C-Data FD1204S User manual

Company Address: Flat 6, Bldg 4,South 2 of Honghualing Industrial Zone,Liuxian Road, Xili Town, Shenzhen, Guangdong, China(518055)
Factory Address: Fl1, Bldg B, Wentao Industrial zone, Yingrenshiyongxin Village, Shiyan Street, Baoan district, Shenzhen, Guangdong, China (518055)
Tel: [phone] Fax:[phone]
Website: www.cdatatec.com
EPON OLT Products User Manual
FD1204S/FD1208S/FD1216S/FD8000-L116
---Configration Guide
Version：V1.2

Company Address: Flat 6, Bldg 4,South 2 of Honghualing Industrial Zone,Liuxian Road, Xili Town, Shenzhen, Guangdong, China(518055)
Factory Address: Fl1, Bldg B, Wentao Industrial zone, Yingrenshiyongxin Village, Shiyan Street, Baoan district, Shenzhen, Guangdong, China (518055)
Tel: [phone] Fax:[phone]
Website: www.cdatatec.com
© Statement
Copyright © 2017 Shenzhen C-Data Technology Co., Ltd. All Rights Reserved. No part
of this manual may be reproduced or transmitted in any form or by any means
without the prior written consent.
The information in this document may be update at any time due to product
versions upgrade or any other reasons. Unless otherwise agreed, this manual
is for reference only. All statements, information and recommendations in this
manual do not constitute the warranty of any kind, express or implied. Plea
se contact your suppliers to get the latest version of this document.
About This Manual
This manual is applicable to C-Data FD1204S、FD1208S、FD1216S、FD8000-L116 EPO
N OLT products quickly installation configuration guide, Is the user to quickly
and easily manage EPON OLT equipment should read the information before.
guidelines.
The related documents for EPON OLT device are:
《FD1204S/FD1208S/FD1216S/FD8000-L116 User Manual-Device Installation User Ma
nual》
《FD1204S/FD1208S/FD1216S/FD8000-L116 User Manual- CLI Operation User Manua
l》
《FD1204S/FD1208S/FD1216S/FD8000-L116 User Manual- Configuration Guide》

Company Address: Flat 6, Bldg 4,South 2 of Honghualing Industrial Zone,Liuxian Road, Xili Town, Shenzhen, Guangdong, China(518055)
Factory Address: Fl1, Bldg B, Wentao Industrial zone, Yingrenshiyongxin Village, Shiyan Street, Baoan district, Shenzhen, Guangdong, China (518055)
Tel: [phone] Fax:[phone]
Website: www.cdatatec.com
Content
1 Instruction ..............................................................................................................................1
Document Scope ...............................................................................................................1
Revision History.................................................................................................................1
Proper Noun......................................................................................................................1
Note...................................................................................................................................2
2 OLT Login Manage ..................................................................................................................2
2.1 OLT Login Manage Explanation ...................................................................................2
2.2 OLT Login By Console...................................................................................................2
2.3 OLT Login By Telnet......................................................................................................3
3 OLT Upgrade...........................................................................................................................4
4 OLT WEB Management...........................................................................................................6
5 Configure Service In OLT Discrete Mode（Non-Template）.................................................7
5.1 FTTH Service Topology ................................................................................................7
5.2 Data Plan .....................................................................................................................8
5.3 Config Guide................................................................................................................8
5.4 Configure OLT Service..................................................................................................9
5.4.1 Configure OLT Global Vlan................................................................................9
5.4.2 Configure OLT GE Port Service Vlan .................................................................9
5.4.3 Configure OLT PON Port Service Vlan.............................................................11
5.4.4 Configure OLT Multicast Service.....................................................................12
5.5 Check ONU Register Status. ......................................................................................12
5.6 Configure Bridge ONU(SFU) Service..........................................................................12
5.6.1 Configure Bridge Onu(SFU) Internet Service..................................................12
5.6.2 Configure Bridge Onu(SFU) Multicast Service................................................13
5.7 Configure Gateway ONU（HGU）Service ................................................................14
5.7.1 Configure Gateway ONU（HGU）Internet Service--RTK Solution ................14
5.7.2 Configure Gateway ONU（HGU）Multicast Service--RTK Solution ..............15
5.7.3 Configure Gateway ONU（HGU）Internet Service--Broadcom Solution......16
5.7.4 Configure Gateway ONU（HGU）Multicast Service--Broadcom Solution ....20
5.7.5 Configure Gateway ONU（HGU）VOIP Service--Broadcom Solution ...........22
6 Configure Service In OLT Profile Mode.................................................................................26
6.1 Data Plan ...................................................................................................................26
6.2 Configure Process......................................................................................................27
6.3 Configure OLT Service................................................................................................27
6.3.1 Configfure OLT Globle Vlan ............................................................................27
6.3.2 Configure OLT GE Port Service Vlan ...............................................................27
6.3.3 Configure OLT PON Port Service Vlan.............................................................28
6.3.4 Configure OLT Multicast Service.....................................................................29
6.4 Create ONU Profile....................................................................................................29
6.4.1 Create ONU DBA Profile .................................................................................29
6.4.2 Create ONU Lineprofile ..................................................................................30
6.4.3 Create ONU Srvprofile....................................................................................30

