOB
BSH60BFCHI
BSH60BFCHB
BSH60CIHI

2
If you require any technical guidance or find that your product is not operating as intended, a simple solution can often be found in the Troubleshooting section of these instructions,
You’ll soon be enjoying your new Gas Hob. It all begins
here, with your instructions. Don’t worry, there’s nothing
too technical coming up. Just simple, step-by-step
guidance to get you up and running quickly. Sound
good? Then let’s get started.
Help and Guidance
We’re here to help you get the most from your <enter product name>. Should you require
any guidance, a simple solution can often be found online at:
www.bush-support.com
If you still require further assistance, call one of our experts on 0345 257 7271.
.

3
or online at www.bush-support.com If you still require further assistance, call one of our experts on 345 257 7271.
Contents
Safety information
Safety information 6
Energy Saving Tips 9
Getting to know your gas hob
Ready? Let’s begin 12
Control Panel 13
Installing your gas hob
Locating your built-in hob 16
Electrical connection of your hob 20
Usage
Use of Product 24
Care and Maintenance
Cleaning 28
Product support
Troubleshooting 34
Help and assistance 35
Declaration of conformance to product
standards 36
Disposal 36
Guarantee 37
1
2
3
4
5
6

1
Safety information

Safety information
Important - Please read these instructions fully before
installing or operating
Safety information6
If you require any technical guidance or find that your product is not operating as intended, a simple solution can often be found in the Troubleshooting section of these instructions,
SAFETY INSTRUCTIONS
• Carefully read all instructions
before using your appliance and
keep them in a convenient place
for reference when necessary.
This manual has been prepared
for more than one model
therefore your appliance may
not have some of the features
described within. For this reason,
it is important to pay particular
attention to any figures whilst
reading the operating manual.
General Safety Warnings
• This appliance can be used
by children aged from 8 years
and above and by persons with
reduced physical, sensory or
mental capabilities or lack of
experience and knowledge if they
have been given supervision or
instruction concerning use of
the appliance in a safe way and
understand the hazards involved.
Children should not play with
the appliance. Cleaning and user
maintenance should not be made
by children without supervision.
WARNING: The appliance and its
accessible parts become hot during
use. Care should be taken to avoid
touching heating elements. Keep
children less than 8 years of age
away unless they are continually
supervised.
WARNING: Unattended
cooking on a hob with fat or oil can
be dangerous and may result in fire.
NEVER try to extinguish such a fire
with water, but switch cover the
flame with a lid or a fire blanket.
CAUTION: The cooking process
has to be supervised. A short term
cooking process has to be
supervised continuously
WARNING: Danger of fire: Do
not store items on the cooking
surfaces.
WARNING: If the surface is
cracked, switch off the appliance to
avoid the possibility of electric
shock.
• For models which incorporate
a hob lid, clean any spillages off
the lid before use and allow the
cooker to cool before closing the
lid.
• Do not operate the appliance by
means of an external timer or
separate remote-control system.
• Do not use harsh abrasive cleaners
or scourers to clean oven surfaces.
They can scratch the surfaces
which may result in shattering
of the door glass or damage to
surfaces.
• Do not use steam cleaners to
clean the appliance.
• Your appliance is produced in
accordance with all applicable
local and international standards
and regulations.
• Maintenance and repair work
should only be carried out by
authorised service technicians.
Installation and repair work that
is carried out by unauthorised
technicians may be dangerous.

