Ca'Bano 30304 User manual

BS01981726
BS02621727
BS01981726
l. Installation Notice
1. Please lay water pipes in accordance with this manual.
2. Floor drain should be installed on the site.
3. The product should be installed only after the completion of house
interior decoration in case the paint or other chemicals erode the
mixer surface.
4. Clean pipes to get rid of mud, sand or other debris blocked in pipes
before installation.
5. Check whether the threads can be matched. Otherwise, installing
forcefully will damage the components.
6. After installation, check all the joints to make sure they are firmly
connected. Run the water. Turn on and off repeatedly to ensure no
leaking problem. After that, the product is ready for normal use.
7. Hand the manual to users.
II. Operation Notice
1. The product is used under water pressure 0.05~1.0 MPa, water
temperature 4~90°C.
2. Do not hang heavy things on the product.
3. Remember to turn off the mixer if no water comes out of it
(Especially when nobody in the house or during the decoration period).
4. Clean the surface of the product regularly to keep it glossy. Note: Please
do not use inappropriate tools such as sharp brushes, rough sponges,
scouring pads or corrosive detergent. And it is not recommend to use the
detergent sold in the market, because its formula changes frequently.
Please clean the product with wet cloth and soapy water after usage.
Then rinse the soap off with clean water and dry with a soft cotton cloth.
5. When indoor temperature drops below 0°C, take necessary measures
(Keep the product warm, close windows) to prevent the product from
frost cracking (Especially when windows open for air ventilation while
nobody in the house).
6. Adjust the temperature before use to avoid scald.
7. Do not disassemble the product without help from the professionals.
lll. Installation Diagram
IV. Installation Steps(Fig.1-21)：The installation diagram is only for reference.
The product is subject to the real object.
S2.5 Wrench (supplied)
Prepare and check the
following tools.
Spanner
Philips
Screwdriver
Protection Sheath
Stop Collar
Inlet Valve Body
Plastic Spacer
Locking Washer
Locking Nut
Remove the protection sheath
off the two inlet valve bodies.
Take off the stop collar and
screw off the locking nuts to
the bottom.
#30304
4 Piece deck mount tub ller with hand shower
INSTALLATION GUIDE
Last revision: October 23rd

Bathtub Deck
Outlet
Outlet
Place the two inlet valve
bodies (red on the left
and blue on the right)
upward through the
bathtub deck with the
outlet holes facing against
each other. Tighten on the
stop collars and put on the
protection sheath.
Rubber Washer
Locking Washer
Locking Nut
Ø26 O-Ring
Ø26 O-Ring
Inlet Adapter
Washer
Hex Nut
Lift Rod
Base
Take off the following
from the lift rod base
accordingly: the hex
nut, washer,
Ø 26 O-
Ring, inlet adapter,
locking nut, locking
washer and rubber
washer.
Setscrew
Protection Sheath
Place the lift rod base
downward through the
bathtub deck. Then put
on the rubber washer
and locking washer,
tightened by locking nut
and setscrew. Then put
back the parts that were
dismantled before.
Remove the protection
sheath from the inlet
adapter .
Ø16 O-Ring
Connecting Rod
Connecting Nut
Ø16 O-Ring
Washer
Use the connecting rod
to connect the two inlet
valve bodies with the
inlet adapter. Tighten
the connecting nuts.
Setscrew
Tighten the locking nuts
and setscrews on the
inlet valve bodies.
Protection Sheath
Hand Shower Seat
Rubber Washer
Locking Washer
Locking Nut
Take off the locking nut,
locking washer, rubber
washer and protection
sheath from the hand
shower seat.
Circlip
Knitted Hose
Take the circlip off the knitted
hose. Put the smaller end of
the knitted hose upward
through the hand shower
seat and put back the circlip.

Setscrew
Pass the hand shower
seat downward through
the bathtub deck. Put on
the rubber washer and
locking washer. Put back
the locking nut and
tighten it with setscrew.
Balance Weight
Connect the knitted
hose to the lift rod
base. Install the
balance weight at
a proper position in
the knitted hose and
make sure the hose
could be completely
pulled out of the
hand shower seat.
Turn off the valves
and run water for
pressure test to
ensure there is no
leakage. Make sure
hot water is
connected to the left
valve body and cold
water to the right.
Cold water
Hot water
Turn on the valves
and run water for
pressure test to
ensure there is no
leakage. Then put
back the protection
sheath to the
hand shower seat .
Hex Nut
Decorating Ring (small)
Protection Sheath
Remove the protection
sheath and put on the
decorating ring. Tighten
it with the hex nut.
Handle
Screw
Spacer Blue
Install the spacer and
then handles (attention
to the red mark on the
left and blue on the
right) and tighten the
screws on the handles.
Cap
M5 Screw
Loosen the M5 screw and
take off the cap.
Rod Cap
Body
M5 Screw
Decorating Ring (big)
Place the decorating
ring and the body onto
the lift rod base one by
one. Tighten them with
two M5 screws. Then
insert the rod cap into
the slot in the back of
the body to connect
with the lift core.
Red

Hand shower
Shower hose
Shower Holder
M5 Screw
Decorating Ring (small)
Put the decorating ring
onto the hand shower
seat. Connect the
shower hose with the
hand shower. Pass the
hose downward through
the shower holder to
connect with the knitted
hose. Remove the circlip
off the knitted hose and
connect the shower
holder to the hand
shower seat. Tighten
them with M5 screw.
After installation,
check if everything is
complete. The diagram
shows the default
bathtub outlet when
the handles are
turned on.
When the rod cap
is lifted, water comes
out of the hand
shower.
Spout
The spout can
rotate 360 degrees.
V. Maintenance
Spout
Filter
Inner Core
S2.5 Wrench
M5 Screw
After a period of usage, if the volume lessens, it might be due to debris from
bad quality water blocking the inner core. Loosen the M5 screw and take out
the spout and then the inner core. Clean its filter with clean water.
Then install it back.