BYD Battery-Box HV User manual

BYD Battery-Box HV
QUICK REFERENCE GUIDE
Valid for Battery-Box H 5.1/6.4/7.7/9.0/10.2/11.5 (AU)
V 3

Overall structure
Tools
Skilled personnel recognized
This manual and the tasks and procedures described herein are intended for use by skilled workers only.
A skilled worker is defined as a trained and qualified electrician or installer who has all of the following skills and expenence:
• Knowledge of the functional principles and operation of on-grid systems.
• Knowledge of the dangers and risks associated with installing and using electrical devices and acceptable mitigation methods.
• Knowledge of the installation of electrical devices.
• Knowledge of and adherence to this manual and all safety precautions and best oractices.
Target Group
Installation environment requirements
Max.
+50℃
Min.
-10℃
Flammable material or
gas near the installation
Flammable wall
RH.
+5%~+95%
Packing list
Packing of BCU+BASE
①M6 2pcs ⑧White sealing plug×2pcs
⑦M6×2pcs⑤ Black sealing plug×3pcs ⑥White sealing plug ×2pcs
③ Expansion bolt M6 3pcs
* If connected to the SMA inverter, n = 5-8 Modules
Unless SMA & BYD updates the information.
Direct sunlight Direct rain fall Snow
accumulation
YES YES
NO NO
YES
NO
NO
NO
② M4 3pcs ④OT terminal for Ground×1pcs
Precision screwdriver
Packing of B-Plus H 1.28A
• In order to ensure the normal operation of Battery-Box, please be sure to update the firmware to the latest version and finish the
configuration on Battery-Box webpage in accordance with this document.
• The system switch must be off before installing.
• Please make sure the system switch is off in case of the system not working, and it would be better to repair it again within one
week, avoiding overdischarge or other problems happen.
• Please do not stack up batteries without protective package when storing or handling batteries, unless in the case of installation.
• Please note that this is the quick reference guide only. It is a shortened assistance for the installation of the Battery HV and
does not replace the original installation manual.The original installation manual must be read and understood completely
before installation. Please download and view the installation manual on this website: www.eft-systems.de (Downloads)
n=7, 9.0KWh
n=8, 10.2KWh
n=9, 11.5KWh
Wire clamp Phillips screwdriver Inclinometer Wrench churn drill
n=5, 6.4KWh
n=6, 7.7KWh
BCU
B-Plus H 1.28A
Base
n=4, 5.1KWh
* Whether the inverter supports 4 battery matching, please
consult the inverter manufacturer.

Open the BCU cover Over view of BCULocking
Unpack Balance
I nstall Wall-mount
Separate base
and BCU
Connect the cables Install the cover
8.
*
9.
6. 7.
4.
5.
2.
3.1.
Internet
P-P+
BCU + Base
B-Plus H 1.28A
13.
Inverter
P+
WAN
P-
JP2
JP1
Switch BCU PCBA COM1/2 P+/ P-
≥40cm ≥40cm
D=0-6.3cm
D
COM/WAN
P+ / P-/
COM
WAN
P+
P-
Ground
P+
P-
Install sealing plug
after install the screws
1. Lock diagonal screws.
2. Lock other screws.
1. Connecting Ground cable.
2. Connecting negative cable.
3. Connecting positive cable.
4. Connecting communication cable.
5. Connecting network cable.
≥40cm
Avoid the collision between
connector and corners.
Vertical install to protect the
connector
Before installing BCU, make sure
the system switch is switch off.

10a.
11.
12.
10b.
192.168.5.1.
192.168.5.1.
WLAN
BYDxxx
network 1
network 2
BYDxxx
123456789
cancel login
BYDxxx
Username installer
cancel login
Password byd@12345
192.168.6.1.
192.168.6.1
192.168.5.1.
192.168.5.1
BYDxxx
Username installer
cancel login
Password byd@12345
Please input file:
Upload
ON
ON
Update
Please input the file : Upload
If there is any new version on the server, clicking UpdateCheck will update the syesem.
WLAN password
Download the firmware : http://alpspower.com.au/download/
Connect through WIFI
Connect through ethernet cable
Setup system information
Update the firmware
You must update the lastest firmware of BCU after completing the Battery-Box H 5.1-11.4,to prevent battery overdischarge or damage.
network cable
①Connect the network cable
②Set your computer IP into a static IP
IP address:192.168.6.10
Subnet mask:255.255.255.0
Setting method reference computer system setting method
③
④
Battery-Box HV
Privacy Policy
Home
Device Information
Installation Config
Statistics Information
Current Alarm
History Alarm
Run Date
Set Password
Update
1 32
STEP 1 STEP 2 FINISH & REBOOT
1 32
STEP 1 STEP 2 FINISH & REBOOT
Time and Date *Hour : Min : Day : Month : Year :
Next
Installation
Battery-Box HV
Privacy Policy
Home
Device Information
Installation Config
Statistics Information
Current Alarm
History Alarm
Run Date
Set Password
Installtion
Server IP Address *
Series Battery Conts *
Inverter *
Country *
Asterisk(*)Indicates required fields
bboxhserver.byd.com.cn
4/5/6/7/8/9
SMA
1 32
STEP 1 STEP 2 FINISH & REBOOT
Last Next
Update
Search...
Search
These parameters is important.
Please make sure the correct configuration for these parameters,
otherwise the system might not work normally.
Reboot System…
Please wait about 50 seconds.