Company Address: Flat 6, Bldg 4,South 2 of Honghualing Industrial Zone,Liuxian Road, Xili Town, Shenzhen, Guangdong, China(518055)
Factory Address: Fl1, Bldg B, Wentao Industrial zone, Yingrenshiyongxin Village, Shiyan Street, Baoan district, Shenzhen, Guangdong, China (518055)
Tel: [phone] Fax:[phone]
Website: www.cdatatec.com
6.5 Add ONU Manually....................................................................................................30
6.6 Check ONU Registration Status .................................................................................31
6.7 Configure Bridge ONU（SFU）Service .....................................................................31
6.7.1 Configure Bridge ONU(SFU) Internet Service.................................................31
6.7.2 Configure Bridge ONU(SFU) IPTV Service.......................................................32
6.8 Gateway ONU（HGU）Service Configure Introduction ...........................................33
7 Configure OLT QinQ Service .................................................................................................33
7.1 Data Plan ...................................................................................................................33
7.2 Configure Processes ..................................................................................................33
7.3 Configure OLT ............................................................................................................34
8 Common Command Description..........................................................................................34
Concluding Remarks...............................................................................................................35

Company Address: Flat 6, Bldg 4,South 2 of Honghualing Industrial Zone,Liuxian Road, Xili Town, Shenzhen, Guangdong, China(518055)
Factory Address: Fl1, Bldg B, Wentao Industrial zone, Yingrenshiyongxin Village, Shiyan Street, Baoan district, Shenzhen, Guangdong, China (518055)
Tel: [phone] Fax:[phone]
Website: www.cdatatec.com
1
1 Instruction
Document Scope
Reading Object
Product
Products Software
Version
C-DATA Employees,
FTTX
Operation&Maintenanc
e Engineer,
C-DATA Customer’s
Technical Engineer
Cdata EPON OLT（FD1204S/FD1208S
/FD1216S/FD8000-L116）
V1.3.X
Compiling Department
C-Data Product Management Center
Technical Support Department
Document
Version
V1.2
Revision History
Date
Version
Description
Author
2017-12-7
V1.1
OLT version switch to V1.2.X, cli
command line have been
changed.,update config guide fully
Technical Support
Department
2018-3-4
V1.2
1.OLT version switch to V1.3.X, cli
command line have been
changed,update config guide fully
2.Add FD8000-L116 config instruction
Technical Support
Department
Proper Noun
Acronym
Full name
Instructions
EPON
Gigabit-Capable Passive Optical
Network
Gigabit-Capable Passive Optical Network
OLT
Optical Line Terminal
Optical Line Terminal
ONU
Optical Network Terminal
Optical Network Terminal
OMCI
ONU Management and Control
Interface
GPON OLT&ONU Management and
Control Interface(protocol)
OAM
Operation Administration and
EPON OLT&ONU Operation Administration

