Byron Home Easy HE-403 User manual

RE-INVENTING THE HOME
HOME
easy
HE-403 Remote control
Outdoor PIR
V1.0
Installation:
The HE-403 Outdoor PIR adds extra security and ease of
use to your Home Easy products
  -Selectable timer setting
  -10Metre Detection Range
  -IP44 Weather Proof
  -25 Metre Wire Free Range
  -Battery Powered 3*AAA
The HE-403 allows you to control your Home EasyReceiver sockets or modules
via a wire free remote control PIR sensor.When the PIR beam is broken the
outdoor PIR will switch on your Remote control sockets for between 15
seconds and
4 Minutes. Ideal for controlling out door lighting,staircase lighting and house
hold lighting for added security.
1. Fist select your required location, it's recommended that the PIR is installed
approximately 3 metres off the ground (ideally under the eaves of the building)
and, away from direct sources of sunlight or heat.
Warning: Avoid installing the Remote Control PIR onto metallic surfaces
and above heating vents as this will affect the operating performance.
2. Remove the PIR unit from the base and Using the mounting bracket as a
template mark and drill appropriate holes and fix the bracket securely using
the appropriate screws and wall plugs (included).
1. Unclip the battery cover from the bottom of the
PIR using a small screw driver.
Changing Batteries:
2. Remove the batteries and replace using 3
new 'AAA' batteries, making sure the polarity
is correct.
Always dispose of old batteries in an
environmentally responsible way
3. Replace the battery cover making sure the rubber seal is correctly
aligned and firmly push the case together.
Rubber seal
Avoid Direct Heat
Sources
Detection Distance

C H Byron
34, Sherwood Rd
Aston Fields
Bromsgrove
B60 3DR
Contact Details:
433MHz
R&TTE
APPROVED
CH Byron Electrical United Kingdom. www.chbyron.com
A
B
DK
FIN
F
D
GR
LT
IRL
I
L
NL
P
E
S
UK
BG
CZ
EST
H
IS
LV
M
N
SK
SLO
CH
PL
RO
0560
Tel: [phone]
Fax: [phone]
Web: www.chbyron.com
E-mail:
[email protected]
No Activation:  -Check the battery life and pairing with receiver socket or 

  module.
Receiver stays ON -The PIR might be receiving false signals due to the 
continuously: selected location, try adjusting the angle.
Radom Activation: -Wind/rain can cause the PIR unit to activate , try a new  
location if needed.
-Small animals can activate the PIR.
-Try selecting a new address code.
-Passing traffic or pedestrian can activate the PIR, alter 
  the detection angle.
Contact:   Helpline: 0845 2301 231
RF Range: The radio signals operating distance is reduced when the signal has
to pass through walls.The radio signals achieve a range of 25m;this can be
reduced depending on the type of material.
TIMBER CONCRETE
METAL GLASS
PLASTICS
10 - 15%
BRICK
10 - 40%
40- 80%
10 - 40%
90% 5 - 15%
Range
Reduction Guide:
Detection Area:
Help Section :
Product Specification:
Remote Control: HE-403
Battery: 3 * AAA
Range: 25Metres (Open Distance)
Frequency: 433.92MHz
IP44 Weather Proof
Warning: Never Exceed the Product Specification
Setting Timer :
The HomeEasy Outdoor PIR will active for a predefined period of time when
activated,this can be set between 15 seconds and 4 minutes.
To select the time period, remove the battery cover and using a small screw
driver rotate the dial to select the required time.
Timer Setting:
1min:
15 sec:4 min(max):
The PIR detection area is 110 degrees,this can be reduced using the clip-on
covers (included).if required the covers can be cut to size.
if required the covers can be cut to size.
N/A:
Day/Night Setting:
The PIR can operate 24Hrs a day or night mode (Low Level Conditions
<10Lux).To select night only mode, remove the cover from the bottom of the
PIR and press the "LUX" button as shown below.
Up to Six remote control units can be paired with each
HomeEasy Receiver socket or module, to pair the
outdoor PIR with a receiver unit,remove the battery
cover and, slide the switch to DEL.
Deleting Remote Control:
To delete the PIR from the memory of a HomeEasy remote control receiver
socket or module, simply press the "Learn" button.The LED will start to blink;
slide the "LEARN" switch to "DEL", the LED will blink twice to confirm that the
remote control has been removed from the receiver sockets memory.
Pairing/Deleting with Remote Control:
Now press the "Learn" button,the LED will start to flash, now slide the
"LEARN" switch to "SET", the units are now paired together.
Example