Safety information
Important - Please read these instructions fully before
installing or operating
Safety information 7
or online at www.bush-support.com If you still require further assistance, call one of our experts on 345 257 7271.
Do not alter or modify the
specifications of the appliance in
any way. Inappropriate hob guards
can cause accidents.
• Before connecting your appliance,
make sure that the local
distribution conditions (nature
of the gas and gas pressure or
electricity voltage and frequency)
and the specifications of the
appliance are compatible. The
specifications for this appliance
are stated on the label.
CAUTION: This appliance is
designed only for cooking food and
is intended for indoor domestic
household use only. It should not be
used for any other purpose or in any
other application, such as for non-
domestic use, in a commercial
environment or for heating a room.
This appliance is not connected to a
ventilation device. It shall be installed
and connected in accordance with
current installation regulations.
Particular attention should be
given to the relevant requirements
regarding ventilation.
If the burner has not lit after 15
seconds, stop operating the device
and open the compartment door.
Wait at least 1 minute before
attempting to ignite the burner
again.
These instructions are only valid if
the correct country symbol appears
on the appliance. If the symbol
does not appear on the appliance,
refer to the technical instructions
which describe how to modify the
appliance to match the conditions of
use of the country.
All possible measures have been
taken to ensure your safety. Since
the glass may break, care should be
taken when cleaning. Avoid hitting or
knocking the glass with accessories.
Make sure that the supply cord is
not trapped or damaged during
installation. If the supply cord is
damaged, it must be replaced by the
manufacturer, its service agent or
similarly qualified persons in order to
prevent a hazard.
If your appliance is provided with a
cooking hotplate made of glass or
glass ceramic:
CAUTION: “In case of hotplate
glass breakage”:
- immediately shut off all burners
and any electrical heating elements
and isolate the appliance from the
power supply,
- do not touch the appliance
surface,
- do not use the appliance.
• Please keep children and animals
away from this appliance.
• Installation Warnings
• Do not operate the appliance
before it is fully installed.
• The appliance must be installed
by an authorised technician. The
manufacturer is not responsible
for any damage that might be
caused by defective placement
and installation by unauthorised
people.

Safety information
Important - Please read these instructions fully before
installing or operating
Safety information8
If you require any technical guidance or find that your product is not operating as intended, a simple solution can often be found in the Troubleshooting section of these instructions,
• When the appliance is unpacked,
make sure that it has not been
damaged during transportation. In
the case of a defect do not use the
appliance and contact a qualified
service agent immediately. The
materials used for packaging
(nylon, staplers, styrofoam, etc.)
may be harmful to children and
they should be collected and
removed immediately.
• Protect your appliance from the
atmosphere. Do not expose it to
sun, rain, snow, dust or excessive
humidity.
• Materials around the appliance
(i.e. cabinets) must be able to
withstand a minimum temperature
of 100°C.
• The temperature of the bottom
surface of the hob may rise during
operation, therefore a board
must be installed underneath the
product.
During Use
• Do not put flammable or
combustible materials in or near
the appliance while it is operating.
Do not leave the cooker
unattended when cooking with solid
or liquid oils. They may catch fire
under extreme heating conditions.
Never pour water on to flames that
are caused by oil, instead switch the
cooker off and cover the pan with its
lid or a fire blanket.
• Always position pans over the
centre of the cooking zone, and
turn the handles to a safe position
so they cannot be knocked or
grabbed.
• If the product will not be used for
a long period of time, turn the
main control switch off. Turn the
gas valve off when a gas appliance
is not in use.
• Make sure the appliance control
knobs are always in the “0” (stop)
position when the appliance is not
in use.
CAUTION: The use of a gas
cooking appliance results in the
production of heat, moisture and
products of combustion in the room
in which it is installed. Ensure that
the kitchen is well ventilated
especially when the appliance is in
use. Keep natural ventilation holes
open or install a mechanical
ventilation device (mechanical
extractor hood).
Prolonged intensive use of the
appliance may call for additional
ventilation, such as opening a
window, or for more effective
ventilation, for example, increasing
the level of mechanical ventilation
where necessary.
During Cleaning and Maintenance
• Make sure that your appliance is
switched off at the mains before
carrying out any cleaning or
maintenance operations.
• Do not remove the control knobs
to clean the control panel.
• To maintain the efficiency and
safety of your appliance, we
recommend you always use

