BYMUSE RUN User manual

USER GUIDE
BYMUSE RUN Wireless Sport Earphones

1
BYMUSE RUN earphones Quick Start Guide
In the Package
4 - pairs of in-ear earphones
Large | Med | Small | Mini
(Small size installed on the headphones.)
(Med size installed on the headphones.)
Large iso-Fit Cushions
1 - USB Micro
Charging Cable
USER GUIDE
BYMUSE RUN Wireless Sport Earphones

2
Note: When you wear the BYMUSE RUN headset, note that the
side with the control button is to the right.
In-ear earphones
Getting to know your BYMUSE RUN
Left
Iso-Fit Cushion
LED Indicator
Light
Right
Mic
Rubber Flap
Covers Micro USB
Charging Port
Backsideof
InlineControls

3
charge a low battery
Charging the Battery
Step 2: Insert the smaller end of
the Micro USB Cableinto the Micro
USB Charging Port as shown.
Step 3: Insert the other end of the
Micro USB cableinto either a USB
wall charger for a smartphoneor
a USB port on your laptop to
charge the battery.
The LED
Indicator Lightwill come on.
Step 1: Carefully lift the rubber
flap that covers the Micro USB
Charging Port and rotate the
flap to the rear
Slowly flashing Red when charging
Solid Red when fully charged
The LED Indicator Light
Your BYMUSE RUN rechargeable
battery will have a partial charge and
be ready to play. For maximum
playtime, fully charge the battery.
Music Play Time
Up to 8 hours on afull charge, with
volume at 60%. Louder volume will
reduce play time.
Low Charge Remaining Indicator
When the battery charge gets down
to 20% there will be a voice prompt
and the RED LED Light will flash in
rapid succession.
Automatic Turn Off
The BYMUSE RUN will turn off 15
minutes after being disconnected
from your mobiledevice.
Charge indicator on iPhone
Charging Time
It will take about2 to 3 hours to fully
charge a low battery
The vertical battery charge level
will appear in the top right
corner of youriPhone screen

4
LED Indicator Light
will turn on
Flashing Blue rapidly
indicates BYMUSE RUN isin pairing mode
Flashing Blue 3 timesevery 5 seconds
indicates
BYMUSE RUN is connected to a
mobiledevice and is ready to play
Turning On and Off
Press and Hold Down button for2 Seconds
Turn ON
LED Indicator Light
flashes RED twice and turns off
LED Indicator Light
Press and Hold Down button for2 Seconds
Turn OFF

5
Pairing&Connecting to your mobile device
Turn ON your BYMUSE RUN
- Your mobile device needs to be within 30 unobstructed feet of the BYMUSE RUN
- Make sure your BYMUSE RUN battery has a sufficient charge
The LED Indicator Light will turn on
If the blue light is rapidly flashing
the BYMUSE RUN is ready to pair and connect.
If the blue light is flashing 3 timesevery 5 seconds
the BYMUSE RUN has automatically reconnected to the last
mobiledevice itwas connected to and is ready to play.
The BYMUSE RUN will try to reconnect each time it is turned on.
The BYMUSE RUN can be connected to one mobile device at
a time. To pair and connect to adifferent mobiledevice, you
need to disconnect the currently paired mobiledevice.
To disconnect it:
press and hold down the button and the button
together for 3 seconds.
The blue light will begin flashing and the BYMUSE RUN is ready
to pair and connect.

6
- Go to Settings> Bluetooth, check Bluetooth is on
- Select ‘ Bymuse Run ’ when it appears under OTHER DEVICES
- The BYMUSE RUN will connect in a few seconds
- The LED Light on your BYMUSE RUN will flash BLUE 3 times every
5 seconds and you are ready to play
- Go to Settings > Bluetooth, check Bluetooth is on
- Scan or Search and select ‘ BYMUSE RUN ’when it appears under
AVAILABLE DEVICES
- The BYMUSE RUN will connect in a few seconds
- The LED Light on your BYMUSE RUN will flash BLUE 3 times every
5 seconds and you are ready to play
Note: Your Smartphone or Tablet instructions may vary, please check
your mobile device’s manual for specific pairing instructions
Pairing&Connecting to your
MobileDevice (continued)
To pair and connect from an iPhone, iPad, or iPod:
To pair and connect from a Smartphone or Tablet:

7
Play Controls
Press
Press
Press and Hold for 2 Seconds
Press and Hold for 2 Seconds
Volume Up
Press
Volume Down
Next Track
Play / Pause
Previous Track

8
To Hear the Best Sound and Best Bass
from your BYMUSE RUN Select the
Best Fitting In-Ear RUN
Side View
Top View
Large SmallMedium Mini
A comfortable snug fitof the In-Ear RUN provides the highest
quality listening experience with the BYMUSE RUN.We suggest
starting with the medium sizeIn-Ear RUN to learn if they are snug
and comfortable. If they donot feel snug try the large In-Ear RUN,
and if the medium are too tight try the small In-Ear RUN.The
largest sizeIn-Ear RUN that are comfortablewill provide the best
overall sound experience.

9
Comfort Fit with Iso-Fit Cushions
Sideview
Sideview
Lineup holes
Iso-Fit Cushion
In-Ear RUN
Step 1: With the In-Ear RUN
removed, slide the Iso-Fit
Cushion over the shaft of
the earbud with the smaller
tube opening facing
outwards from the earbud
and the small holes lined up
Step 2: Slide the In-Ear RUN
onto the earbud shaft
Step 3: Your BYMUSE RUN
are now ready to insert
into your ear
The Iso-Fit Cushions help provide a comfortable snug fit,
perfect for listening during sports and physical activity.

10
Right
Iso-Fit Cushion
Right Earbud
Install the Right(R) Iso-Fit Cushion onto the Right(R)
earbud,with the holes lined up as shown.Insert the Right
earbud into your right ear canal. The Iso-Fit Cushion
should fit comfortably and snugly in your ear, allowing for
the best sound quality.
Wearing your BYMUSE RUN Under-Ear
Lineup holes

11
Lay cablebehind ear, drape Left earbud
upsidedown, and insert Left earbud
into right ear canal
For an even more secure fitduring rigorous activity you
can wear your BYMUSE RUN Over-Ear, putting your Left
earbud in your right ear and your Right earbud in your
left ear. The inline controls will then be on yourleft side.
Wearing your BYMUSE RUN Over-Ear

12
PhoneCall Controls
Reject Call or
Transfer Call Between
BYMUSE RUN & Smartphone
Answer
Incoming Call
or End Call
Last Number Redial
Press
Press and Hold for 2 Seconds
Press Twice
Call Mute
Press and Hold for 2 Seconds

13
Troubleshooting
BYMUSE RUN will not turn on
• The battery may have become fully drained. Charge the BYMUSE RUN using a USB
wall charger from a Smartphone/iPhoneor tablet for at least 15 minutes, then press
the button to turn the BYMUSE RUN on. Then continue charging the battery.
Cannot pair or connect the BYMUSE RUN with my mobile device
• Your mobiledevice may beout of range(signal loss) and you will hear a doublebeep
every 15 seconds. Moveback within 30 unobstructed feet of the mobiledevice. The
BYMUSE RUN will reconnect, there will be a voice prompt “ Dida”. Click the O
to start playing again.
button
• Check that your BYMUSE RUN has a sufficient battery charge, the headphones may
not connect when the battery has a low charge. Connect the BYMUSE RUN to a
charging source and try again to pair and connect.
• Check the LED light to make sure itis flashing Blue rapidly. If itis solid blue the
BYMUSE RUN is already connected to another mobiledevice. The BYMUSE RUN can
be connected to one mobiledevice at a time. You need to disconnect the connected
mobiledevice then you can connect to the next mobiledevice. Please see
instructions on page 5.
• Your mobiledevice may have a temporary Bluetooth connection issue please try the
following steps which can resolve this: (continued next page)