13a.
2
4
6
8
10
1
3
5
7
9D E F
A B C
2
4
6
8
10
1
3
5
7
9
13b.
SMA Sunny Boy Storage 2.5 software version ≥ SBS2.5-V2.04.23
SMA Sunny Boy storage 2.5 / 3.7 / 5.0 / 6.0
SMA
Sunny Boy
Storage
Battery-Box
No. SMA SBS Parameter
1Battery-Areas of application-Lower Imt deep disch.Protect area prior shutdown
Battery-Nutzungsbereiche-Untere Grenze des Tiefenladenschutzbereichs vor Abschaltung 2%
2Battery-Areas of application-Minimum width of deep discharge protection area
Battery-Nutzungsbereiche-Minimale Breite des Tiefenladenschutzbereichs 3%
3Battery-Areas of application-Area width for conserving battery sate of charge
Battery-Nutzungsbereiche-Breite des Bereichs zur Erhaltung des Batterieladezustands 3%
4Battery-Areas of application-Minimum width of own consumption area
Battery-Nutzungsbereiche-Minimale Breite des Tiefenladenschutzbereichs 100%
KOSTAL PIKO
BA
pin pin
2
4
6
8
10
1
3
5
7
9
1
3
3
4
5
7
5
6
2
4
1
3
6
10
9
8
5
712 3 4 5 6
RS485 - EM-Typ 4 KOSTAL
Battery-Box
Battery-Box
Battery-Box
KOSTAL PIKO BA software version ≥ Firmware:FW-B2.30
UI:UI-B6.44
KOSTAL PIKO BA
Valid for PIKO 6.0 BA，PIKO 8.0 BA，PIKO 10 BA
Choose any one
KOSTAL
PLENTICORE
PLUS
2
4
1
3
6
10
9
8
5
7
B-Box
pin
KPP
pin
1
3
5
7
1
6
5
4
1 2 3 4 5 6
KOSTAL PLENTICORE plus
Set Battery parameters in the SMA inverter:
Use a twisted-pair wire for CAN_H and CAN_L (PIN 6 and 8). This is important for the stability of the CAN communication.
Choose any one
pin pin
2-EN 11V+
4-EN 11V-
6-CAN H
8-CAN L
B-Enable
C-GND and
shielding
E-CAN H
D-CAN L
Battery-Box SMA SBS

13c.
Fronius Symo Hybrid
Fronius Symo Hybrid
Fronius Symo Hybrid
2
4
6
8
10
1
3
5
7
9
Choose any one
2
4
1
3
6
10
9
8
5
7
Battery-Box
Pin
Fronius
pin
2
4
5
7
+
-
D+
D-
2
4
1
3
6
10
9
8
5
7
2
1
3
6
10
9
8
JP2
Remove JP2
Fronius
Smart Meter
Fronius
Smart Meter
Fronius Smart Meter
Fronius Smart Meter
Battery-Box
Battery-Box
D+ D- -
D- -
5
7
4
Please refer to the inverter installation manual for detailed wiring.
D+
JP2 is in the BCU of Battery-Box
Connection method 1
Connection method 2
1.When connecting the meter in the second connection mode, the jumper
cap above the JP2 in the BCU PCBA must be unplugged.
If not unplugged, it is possible that the Battery-Box and inverter will not be
able to communicate properly.
2.Due to simplicity of installation, connection method 1 is recommended.

BMS
13d.
Goodwe ET Inverter
Goodwe ET
① 1 Cut the BMS cable of the Goodwe ET (according to Goodwe Manual).
③ Download the EzViewer for setting the inverter ④ Setting the inverter
IOS APP Store
ANDROD
2
4
1
3
6
10
9
8
5
7
2
4
1
3
6
10
9
8
5
7
Blue
white-blue
Goodwe
BMS② Connect the blue PIN to terminal block position 6 and the white-blue PIN to
terminal block position 8, according to the picture.
Choose any one
2
4
1
3
6
10
9
8
5
7
Blue
white-blue
Battery-Box
Pin
Ingeteam
pin
6
8
CAN IN-H
CAN IN-L
J76
Battery-Box
Ingeteam
Ingeteam Ingecon Sun Storage 3TL and 6TL
13e.
Ethernet cable without the RJ45 terminals

14.
Battery-Box HIGH VOLTAGE EXTENSION
Charge or discharge the original battery module so
that its SOC becomes 30% to 40%, and add another
battery module. The actual SOC difference will be
automatically balanced in the next 2 weeks or so.
(Batterry-Box capacity may not be enough during this
time, this is normal)
15b.
SOC=100%
100% = Green LED
constantly on
HV Charger
15a.
HV Charger
Charging = Green
LED blinking
With charger
15c.
SOC=100%
SOC=100%
This manual is a shortened assistance for the installation of the Battery-Box HV and does not replace the original manual, which can be found on
http://alpspower.com.au.The installation must be carried out by a qualied expert. Attention, High Voltage Storage! Improper handling can cause
danger and damage.
15d.
n=3-8 Modules
m=1-6 new Modules
Up to a maximum of 9
Battery-Box HV
Privacy Policy
Home
Device Information
Installation Config
Statistics Information
Current Alarm
History Alarm
Run Date
Set Password
Update
Installation
1 32
STEP 1 STEP 2 FINISH & REBOOT
1 32
STEP 1 STEP 2 FINISH & REBOOT
Time and Date *Hour : Min : Day : Month : Year :
Next
Server IP Address *
Series Battery Conts *
Inverter *
Country *
Asterisk(*)Indicates required fields
bboxhserver.byd.com.cn
SMA
Last Next
1 32
STEP 1 STEP 2 FINISH & REBOOT
Reboot System…
Please wait about 50 seconds.
n+m
15c.
SOC=30%-40%
SOC=30%-40%
Without charger
New battery module
Original battery
system
These parameters is important.
Please make sure the correct configuration for these parameters,
otherwise the system might not work normally.