Safety information
Important - Please read these instructions fully before
installing or operating
Safety information 9
or online at www.bush-support.com If you still require further assistance, call one of our experts on 345 257 7271.
original spare parts and to call our
authorised service agents when
needed.
Information related to transport
If you need any transport; keep the original case of
product and carry it with its original case when needed
to be carried. Follow the transport signs on packaging.
Tape the cooker on upper parts, caps and crowns and
pan supports to the cooking panels. Place a paper
between the upper cover and cooking panel, cover
the upper cover, then tape it to the side surfaces of
oven. Tape cardboard or paper onto the front cover on
interior glass of oven as it will be suitable to the trays,
for the wire grid in your oven not to damage to the
oven door during transport. Also tape the oven door to
the side panels.
If you do not have the original packaging; prepare a
carriage box so that the appliance, especially external
surfaces (glass and painted surfaces) of oven is
protected against external threats.
Energy Saving Tips
Hob
• Use cookwares having flat base.
• Use cookwares with proper size .
• Use cookwares with lid.
• Minimize the amount of liquid or fat.
• When liquid starts boiling , reduce the setting.

Getting to know your
gas hob 2

Getting to know your gas hob
You’ll be up and running in no time
Getting to know your gas hob
12
If you require any technical guidance or find that your product is not operating as intended, a simple solution can often be found in the Troubleshooting section of these instructions,
Ready? Let’s begin...
Please read these instructions carefully. They contain
important information which will help you get the
best from your Gas Hob and ensure safe and correct
installation and operation.
If you require any further assistance, our technical
experts are happy to help. For full details, refer to
the product support section at the end of these
instructions.

Getting to know your gas hob
You’ll be up and running in no time
Getting to know your gas hob 13
or online at www.bush-support.com If you still require further assistance, call one of our experts on 345 257 7271.
1. Gas Burner
2. Control Panel
2
1

3
Installing your gas hob

Installing your gas hob
Bringing it all together
Installing your gas hob
16
If you require any technical guidance or find that your product is not operating as intended, a simple solution can often be found in the Troubleshooting section of these instructions,
WARNING: This appliance must be installed by
an authorised service person or qualified
technician, according to the instructions in this guide
and in compliance with the current local regulations.
• Incorrect installation may cause harm and
damage, for which the manufacturer accepts no
responsibility and the warranty will not be valid.
• Prior to installation, ensure that the local distribution
conditions (electricity voltage and frequency and/
or nature of the gas and gas pressure) and the
adjustments of the appliance are compatible. The
adjustment conditions for this appliance are stated
on the label.
• The laws, ordinances, directives and standards in
force in the country of use are to be followed (safety
regulations, proper recycling in accordance with the
regulations, etc.).
Instructions for the Installer
Ventilation requirements
• For rooms with a volume of less than 5 m3,
permanent ventilation of 100 cm2free area is
required.
• For rooms with a volume of between 5 m3and 10
m3, permanent ventilation of 50 cm2free area will
be required, unless the room has a door which
opens directly to outside air in which case no
permanent ventilation is required.
• For rooms with a volume greater than 10 m3, no
permanent ventilation is required.
Important: Regardless of room size, all rooms
containing the appliance must have direct access
to outside air via an openable window or equivalent.
Emptying of burned gases from the environment
Gas appliances expel burned gas waste to the outside
air, either directly or via a cooker hood with a chimney.
If it is not possible to install a cooker hood, install a fan
on the window or wall that has access to fresh air. The
fan must have the capacity to change the volume of air
in the kitchen a minimum of 4-5 times per hour.
Air inlet section min.
100 cm2
Air inlet section
min. 100 cm2
HOB
HOB
Air inlet section
min. 100 cm2
Air inlet section
min. 100 cm2
Cooker
hood
flue
Electrical ventilator
HOB
HOB
General instructions
• After removing the packaging material from the
appliance and its accessories, ensure that the
appliance is not damaged. If you suspect any
damage, do not use it and contact an authorised
service person or qualified technician immediately.
• Make sure that there are no flammable or
combustible materials in the close vicinity, such as
curtains, oil, cloth etc. which may catch fire.
• The worktop and furniture surrounding the
appliance must be made of materials resistant to
temperatures above 100°C.
• If a cooker hood or cupboard is to be installed
above the appliance, the safety distance between
cooktop and any cupboard/cooker hood should be
as shown in the figure below.

