BXB Electronics HDS-720 User manual

HDS-720
Network AV Controller
BXB ELECTRONICS CO., LTD.
User Manual

Index
System..............................................
Network..............................
IO..............................
Update...............................
All Presets....................
Appendix
HDC-713 Camera Setting.......
Contact us.......................................
１２
１３
１４
１５
１６
Safety Instructions...............................................
Rear Panel...........................................................
System Diagram..................................................
Image Display....................................................
Remote Control
Log In....................................................
Equipments..................................................
EquipmentsˍCamera..................
EquipmentsˍFCS.....................
Setting of Image Tracking..........................１０
１
２
４
５
６
８
９
１７
１８

Safety Instructions
１
1. Please read the instruction manual carefully before installing and using the apparatus.
2. Please save the instruction manual well for reference.
3. Please follow the instructions and aware of warning indications.
4. Except your dealer, please do not use any spare parts recommended by others.
5. Please use the fixing accessories provided by BXB. If the system is broken due to the improper fixing, BXB would not bear
the responsibility for compensation.
6. Please make sure the power cord has been fixed properly.
7. Do not use any three-hole plugs or extension cords as this would result in fire or short circuit.
8. Do not stuff anything into the apparatus or splash any liquid on it.
9. P l e a s e c o n t a c t m a i n t e n a n c e t e c h n i c i a n s if t h e c o n d i t i o n s below o c c u r :
A . P o w e r c o r d or p l u g is d a m a g e d .
B . Liquid has been s p i l l e d i n t o t h e a p p a r a t u s .
C. The system cannot operate normally even everything has followed the instructions.
D . T h e a p p a r a t u s f a l l d o w n or t h e c o v e r is d a m a g e d .
E. Other problems that need to be repaired.
10. To reduce the risk of damage caused by lightning strike, it is essential that all cables must be bonded well to the same
grounding point.
11. Install the apparatus and its other equipment carefully. Impacting and fierce shaking should be avoided.
12. Do n o t d i s a s s e m b l e or r e m o d e l t h e t h e a p p a r a t u s :
A. High voltage and sensitive electrical circuit are inside of the apparatus. Do not disassemble it to prevent electric shock.
B. The specification of any replaced spare part should be validated by manufacturer, or it may cause fire and short circuit.
1. Do not use the apparatus in the environment with improper temperature, moisture, and power level: the adequate range
is 0°C ~ 40°C (32°F ~ 104°F) and 90%below of moisture.
1. Do not expose the apparatus to rain and moisture. Put it in a dry location to avoid any damage of the inside components.
2. Do not clean the apparatus and its accessories with chemical detergent. Use a cloth dampened a little bit water instead.
3. Do not switch on/off the power of apparatus rapidly no matter it’s operating or off. It can maintain the regular operation of the
sensitive electronic circuit.
Caution: Please aware of the voltage accordance with that in your country.
Warning: Only qualified maintenance technicians can disassemble the cover of apparatus.

Rear Panel
Power supply: connect with AC100-230V to DC-5V adapter.
Power status indicator: turn on when the power status is normal; turn off when there’s the abnormal condition of power supply.
Trigger contact IN: the preserved contact.
RS-232 port: for connecting with BXB’s conference MCU
RS-485 port: for connecting with HDK-700 Compact Camera Controller (TX+ & TX-) to control PTZ cameras.
Audio port: perserved for extended functions.
USB port: perserved for extended functions.
Internet port: for connecting with BXB’s conference equipment or PC to operate graphical software and set the system configurations.
HDMI OUT: connect with monitors for displaying the image-tracking scene.
3
1
2
4
5
6
7
8
9
２
1 2 3 4 5 6 7 8 9

System Diagram
３

Connecting HDS-720 to the monitor’s HDMI input with HDMI cable, and switching the
monitor to HDMI channel.
HDS-720 Network AV
controller can do the video
tracking after connecting
conference system or camera
with internet or control cable.
HDS-720 Network AV
controller machine required
HDMI signal output to the
monitor with HDMI input. It
will show the camera’s image.
Image Display
４

1
Open internet browser.
2
Enter the IP address to the adress.
3
Choose the language in the login page,
English ,Chinese(Traditional), Korean are
available.
4
Logging with account/password.
Remote Control_Log in
http://192.168.168.120
５
The network setting of HDS-
720 can be DHCP or Static IP.
To confirm the IP address,
using HDMI output to check
current IP address.
Logging into the webcontrol
with the browser in the device.
For example: Chrome、
Microsoft Edge or Firefox, etc.
Entering the IP of HDS-720 to
the address to connect to the
web-control surface.
After log in to the control
website, log in with the
account and password. The
preset account is “admin”,
preset password is “00000”.
Changing password

Log in first time need to set the equipment first.
First time log into HDS-720’s
web control, system ask the
user to set the conference
system and camera first.
Click “Setting now”to go
“Equipments”to set up the
camera and conference unit.
Remote control_Log in first time
６

Equipments
７

1
Click “SCAN”to check the online IP
camera.
2
Click ” “ to preveiw each camera’s
image.
3
Click” “ to close the preview window.
4
Setting each camera’s ID and Name,
also check the status of the camera.
To set the IP camera of HDS-
720, use “SCAN”to check the
online IP camera. Also set up
the ID and the name of the
camera for further use.
“Status”can check the IP
camera communication status.
“Online”means the IP camera
working normally, you can
control and receive the image
from camera. “Offline”means
HDS-720 can’t receive the
signal from IP camera, unable
to control and preview the
camera.
Equipments_Camera
８