BYMUSE FLO User manual

USER GUIDE
BYMUSE FLO Wireless Neckband Earphones

1
BYMUSE FLO earphones Quick Start Guide
In the Package
USER GUIDE
BYMUSE FLO Wireless Neckband Earphones
3 - pairs of in-ear earphones
Large | Med | Small
3 - pairs iso-Fit Cushions
Large | Med | Small
1 - USB Micro
Charging Cable
(Med size installed on the headphones.)
(Med size installed on the headphones.)

2
Note: When you wear the BYMUSE FLO headset, note that the
side with the control button is to the right.
Getting to know your BYMUSE FLO
In-ear earphones
Iso-Fit Cushion
LED Indicator
Light
Left Right
Mic
Rubber Flap
Covers Micro USB
Charging Port
Backsideof
InlineControls

3
charge a low battery
Charging the Battery
Step 2: Insert the smaller end of
the Micro USB Cableinto the Micro
USB Charging Port as shown.
Step 3: Insert the other end of the
Micro USB cableinto either a USB
wall charger for a smartphoneor
a USB port on your laptop to
charge the battery.
The LED
Indicator Lightwill come on.
Step 1: Carefully lift the rubber
flap that covers the Micro USB
Charging Port and rotate the
flap to the rear
Slowly flashing Red when charging
Solid Red when fully charged
The LED Indicator Light
Your BYMUSE FLO rechargeable
battery will have a partial charge and
be ready to play. For maximum
playtime, fully charge the battery.
Music Play Time
Up to 8 hours on afull charge, with
volume at 60%. Louder volume will
reduce play time.
Low Charge Remaining Indicator
When the battery charge gets down
to 20% there will be a voice prompt
and the RED LED Light will flash in
rapid succession.
Automatic Turn Off
The BYMUSE FLO will turn off 15
minutes after being disconnected
from your mobiledevice.
Charge indicator on iPhone
Charging Time
It will take about2 to 3 hours to fully
charge a low battery
The vertical battery charge level
will appear in the top right
corner of youriPhone screen

4
LED Indicator Light
will turn on
Flashing Blue rapidly
indicates BYMUSE FLO isin pairing mode
Flashing Blue 3 timesevery 5 seconds
indicates
BYMUSE FLO is connected to a
mobiledevice and is ready to play
Turning On and Off
Press and Hold Down button for2 Seconds
Turn ON
LED Indicator Light
flashes RED twice and turns off
LED Indicator Light
Press and Hold Down button for2 Seconds
Turn OFF

5
Pairing&Connecting to your mobile device
Turn ON your BYMUSE FLO
- Your mobile device needs to be within 30 unobstructed feet of the BYMUSE FLO
- Make sure your BYMUSE FLO battery has a sufficient charge
The LED Indicator Light will turn on
If the blue light is rapidly flashing
the BYMUSE FLO is ready to pair and connect.
If the blue light is flashing 3 timesevery 5 seconds
the BYMUSE FLO has automatically reconnected to the last
mobiledevice itwas connected to and is ready to play.
The BYMUSE FLO will try to reconnect each time it is turned on.
The BYMUSE FLO can be connected to one mobile device at
a time. To pair and connect to adifferent mobiledevice, you
need to disconnect the currently paired mobiledevice.
To disconnect it:
press and hold down the button and the button
together for 3 seconds.
The blue light will begin flashing and the BYMUSE FLO is ready
to pair and connect.

6
- Go to Settings> Bluetooth, check Bluetooth is on
- Select ‘ BYMUSE FLO ’ when it appears under OTHER DEVICES
- The BYMUSE RUN will connect in a few seconds
- The LED Light on your BYMUSE FLO will flash BLUE 3 times every
5 seconds and you are ready to play
- Go to Settings > Bluetooth, check Bluetooth is on
- Scan or Search and select ‘ BYMUSE FLO ’when it appears under
AVAILABLE DEVICES
- The BYMUSE FLO will connect in a few seconds
- The LED Light on your BYMUSE FLO will flash BLUE 3 times every
5 seconds and you are ready to play
Note: Your Smartphone or Tablet instructions may vary, please check
your mobile device’s manual for specific pairing instructions.
Pairing&Connecting to your
MobileDevice (continued)
To pair and connect from an iPhone, iPad, or iPod:
To pair and connect from a Smartphone or Tablet:

7
Play Controls
Press
Press
Press and Hold for 2 Seconds
Press and Hold for 2 Seconds
Volume Up
Press
Volume Down
Next Track
Play / Pause
Previous Track

8
To Hear the Best Sound and Best Bass
from your BYMUSE FLO Select the
Best Fitting In-Ear FLO
Side View
Top View
LARGEMED SMALL
A comfortable snug fitof the In-Ear FLO provides the highest quality
listening experience with the BYMUSE FLO .We suggest starting with the
medium sizeIn-Ear FLO to learn if they are snug and comfortable. If
they donot feel snug try the large In-Ear FLO , and if the medium are too
tight try the small In-Ear FLO .The largest sizeIn-Ear FLO that are
comfortablewill provide the best overall sound experience.

9
Comfort Fit with Iso-Fit Cushions
Sideview
Sideview
Lineup holes
Iso-Fit Cushion
In-Ear FLO
Step 1: With the In-Ear FLO
removed, slide the Iso-Fit
Cushion over the shaft of
the earbud with the smaller
tube opening facing
outwards from the earbud
and the small holes lined up
Step 2: Slide the In-Ear FLO
onto the earbud shaft
Step 3: Your BYMUSE FLO
are now ready to insert
into your ear
The Iso-Fit Cushions help provide a comfortable snug fit,
perfect for listening during sports and physical activity.

10
Right
Iso-Fit Cushion
Right Earbud
Install the Right(R) Iso-Fit Cushion onto the Right(R)
earbud,with the holes lined up as shown.Insert the Right
earbud into your right ear canal. The Iso-Fit Cushion
should fit comfortably and snugly in your ear, allowing for
the best sound quality.
Wearing your BYMUSE FLO Under-Ear
Lineup holes

11
PhoneCall Controls
Reject Call or
Transfer Call Between
BYMUSE FLO & Smartphone
Answer
Incoming Call
or End Call
Last Number Redial
Press
Press and Hold for 2 Seconds
Press Twice
Call Mute
Press and Hold for 2 Seconds

12
Troubleshooting
BYMUSE FLO will not turn on
• The battery may have become fully drained. Charge the BYMUSE FLO using a USB
wall charger from a Smartphone/iPhoneor tablet for at least 15 minutes, then press
the button to turn the BYMUSE FLO on. Then continue charging the battery.
Cannot pair or connect the BYMUSE FLO with my mobile device
• Your mobiledevice may beout of range(signal loss) and you will hear a doublebeep
every 15 seconds. Moveback within 30 unobstructed feet of the mobiledevice. The
BYMUSE RUN will reconnect, there will be a voice prompt “ Dida ”. Click the O button
to start playing again.
• Check that your BYMUSE FLO has a sufficient battery charge, the headphones may
not connect when the battery has a low charge. Connect the BYMUSE FLO to a
charging source and try again to pair and connect.
• Check the LED light to make sure itis flashing Blue rapidly. If itis solid blue the
BYMUSE FLO is already connected to another mobiledevice. The BYMUSE FLO can
be connected to one mobiledevice at a time. You need to disconnect the connected
mobiledevice then you can connect to the next mobiledevice. Please see
instructions on page 5.
• Your mobiledevice may have a temporary Bluetooth connection issue please try the
following steps which can resolve this: (continued next page)

13
Cannot pair or connect the BYMUSE FLO with my mobile device (continued)
No audio from your mobile device
• Make sure the volume is up on your BYMUSE FLO.
• Remove the BYMUSE FLO from the Bluetooth device list on your mobile device,
restart your mobiledevice, and then re-pair and connect to the BYMUSE FLO.
• Make sure your mobiledevice isplaying audio,not paused and volume isup.
• Your mobiledevice may beout of range, move closer within 30 unobstructed feet.
• Turn your BYMUSE FLO off and back on.
• Some mobiledevice have a defaultvolume when they connect to a new device, try
turning up the volume on the BYMUSE FLO and the mobile device after connecting.
For iPhone, iPad, iPod
• Turn off the BYMUSE FLO , go to the Bluetooth device list on your iPhone, iPad or
iPod and check if the BYMUSE
FLO is listed. If it listed press the icon next to the
BYMUSE FLO and then forget this device, twice. With the BYMUSE FLO removed
from the list or if itwas notlisted, do ahard reset on youriPhone, iPad oriPod by
pressing and holding down the Home and sleep buttons at the same time for about
10 secondsuntil the Appleicon appears and it restarts. When it restarts turn on the
BYMUSE
FLO and then try again to pair and connect.
For Smartphones and Tablets
• Turn off the BYMUSE FLO , go to the Bluetooth device list on your Smartphone or
Tablet and check if the BYMUSE FLO is listed. If it listed press the icon next to the
BYMUSE FLO and then press Unpair this device. With the BYMUSE FLO unpaired or
if itwas not listed, do a hard restart on yourSmartphone or Tablet. When it restarts
turn on the BYMUSE FLO and then try again to pair and connect.