Company Address: Flat 6, Bldg 4,South 2 of Honghualing Industrial Zone,Liuxian Road, Xili Town, Shenzhen, Guangdong, China(518055)
Factory Address: Fl1, Bldg B, Wentao Industrial zone, Yingrenshiyongxin Village, Shiyan Street, Baoan district, Shenzhen, Guangdong, China (518055)
Tel: [phone] Fax:[phone]
Website: www.cdatatec.com
2
Maintenance
and Maintenance Protocol
DBA
Dynamic Bandwidth Allocation
Dynamic Bandwidth Allocation
VLAN
Virtual Local Area Network
Virtual Local Area Network
VoIP
Voice over IP
Voice over IP
WLAN
Wireless Local Area Networks
Wireless Local Area Networks
FTTH
Fiber To The Home
Fiber To The Home
FTTB
Fiber To The Building
Fiber To The Building
Note
The command line described in the document is case sensitive in OLT.
If we meet a command that cannot be inputed or is prompted for error,we can input “?”to
see the latter command format.
Input incomplete commands can be completed by pressing the “Tab”key.
FD1204S、FD1208S、FD1216S are Pizza-Box OLT，only have one card，so,if we want to enter
PON mode,need input interface epon 0/0
FD8000-L116 is Plug-in card OLT,has four PON card,so the comamnd for entering PON mode
is OLT(config)# interface epon 0/<SlotID> ,SlotID is Slot Number,range is 1-4，for example,the
command for entering slot 1 is OLT(config)# interface epon 0/1
2 OLT Login Manage
2.1 OLT Login Manage Explanation
FD1204S、FD1208S、FD1216S support CLI,EMS and WEB management;CLI manege type divided
into telnet remote manage and console local manage, please check #2.2 and #2.3 chapter to see
concrete operations;please check EMS user manual to see EMS manage way;please check #4 to
see WEB manage way.
2.2 OLT Login By Console
First,find console port on OLT front surface,which is a RJ45 port.if want to login OLT by Console
port,we need do prepare as follows:
Need RJ-45-to-DB-9 serial line
Connect PC to OLT concole port,find COM number in “computer management”
Software for logining OLT by console port(Putty,SecureCRT)

Company Address: Flat 6, Bldg 4,South 2 of Honghualing Industrial Zone,Liuxian Road, Xili Town, Shenzhen, Guangdong, China(518055)
Factory Address: Fl1, Bldg B, Wentao Industrial zone, Yingrenshiyongxin Village, Shiyan Street, Baoan district, Shenzhen, Guangdong, China (518055)
Tel: [phone] Fax:[phone]
Website: www.cdatatec.com
3
parameter for console login software
Baud Rate:9600
Parity Check:None
Databit:8
Stopbit:1
Flow Control:None
Login OLT by console login software,then input username:root,password:admin
[OLT console connection diagram]
[OLT console connection device]
Port on Computer
Required Cable
Port on OLT
Serial Port
RJ-45 to DB-9 Console Cable
RJ-45 Console Port
USB Type-A Port
USB to RS-232 compatible serial port adapter ( Adapter may
require a software driver )
RJ-45 to DB-9 Console Cable
2.3 OLT Login By Telnet
There are two way to telnet,one is outband management,another is inband management.
1. Outband management(connect OLT MGMT port)
set PC ip as 192.168.1.X(except 192.168.1.100),PC connect to OLT MGMT port, login the OLT with

Company Address: Flat 6, Bldg 4,South 2 of Honghualing Industrial Zone,Liuxian Road, Xili Town, Shenzhen, Guangdong, China(518055)
Factory Address: Fl1, Bldg B, Wentao Industrial zone, Yingrenshiyongxin Village, Shiyan Street, Baoan district, Shenzhen, Guangdong, China (518055)
Tel: [phone] Fax:[phone]
Website: www.cdatatec.com
4
OLT default manage IP (default IP : 192.168.1.100). then input username and password,default
login username is root,password is admin.
Use command as follow can modify the outband management IP:
OLT> enable
OLT# config
OLT(config)# interface mgmt
OLT(config-interface-mgmt)# ip address 192.168.5.100 24
OLT(config-interface-mgmt)# exit
2. Inband management(connect OLT ge port)
First we login olt via console port or mgmt port, and add a vlanif for inband management,
assigned an IP address to this vlan,add the ge port to the vlan,ge port vlan mode can be access or
trunk,which depend on your network environment,then pc connect to OLT ge port（ge1-ge8）
and telnet to the OLT.
The way to set inband mangement ip as follows：
OLT> enable
OLT# config
OLT(config)# vlan 100
OLT(config)# interface ge
OLT(interface-ge)# vlan access 5 100 ----configure ge 5 as inband management port
OLT(interface-ge)# exit
OLT(config)# interface vlanif 100
OLT(interface-vlanif-100)# ip address 192.168.2.100 255.255.255.0
OLT(interface-vlanif-100)# exit
3 OLT Upgrade
1.Set up OLT update topology:
Use a PC as FTP server(run wftpd32.exe or Wftpd.exe in this pc),and connect to OLT mgmt port
or ge port to transmit firmware.