14
Cannot pair or connect the BYMUSE RUN with my mobile device (continued)
No audio from your mobile device
• Make sure the volume is up on your BYMUSE RUN.
• Remove the “Bymuse Run “ from the Bluetooth device list on your mobile device,
restart your mobiledevice, and then re-pair and connect to the BYMUSE RUN .
• Make sure your mobiledevice isplaying audio,not paused and volume isup.
• Your mobiledevice may beout of range, move closer within 30 unobstructed feet.
• Turn your BYMUSE RUN off and back on.
• Some mobiledevice have a defaultvolume when they connect to a new device, try
turning up the volume on the BYMUSE RUN and the mobile device after connecting.
For iPhone, iPad, iPod
• Turn off the BYMUSE RUN, go to the Bluetooth device list on your iPhone, iPad or
iPod and check if the BYMUSE RUN is listed. If it listed press the icon next to the
BYMUSE RUN and then forget this device, twice. With the BYMUSE RUN removed
from the list or if itwas notlisted, do ahard reset on youriPhone, iPad oriPod by
pressing and holding down the Home and sleep buttons at the same time for about
10 secondsuntil the Appleicon appears and it restarts. When it restarts turn on the
BYMUSE RUN and then try again to pair and connect.
For Smartphones and Tablets
• Turn off the BYMUSE RUN, go to the Bluetooth device list on your Smartphone or
Tablet and check if the BYMUSE RUN is listed. If it listed press the icon next to the
BYMUSE RUN and then press Unpair this device. With the BYMUSE RUN unpaired or
if itwas not listed, doahard restart on yourSmartphone or Tablet. When it restarts
turn on the BYMUSE RUN and then try again to pair and connect.

15
Poorsound quality from a mobile device
• Your mobiledevice may beoutof range, move closer within 30 unobstructed feet.
• If youriPhone, iPad, oriPod has an option to select stereo orMono, select Stereo.
• Try another track or music app.
• Turn your BYMUSE RUN off and back on.
• Some mobiledevices need to have their WiFi turned off to improve audioquality
over Bluetooth.
• It may be that you need to re-pair the BYMUSE RUN with your mobile device. Remove
it from yourpaired devices list, restart the mobiledevice and then follow the steps to
re-pair the headphones.
BYMUSE RUN won’t fit or stay in place
• Try one size larger In-Ear RUN.
• Make sure you have the Iso-Fit Cushions in place.
• Be sure the BYMUSE RUN is being worn correctly by checking on each earbud
forwhich sideit should beworn on.

16
FCC ID: 2ATRS-BYMUSERUN
This device complies with Part 15 of the FCC Rules. Operaon is subject to the
following two condions:
(1) This device may not cause harmful interference, and (2) This device must accept
any interference received, including interference that may cause undesired
operaon.
NOTE 1: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protecon against harmful interference in a
residenal installaon. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instrucons,
may cause harmful interference to radio communicaons. However, there is no
guarantee that interference will not occur in a parcular installaon. If this
equipment does cause harmful interference to radio or television recepon, which
can be determined by turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separaon between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
NOTE 2: Any changes or modificaons to this unit not expressly approved by the
party responsible for compliance could void the user's authority to operate the
equipment.
FCC Warning

USER GUIDE
BYMUSE RUN Wireless Sport Earphones
(中号耳塞已装在耳机上)
(小号耳翼已装在耳机上)
17
BYMUSE RUN耳机 快速操作指南
包装内容
Micro USB充电线1条
耳塞大号1对 耳塞小号1对 耳塞mini号1对
耳翼大号1对
CH

18
注：您在佩戴 BYMUSE RUN 耳机时，注意有控制按键的一边为右边。
关于BYMUSE RUN
左
麦克风
后面板
LED指示灯
右
Micro USB
硅胶塞
正面板的
控制按键
耳套
耳翼
CH

19
耳机充电
您的BYMUSE RUN无线蓝牙耳机的电池
在出厂时只充了一部分电，
我们建议您先充满电后再播放，这样
可以让播放时间最长久。
音乐播放时间
电池充满电后、音量在60%情况下
播放时间可以达到8小时，加大音量
将会缩短播放时间。
低电量
当电量降低到20%，将会有一个“Dong”语
音提示, 且红色的LED灯会连续快闪。
自动关机
如果
BYMUSE RUN 的蓝牙连接断开15分钟后
耳机会自动关机来省电。
在iPhone或iPad屏幕上会实时显示耳机的电量
LED指示灯
红色慢闪 – 表示电池正在充电
红色恒亮 – 表示电池已经充满
这垂直的电量指示将会出现在您的
iPhone
或iPad屏幕的右上角位置。
第一步:
小心地打开
Micro USB 硅胶塞
第二步:
轻轻地插入 Micro USB线
到耳机的Micro USB 接口
第三步:
轻轻地插入Micro USB线
的另外一头到带USB接
口的充电器或者电脑的
USB接口给耳机电池充电，
需要用二至三小时充满
电池
备注：在插入USB线给耳
机充电时，为了保护电池
寿命，此时在耳机上长按
键不能开机，需要拔出
USB线后,长按才能使
耳机开机。
CH