Butts of Bawtry SP80WB User manual

1
36KG / 80LB WALK BEHIND SPREADER
SP80WB
INSTRUCTION MANUAL

2
SAVE THESE INSTRUCTIONS AND PRECAUTIONS. READ ALL PRECAUTONS AND
INSTRUCTIONS BEFORE USE.
2. Remove and identify loose parts from carton and bag.
1. HELPFUL HINTS: READ THE INSTRUCTIONS BEFORE ASSEMBLY
If your spreader does not spread evenly, be sure the FRONT on the gear box points to the
front of the spreader. The impeller must turn clockwise. Reversing the gear box will cause
the impeller to turn counter clockwise. Clean the impeller plate after each use. Fertilizer
stuck on the impeller blades will cause uneven spreading.
Your spreader is designed to be pushed at three miles per hour, which is a brisk walking
speed. Slower or faster speeds will change the spread patterns. Wet fertilizer will also
change the spread pattern and flow rate. Clean your spreader thoroughly after each use.
Wash between the shut off plate and bottom of the hopper.
Gears are permanently lubricated at the factory. Do not open the gear box or dirt may
enter.

3
STEP 1: Install impeller onto the Gear Box & Axle Assembly. Insert Screw M4x20 through
impeller then through Gear Box Axle.

4
STEP 2: Attach the Wheel Assembly Frame on each side of the Gear Box Axle and Fixing
Connecting Rod, insert two bolts M6x40 into the Fixing Connecting Rod through Wheel
Assembly Frame. Make sure the hole on Axle of Gear Box is on the right side when assembly as
shown. Attach Wheel Assembly Frames and Support Leg onto Hopper using bolts M6x70, lock

5
nuts M6 and Big Flat Washers Ø6. Note: The bolts and nuts needn't be tightened yet.
STEP 3: Insert Inner Axle Bushing into OuterAxle Bushing and make sure they are tight neatly.
Install right Wheel Assembly to right Axle using bolt M5x45 and lock nut M5, and then install the
Cap onto right Axle using a wooden or rubber hammer. Now install left Wheel Assembly to left
Axle, put a flat washer Ø16 and install the Cap onto leftAxle using a wooden or rubber hammer.

6
STEP 4: Insert Upper Handle into the Support Leg and tighten using bolts M6x40 and Lock
Nuts M6. NOW GO BACK AND TIGHTEN ALL NUTS AND BOLTS STARTING WITH FIRST
STEP. DO NOT OVER TIGHTEN.

7
STEP 5: (1) Insert the Steel Wire head of control cable into the small hole on Gauge and Lever
Assembly. (2)Release two bolts M5x10 and lock nuts on Press Plate. (3) Put the Plastic Tube
into the slot of Press Plate. (4) Tighten two bolts M5x10 and lock nuts again. (5). Insert R Pin.

8
STEP 6: ADJUSTMENTS. When you have finished all above steps, and if you find the
holes at the bottom of hopper can close and open completely by using the handle. You
don't need to do the following steps. If it does not close and open completely, you may

9
need to do the following steps. (1) Release two bolts M5x10 on clamp as shown. (2). Push the
handle to the top position, use your hand to adjust the adjustable plate so as to make sure the
hole at the bottom of hopper can be closed completely. (3). Push the handle to the lowest
position, use your hand to adjust the adjustable plate so as to make sure the hole at the bottom
of hopper can be opened completely. (4). And then tighten the bolts and nuts on clamp again.
To operate this spreader, push the handle to the lowest position (downwards). You may
move the position of Wing nut on the Gauge & Lever to adjust the space on the hole
between the hopper and the adjustable plate as per your need when spreading.
PARTS DRAWING

10

11
PARTS LIST
Ref# Description Qty Ref# Description Qty
1 Carriage Bolt M6x25 1 26 Support Leg 1
2 External-tooth Washer Ø8 1 27 Wheel Assembly Frame(Right) 1
3 Gauge and Lever Assembly 1 28 Thin Washer 1
4 Adjust Handle Pole 1 29 Pneumatic Wheel 2
5 Adjust Handle A 1 30 Flat Washer Ø16 1
6 Adjust Handle B 1 31 Axle End Cover 2
7 Screw M4x18 1 32 Inner Axle Bushing 2
8 Handle Grip 1 33 Outer Axle Bushing 2
9 Spacer 1 34 Gear Box & Axle Assembly 1
10 Wing Nut 1 35 Screw M4x20 1
11 Hopper 1 36 Hex Bolt M5x45 1
12 R Pin Ø2x60 1 37 Line Clamp Press Plate 2
13 Center Cover 1 38 Control Rod 1
14 Hex Bolt M6x70 4 39 Screw M5x10 2
15 Rivet Ø5X12 4 40 Nylon Washer 1
16 Active Adjustable Plate 1 41 Big Flat Washer Ø6 5
17 Fixed Adjustable Plate 1 42 Handle 1
18 Wheel Assembly Frame(Left) 1 43 Fixing Connection Rod 1
19 Impeller 1 44 Big End Cap 1
20 Hex Bolt M6x35 3 45 Small End Cap 2
21 Lock Nut M5 5 46 Lock Washer Ø6 1
22 Line Clamp Bottom Plate 1 47 Hopper Screen 1
23 Tube End Cap 4 48 Screw M5x12 2
24 Hex Bolt M6x40 6 49 Rain Cover 1
25 Lock Nut M6 12