Company Address: Flat 6, Bldg 4,South 2 of Honghualing Industrial Zone,Liuxian Road, Xili Town, Shenzhen, Guangdong, China(518055)
Factory Address: Fl1, Bldg B, Wentao Industrial zone, Yingrenshiyongxin Village, Shiyan Street, Baoan district, Shenzhen, Guangdong, China (518055)
Tel: [phone] Fax:[phone]
Website: www.cdatatec.com
5
2.Test network connectivity
a.Connnect PC to OLT console port,used for updating OLT in boot mode.
b.Connect pc to OLT MGMT port or ge port,configure PC ip and OLT ip(inband ip or outband ip)
are in same segment.
c.PC can ping OLT manegemnet IP,if pc can ping OLT manegemnet ip,means OLT can connect to
FTP server.
d.Close PC firewall,prevent firewall intercept FTP software.
3. FTP server configuration
a.Open FTP software,configure FTP username and password,such as:admin/admin
b.Set up a directory of OLT updade files for the FTP server, such as the way for setting up the
wftp32. Exe software：
---Security -> User/Rights Security Dialog -> User Name —input admin
---Change Password —input admin
---Home Directory —set directory of OLT upgrade files

Company Address: Flat 6, Bldg 4,South 2 of Honghualing Industrial Zone,Liuxian Road, Xili Town, Shenzhen, Guangdong, China(518055)
Factory Address: Fl1, Bldg B, Wentao Industrial zone, Yingrenshiyongxin Village, Shiyan Street, Baoan district, Shenzhen, Guangdong, China (518055)
Tel: [phone] Fax:[phone]
Website: www.cdatatec.com
6
4.OLT update command
FD1216S、FD1208S、FD1204S、FD8000-L116 OLT need update two file,one is FW file,another
is Kernel file;if the boot file is too old,we need update boot file in OLT boot mode,boot upgrade
way will be provided separately.OLT the common upgrade method please see below:
a.Enter config view,input command as follows to update OLT kernel file(file name include
Kernel )
OLT(config)# load packetfile ftp 192.168.1.222 admin admin FD1216S_Kernel_X000_171114
_1833.img
Broadcast message from root:
Upgrade is in process.
File [FD1216S_Kernel_X000_171114_1833.img] download .......... OK
File [FD1216S_Kernel_X000_171114_1833.img] upgrade .......... OK
b.Input command as follows to update OLT FW file(file name include FW )：
OLT(config)# load packetfile ftp 192.168.5.234 admin admin FD1216S_FW_V1.3.1_X000_171
114_1841.img
Broadcast message from root:
Upgrade is in process.
File [FD1216S_FW_V1.3.1_X000_171114_1841.img] download .......... OK
File [FD1216S_FW_V1.3.1_X000_171114_1841.img] upgrade .......... OK
5.After update OLT,we need reboot OLT(Note:only reboot OLT,OLT can use new version)
OLT(config)# reboot
Please check whether data has saved, the unsaved data will lose if reboot system. Are you sure
to reboot system? (y/n)[n]:y
4 OLT WEB Management