Installing your gas hob
Bringing it all together
Installing your gas hob 17
or online at www.bush-support.com If you still require further assistance, call one of our experts on 345 257 7271.
HOB
Minimum
42 cm Minimum
42 cm
Minimum
65 cm (with
hood)
Minimum 70
cm (without
hood)
• The appliance should not be installed directly above
a dishwasher, fridge, freezer, washing machine or
clothes dryer.
• If the base of the appliance is accessible by hand, a
barrier made from a suitable material must be fitted
below the base of the appliance, ensuring that there
is no access to the base of the appliance.
• The appliance can be placed close to other
furniture on condition that, in the area where the
appliance is set up, the furniture’s height does not
exceed the height of the cooktop.
Installation of the Hob
The appliance is supplied with an installation kit
including adhesive sealing material, fixing brackets and
screws.
• Cut the aperture dimensions as indicated in the
figure. Locate the aperture on the worktop so that,
after the hob is installed, the following requirements
are followed.
B (mm) 580 min. A (mm) 50
T (mm) 515 min. C (mm) 50
H (mm) 42 min. E (mm) 500
C1 (mm) 560 min. F (mm) 10
C2 (mm) 490 G (mm) 20
D (mm) 50 I (mm) 25
J (mm) 5
B
T
C2
A
C
C1
H
F
HOB
G
I
J

Installing your gas hob
Bringing it all together
Installing your gas hob
18
If you require any technical guidance or find that your product is not operating as intended, a simple solution can often be found in the Troubleshooting section of these instructions,
I
J
Separator Separator
F
HOB
B
D
E
T
C2
A
C
C1
H
G
• Place the hob in the cut out. Mark the location of
the hob on the cooktop.
Worktop
Hob
Marker
• Remove the hob. Place the gasket on the line you
marked. Make sure that the line centres the gasket.
Ensure that the junctions overlap at the corners and
no gap is left along the sealing material.
Line you
marked
Gasket
• Insert the appliance into the aperture and fix in
position using the brackets (A) and screws (B). Adjust
the position of the brackets depending on the
thickness of the worktop and tighten the screws
evenly. Carefully trim away any excess sealing
material (C) from around the appliance.
A
C
B
t
t>20
mm
Gas Connection
Assembly of gas supply and leakage check
Connect the appliance in accordance with applicable
local and international standards and regulations. First,
check what type of gas is installed on the cooker.
This information is available on a sticker on the back
of the cooker. You can find the information related to
appropriate gas types and appropriate gas injectors in
the technical data table. Check that the feeding gas
pressure matches the values on the technical data
table, to be able to get the most efficient use and to
ensure the minimum gas consumption. If the pressure
of used gas is different than the values stated or is not
stable in your area, it may be necessary to assemble an