14
Poorsound quality from a mobile device
• Your mobiledevice may beoutof range, move closer within 30 unobstructed feet.
• If youriPhone, iPad, oriPod has an option to select stereo orMono, select Stereo.
• Try another track or music app.
• Turn your BYMUSE FLO off and back on.
• Some mobiledevices need to have their WiFi turned off to improve audioquality
over Bluetooth.
• It may be that you need to re-pair the BYMUSE FLO with your mobile device. Remove
it from yourpaired devices list, restart the mobiledevice and then follow the steps to
re-pair the headphones.
BYMUSE FLO won’t fit or stay in place
• Try one size larger In-Ear FLO.
• Make sure you have the Iso-Fit Cushions in place.
• Be sure the BYMUSE FLO is being worn correctly by checking on each earbud
forwhich sideit should beworn on.

15
FCC Warning
FCC ID: 2ATRS-BYMUSEFLO
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
(1) This device may not cause harmful interference, and (2) This device must accept
any interference received, including interference that may cause undesired
operation.
NOTE 1: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
NOTE 2: Any changes or modifications to this unit not expressly approved by the
party responsible for compliance could void the user's authority to operate the
equipment.

16
包装内容
BYMUSE FLO 耳机 快速操作指南
耳塞大中小号各1对
耳翼小号1对
Micro USB充电线1条
耳翼大号1对
耳翼中号1对
(中号耳翼已装在耳机上)
(中号耳塞已装在耳机上)
CH
USER GUIDE
BYMUSE FLO Wireless Neckband Earphones

17
关于BYMUSE FLO
注：您在佩戴BYMUSE FLO耳机时，注意有控制按键的一边为右边。
耳套
耳翼
左
麦克风
后面板 正面板的
控制按键
LED指示灯
右
Micro USB
硅胶塞
CH

18
您的 BYMUSE FLO 无线蓝牙耳机的电池
在出厂时只充了一部分电，
我们建议您先充满电后再播放，这
样可以让播放时间最长久。
音乐播放时间
电池充满电后、音量在60%情况下
播放时间可以达到8小时，加大音量
将会缩短播放时间。
低电量
当电量降低到15%，将会有一个低电
量“Dong”语音提示, 且红色的LED
灯会连续快闪。
自动关机
如果BYMUSE FLO的蓝牙连接断开15分钟
后耳机会自动关机来省电。
第二步:
轻轻地插入 Micro USB线
到耳机的Micro USB 接口
第三步:
轻轻地插入Micro USB线
的另外一头到带USB接
口的充电器或者电脑的
USB接口给耳机电池充电，
需要用二至三小时充满
电池
备注：在插入USB线给耳
机充电时，为了保护电池
寿命，此时在耳机上长按
键不能开机，需要拔出
USB线后,长按才能使
耳机开机。
在iPhone或iPad屏幕上会实时显示耳
耳机充电
第一步:
小心地打开
Micro USB 硅胶塞
LED指示灯
红色慢闪 – 表示电池正在充电
红色恒亮 – 表示电池已经充满
机的电量， 这垂直的电量指示将
会出现在您的
iPhone 或iPad屏幕
的右上角位置。
CH

19
蓝色LED灯
蓝色灯快速闪烁
表示正在配对中
蓝色灯慢速闪烁(每5秒3次)
表示已连接上了一个蓝牙设备
语音提示
“Duang”
语音提示
“Duang”
红色LED灯
红色灯闪烁两次
开/关机
开机 关机
长按此按键
1秒钟开机
长按此按键
2秒钟关机
CH