Company Address: Flat 6, Bldg 4,South 2 of Honghualing Industrial Zone,Liuxian Road, Xili Town, Shenzhen, Guangdong, China(518055)
Factory Address: Fl1, Bldg B, Wentao Industrial zone, Yingrenshiyongxin Village, Shiyan Street, Baoan district, Shenzhen, Guangdong, China (518055)
Tel: [phone] Fax:[phone]
Website: www.cdatatec.com
7
1.First, update the WEB firmware via the #3 OLT upgrade way,(firmware name include Web word
,such as FD1216S_Web_V1.0.1_X000_171114_1841.img)
OLT(config)# load packetfile ftp 192.168.1.222 admin admin FD1216S_Web_V1.0.1_X000_17
1114_1841.img
2.PC connect to OLT mgmt port or inband management port,make sure PC can ping OLT inband
management ip or outband management ip
3.Open PC browser input OLT management ip,then we can see web login interface,web login
username and password is admin/admin：
5 Configure Service In OLT Discrete Mode（Non-Template）
This section mainly introduct FD1204S、FD1208S、FD1216S、FD8000-L116 internet service,
voice service and multicast service in discrete mode in FTTH environment.Mainly introduce the
bridge ONU(SFU and Home Gateway ONU (HGU),The following will introduce the service
configuration way for OLT and ONU according to two types ONU.
5.1 FTTH Service Topology

Company Address: Flat 6, Bldg 4,South 2 of Honghualing Industrial Zone,Liuxian Road, Xili Town, Shenzhen, Guangdong, China(518055)
Factory Address: Fl1, Bldg B, Wentao Industrial zone, Yingrenshiyongxin Village, Shiyan Street, Baoan district, Shenzhen, Guangdong, China (518055)
Tel: [phone] Fax:[phone]
Website: www.cdatatec.com
8
5.2 Data Plan
Main Data Plan List
Configuration Item
Data
VLAN Data
VLAN 100：Internet Service
VLAN 200：IPTV Service
VLAN 300：VOIP Service
OLT Port Setting
Ge5：VLAN 100 access mode
Ge6：VLAN 200 access mode
Ge7：VLAN 300 access mode
PON1：VLAN 100, VLAN 200, VLAN 300 trunk mode
ONU Register ID
Bridge ONU ID：1
Gateway ONU ID：2
Bridge ONU Port config
LAN 1：VLAN 100
LAN 2：VLAN 200
LAN3: VLAN 300 ---connect to VOIP phone
Gateway ONU Port config
Internet WAN：VLAN 100
IGMP WAN：VLAN 200
VOIC WAN：VLAN 300
5.3 Config Guide

Company Address: Flat 6, Bldg 4,South 2 of Honghualing Industrial Zone,Liuxian Road, Xili Town, Shenzhen, Guangdong, China(518055)
Factory Address: Fl1, Bldg B, Wentao Industrial zone, Yingrenshiyongxin Village, Shiyan Street, Baoan district, Shenzhen, Guangdong, China (518055)
Tel: [phone] Fax:[phone]
Website: www.cdatatec.com
9
5.4 Configure OLT Service
5.4.1 Configure OLT Global Vlan
In config mode,we can use OLT(config)# show vlan all to show the created vlan.
If the created vlan can’t meet the need,we can use command OLT(config)# vlan vlan-list to create
new vlan,According to the data plan, we create vlan100,vlan200,vlan300 firstly:
OLT(config)# vlan 100
OLT(config)# vlan 200
OLT(config)# vlan 300
5.4.2 Configure OLT GE Port Service Vlan
We can config GE port vlan mode as access,hybrid and trunk,we can configure different mode
according to our network plan, configure way of three mode as follows.
Configure GE 5,6,7 port vlan mode is access(in this document,GE port connect to PC,so we
configure ge port vlan mode as access):
OLT(config)# interface ge 0/0
OLT(config-interface-ge-0/0)# vlan mode 5-7 access
OLT(config-interface-ge-0/0)# vlan access 5 100
OLT(config-interface-ge-0/0)# vlan access 6 200
OLT(config-interface-ge-0/0)#vlan access 7 300
OLT(config-interface-ge-0/0)# exit
Configure GE 5、6、7口vlan mode is trunk：
Create OLT Global Vlan
Create OLT GE Port Vlan
Create OLT PON port vlan
Create ONU Port Vlan
Save OLT Configration
Start
End