Installing your gas hob
Bringing it all together
Installing your gas hob 19
or online at www.bush-support.com If you still require further assistance, call one of our experts on 345 257 7271.
available pressure regulator on the gas inlet. You should
contact an authorised service centre to make these
adjustments.
Points that must be checked during flexible hose
assembly:
• If the gas connection is made by a flexible hose
fixed onto the gas inlet of the hob, it must be fixed
on by a pipe collar.
• Connect your appliance with a short and durable
hose that is as close as possible to the gas source.
• The permitted maximum length of the hose is 1.5
m.
• The device should be connected in line with the
relevant local gas standards.
• The hose must be kept clear of areas that may heat
up to temperatures of more than 90°C.
• The hose must not be cracked, torn, bent or folded.
• Keep the hose clear of sharp corners and objects
that could move.
• Before you assemble the connection, you must
make sure the hose is not damaged. Use bubbly
water or leakage fluids to perform the check. Do
not use a naked flame to check for gas leakage.
• All metal items that are used during gas connection
must be free from rust. Check the expiry date of any
components used for connection.
Points that must be checked during fixed gas
connection assembly:
The method used to assemble a fixed gas connection
(gas connection made by threads, e.g. a nut) varies
according to the country you are in. The most
common parts for your country will be supplied
with your appliance. Any other parts required can be
supplied as spare parts.
During connection, always keep the nut on the gas
manifold fixed while rotating the counter-part. Use
appropriately-sized spanners for a safe connection. For
surfaces between different components always use the
seals provided in the gas conversion kit.
The seals used during connection should also be
approved to be used in gas connections. Do not use
plumbing seals for gas connections.
Remember that this appliance is ready to be connected
to the gas supply in the country for which it has been
produced. The main country of destination is marked
on the rear cover of the appliance. If you need to use it
in another country, any of the connections in the figure
below may be required. In such a case, contact local
authorities to learn the correct gas connection.
Gas pipe
Gas pipe Gas pipe
Seal
Seal Seal
Hose
fitting
Hose
fitting
Hose
fitting
Hose
fitting
Gas hose
with collar
Gas hose
with collar
Mechanical
gas hose
Mechanical
gas hose
Gas pipe
Seal
Hose
fitting
Hose
fitting
Gas pipe
Hose
fitting
Mechanical
gas hose
The Cooker must be installed and maintained by
a suitably qualified gas registered technician in
accordance with current safety legislation.
WARNING:Do not use a naked flame to check
for gas leaks.
Gas Conversion (If available)
Your appliance is designed to be operated with LPG/
NG gas. The gas burners can be adapted to different
types of gas, by replacing the corresponding injectors
and adjusting the minimum flame length suitable to the
gas in use. For this purpose, the following steps should
be performed.
Changing injectors
Hob burners
• Cut off the main gas supply and unplug the
appliance from the mains electrical supply.

Installing your gas hob
Bringing it all together
Installing your gas hob
20
If you require any technical guidance or find that your product is not operating as intended, a simple solution can often be found in the Troubleshooting section of these instructions,
• Remove the burner caps and the adapters.
• Use a 7 mm spanner to unscrew the injectors.
• Replace the injector with the ones from the gas
conversion kit, with the correct diameters for the
type of gas that is going to be used, according to the
gas injector table.
Adapter
Spanner
Injector
Cup
Burner
cap
Adjusting the reduced flame position
First of all, make sure that the appliance is unplugged
from the the mains electrical supply and that the gas
feed is open. The minimum flame position is adjusted
with a flat screw located on the valve. For valves with
a flame failure safety device, the screw is located on
the side of the valve spindle as shown in the figures.
For valves without a flame failure safety device, the
screw is located inside the valve spindle as shown in
the figure. To make adjusting the flame position easier,
we recommend that you remove the control panel
(and the micro switch if your model has one) during the
alteration.
To determine the minimum position, ignite the burners
and leave them on in the minimum position. With the
help of a small screwdriver, fasten or loosen the bypass
screw by around 90 degrees. When the flame has a
length of at least 4mm, the gas is well distributed. Make
sure that the flame does not die out when passing from
the maximum position to the minimum position. Create
an artificial wind with your hand towards the flame to
see if the flames are stable.
The bypass screw must be loosened for conversion
from LPG to NG. For conversion from NG to LPG, the
bypass screw must be tightened. Make sure that the
appliance is unplugged from the mains electrical supply
and that the gas feed is open.
Valve with
flame failure
device
Bypass screw
Valve with flame failure
device Bypass
screw
Valve without flame failure
device
Bypass screw
(Inside the
hole)
Changing the gas inlet
For some countries, the gas inlet type can be different
for NG/LPG gases. In this case, remove the current
connection components and nuts (if any) and connect
the new gas supply accordingly. In all conditions,
all components used in gas connections should be
approved by local and/or international authorities. In all
gas connections, refer to the “Assembly of gas supply
and leakage check” clause explained above.
Electrical Connection and Safety (If
available)
WARNING: The electrical connection of this
appliance should be carried out by an authorised
service person or qualified electrician, according to the
instructions in this guide and in compliance with the
current local regulations.
WARNING: THE APPLIANCE MUST BE
EARTHED.
• Before connecting the appliance to the power
supply, the voltage rating of the appliance (stamped
on the appliance identification plate) must be
checked for correspondence to the available mains
supply voltage, and the mains electric wiring should
be capable of handling the appliance’s power rating
(also indicated on the identification plate).