Company Address: Flat 6, Bldg 4,South 2 of Honghualing Industrial Zone,Liuxian Road, Xili Town, Shenzhen, Guangdong, China(518055)
Factory Address: Fl1, Bldg B, Wentao Industrial zone, Yingrenshiyongxin Village, Shiyan Street, Baoan district, Shenzhen, Guangdong, China (518055)
Tel: [phone] Fax:[phone]
Website: www.cdatatec.com
10
OLT(config)# interface ge 0/0
OLT(config-interface-ge-0/0)# vlan mode 5-7 trunk
OLT(config-interface-ge-0/0)# vlan trunk 5 100
OLT(config-interface-ge-0/0)# vlan trunk 6 200
OLT(config-interface-ge-0/0)#vlan trunk 7 300
OLT(config-interface-ge-0/0)# exit
Configure GE 5、6、7口vlan mode is hybrid：
OLT(config)# interface ge 0/0
OLT(config-interface-ge-0/0)# vlan mode 5-7 hybrid
OLT(config-interface-ge-0/0)# vlan hybrid 5 tagged 100
OLT(config-interface-ge-0/0)# vlan hybrid 6 tagged 200
OLT(config-interface-ge-0/0)# vlan hybrid 7 tagged 300
OLT(config-interface-ge-0/0)# exit
NOTE：
The OLT vlan handle process as follows:
Vlan mode
Direction
Message have
vlan tag or not
Handling method
Access mode
In
vlan tag
Discard
untag
Add port configured vlan in access mode for
message (main parameter is VID),and forword
Out
vlan tag
Forward message to the corresponding port
according to VID and remove vlan tag;If the
VLAN ID of the Tagged message is not same to
the port VID, it is discard.
untag
Discard
Trunk mode
In
vlan tag
If the VLAN in the message is permit to pass
port, it will be forwarded directly; If the VLAN
in the message doesn’t permit to pass port, it
is discarded.
untag
Add default vlan(native-vlan) for untagged
message and forward.
Out
vlan tag
If the VLAN in the message is permit to pass
port, it will be forwarded directly; If the VLAN
ID of the message is the default (native-
VLAN)VLAN, then the VLAN tag is discard and
forward;If the VLAN in the message doesn’t
permit to pass port, it is discarded.

Company Address: Flat 6, Bldg 4,South 2 of Honghualing Industrial Zone,Liuxian Road, Xili Town, Shenzhen, Guangdong, China(518055)
Factory Address: Fl1, Bldg B, Wentao Industrial zone, Yingrenshiyongxin Village, Shiyan Street, Baoan district, Shenzhen, Guangdong, China (518055)
Tel: [phone] Fax:[phone]
Website: www.cdatatec.com
11
untag
Discard
Hybrid mode
In
vlan tag
If the VLAN in the message is permit to pass
port, it will be forwarded directly; If the VLAN
in the message doesn’t permit to pass port, it
is discarded.
untag
Add default vlan(native-vlan) for untagged
message and forward.
Out
vlan tag
If the VLAN in the message is permit to pass
port,according vlan tag or vlan untag of
message to discard or no discard vlan
tag,then forward message,If the VLAN ID of
the message is the default (native-VLAN)
VLAN, then the VLAN tag is discard and
forward; If the VLAN in the message doesn’t
permit to pass port, it is discarded.
untag
Discard
5.4.3 Configure OLT PON Port Service Vlan
We can config PON port vlan mode as access,hybrid and trunk,according to our network plan
configure different mode,if message from ONU is untag,we can configure PON port vlan mode is
access or hybrid untag mode;if message from ONU is tag,we can configure PON port vlan mode is
trunk or hybrid tag mode; configure way as follows.
Config PON1 port vlan mode is access:
OLT(config)# interface epon 0/0
OLT(config-interface-epon-0/0)# vlan mode 1 access
OLT(config-interface-epon-0/0)# vlan access 1 100
OLT(config-interface-epon-0/0)# exit
Config PON1 port vlan mode is trunk:（PON port is trunk mode in this document）:
OLT(config)# interface epon 0/0
OLT(config-interface-epon-0/0)# vlan mode 1 trunk
OLT(config-interface-epon-0/0)# vlan trunk 1 100,200,300
OLT(config-interface-epon-0/0)# exit
Config PON1 port vlan mode is hybird:
OLT(config)# interface epon 0/0
OLT(config-interface-epon-0/0)# vlan mode 1 hybrid
OLT(config-interface-epon-0/0)# vlan hybrid 1 tagged 100,200,300
OLT(config-interface-epon-0/0)# exit

Company Address: Flat 6, Bldg 4,South 2 of Honghualing Industrial Zone,Liuxian Road, Xili Town, Shenzhen, Guangdong, China(518055)
Factory Address: Fl1, Bldg B, Wentao Industrial zone, Yingrenshiyongxin Village, Shiyan Street, Baoan district, Shenzhen, Guangdong, China (518055)
Tel: [phone] Fax:[phone]
Website: www.cdatatec.com
12
5.4.4 Configure OLT Multicast Service
Configure IGMP and multicast-vlan 200
OLT(config)# igmp mode snooping
OLT(config)# multicast-vlan 200
OLT(config-multicast-vlan-200)# igmp program add program-index 1 ip 224.3.3.3
OLT(config-multicast-vlan-200)# igmp router-port ge 0/0/6
OLT(config-multicast-vlan-200)# btv
OLT(config-btv)# igmp user add user-index 1 pon 0/0/2 ont 2 vlan 1000 no-auth
OLT(config-btv)# multicast-vlan 200
OLT(config-multicast-vlan-200)# igmp member user-index 1
OLT(config-multicast-vlan-200)# exit
NOTE：
igmp program add program-index command is used to create multicast program table. Only the
program table in the multicast vlan, the user can watch the program. Create multicast program
table can use igmp program add program-index <1-2000> batch command to batch add program
or use igmp program add program-index <1-2000> ip command to add program single.
5.5 Check ONU Register Status.
In OLT discrete mode,ONU is automatically registered,after ONU is automatically registered,use
command show ont info to query ONU online status.make sure ONU “Control flag”is“Active”,“Run
State”is“Online”,“Config state”is“Success”and“Match state”is“Match”
OLT(config-interface-epon-0/0)# show ont info 1 all
-----------------------------------------------------------------------------
F/S P ONT MAC Control Run Config Match Desc
ID flag state state state
----------------------------------------------------------------------------
0/0 1 1 E0:67:B3:09:F0:21 active online success match
0/0 1 2 E0:67:B3:12:05:3E active online success match
----------------------------------------------------------------------------
Total: 2, online 2
5.6 Configure Bridge ONU(SFU) Service
In OLT discrete mode,we need enter OLT to config ONU one by one,config way as follows:
5.6.1 Configure Bridge Onu(SFU) Internet Service
Premise condition of ONU to open internet service:
OLT connect to uplink device and open internet service

Company Address: Flat 6, Bldg 4,South 2 of Honghualing Industrial Zone,Liuxian Road, Xili Town, Shenzhen, Guangdong, China(518055)
Factory Address: Fl1, Bldg B, Wentao Industrial zone, Yingrenshiyongxin Village, Shiyan Street, Baoan district, Shenzhen, Guangdong, China (518055)
Tel: [phone] Fax:[phone]
Website: www.cdatatec.com
13
OLT have created vlan for internet service
OLT have configured GE port vlan
OLT have configured PON port vlan
ONU have registered
SFU ethernet port vlan mode have transparent,tag(access),trunk mode and so on,we can according
to our network plan configure different mode.all onu vlan is configured by OLT,configure way as
follows:
Configure ONU1 eth1 vlan mode is tag(access) (ONU eth port vlan mode is tag in this document):
OLT(config)# interface epon 0/0
OLT(config-interface-epon-0/0)# ont port native-vlan 1 1 eth 1 vlan 100
OLT(config-interface-epon-0/0)# exit
Configure ONU1 eth1 vlan mode is transparent:
OLT(config)# interface epon 0/0
OLT(config-interface-epon-0/0)# ont port vlan 1 1 eth 1 transparent
OLT(config-interface-epon-0/0)# exit
Config ONU1 eth1 vlan mode is trunk:
OLT(config)# interface epon 0/0
OLT(config-interface-epon-0/0)# ont port vlan 1 1 eth 1 100
OLT(config-interface-epon-0/0)# exit
5.6.2 Configure Bridge Onu(SFU) Multicast Service
Premise Condition
OLT connect to uplink device and open service
OLT have created vlan for multicast service
OLT have configured GE port vlan
OLT have configured PON port vlan
ONU have registered
In OLT discrete mode,we need enter OLT to config ONU multicast service,configure way as follows:
Configure ONU1 multicast vlan mode is snooping,ONU1 eth2 vlan is 200,and multicast vlan mode
is untag:
OLT(config)# interface epon 0/0
OLT(config-interface-epon-0/0)#ont multicast-mode 1 1 igmp-snooping
OLT(config-interface-epon-0/0)#ont port attribute 1 1 eth 2 multicast-tagstrip untag
OLT(config-interface-epon-0/0)# ont port multicast-vlan 1 2 eth 2 200
OLT(config-interface-epon-0/0)# exit
----End

Company Address: Flat 6, Bldg 4,South 2 of Honghualing Industrial Zone,Liuxian Road, Xili Town, Shenzhen, Guangdong, China(518055)
Factory Address: Fl1, Bldg B, Wentao Industrial zone, Yingrenshiyongxin Village, Shiyan Street, Baoan district, Shenzhen, Guangdong, China (518055)
Tel: [phone] Fax:[phone]
Website: www.cdatatec.com
14
5.7 Configure Gateway ONU（HGU）Service
Gateway ONU（HGU）can provide internet,VOIP,IPTV service for FTTH,support PPPOE/DHCP
dial-up,NAT，IGMP.Because HGU have route function, ONU service need to be configured with the
local web or tr069,include wan and vlan configuration,don’t need configure vlan in olt,only make sure
ONU can register to OLT.OLT don’t support configure ONU route wan,specific configure as follows:
5.7.1 Configure Gateway ONU（HGU）Internet Service--RTK Solution
premise condition
OLT connect to uplink device and open service
OLT have created vlan for internet
OLT have configured GE port vlan
OLT have configured PON port vlan
ONU have registered
1.Create route wan and bind LAN1 in onu web
Click InternetInternet ConfigWAN Config
NOTE：

Company Address: Flat 6, Bldg 4,South 2 of Honghualing Industrial Zone,Liuxian Road, Xili Town, Shenzhen, Guangdong, China(518055)
Factory Address: Fl1, Bldg B, Wentao Industrial zone, Yingrenshiyongxin Village, Shiyan Street, Baoan district, Shenzhen, Guangdong, China (518055)
Tel: [phone] Fax:[phone]
Website: www.cdatatec.com
15
Mode select Route. Check Enable VLAN and Vlan ID input 100. Service Mode select INTERNET.
Bind port check Port_1 and wireless(SSID).
Internet service take DHCP mode as an example in this document. The service type please select
suitable type according to the user's actual environment. ONT detail usage please refer to ONT user
manual.
2. Check ONU internet wan status
Click StatusInternet Info
5.7.2 Configure Gateway ONU（HGU）Multicast Service--RTK Solution
premise condition
OLT connect to uplink device and open multicast service
OLT have created vlan for multicast
OLT have configured GE port multicast vlan
OLT have configured PON port multicast vlan
ONU have registered
1. Create bridge wan and bind LAN2 in onu web
Click InternetInternet ConfigWAN Config
NOTE：

Company Address: Flat 6, Bldg 4,South 2 of Honghualing Industrial Zone,Liuxian Road, Xili Town, Shenzhen, Guangdong, China(518055)
Factory Address: Fl1, Bldg B, Wentao Industrial zone, Yingrenshiyongxin Village, Shiyan Street, Baoan district, Shenzhen, Guangdong, China (518055)
Tel: [phone] Fax:[phone]
Website: www.cdatatec.com
16
Mode select to Bridge. Check Enable Vlan,Vlan ID input 200. Service Mode select Other.Bind port
click Port_2.
2. Config IGMP mode in ONU web
Click ApplicationIGMP ConfigIGMP Snooping. Enable IGMP Snooping.
3.Configure multicast vlan on ONU web
Click ApplicationMulticast Vlan3_Other_B_VID_200Modify. Input 200 behind VLAN
multicast(blank said set).
4.Check ONU multicast wan status
Click StatusInternet Info
----end
5.7.3 Configure Gateway ONU（HGU）Internet Service--Broadcom Solution
premise condition
OLT connect to uplink device and open internet service
OLT have created vlan for internet
OLT have configured GE port vlan
OLT have configured PON port vlan
ONU have registered