Ca'Bano 30311 User manual

BS81081841
I. Installation Notice
1.Install water pipes in accordance with this manual.
2.Floor drain should be installed in the location of the faucet.
3.Rough-in box should be installed before ground construction. The
associated mixer should be installed after the ground construction. The
rough-in box on the inlet base shall not be cut or removed, and shall be
protected to avoid damage to each rough-in box and inlet base during
construction.
4.Clean pipes before installation to get rid of mud,sand or other debris.
5.If the thread of pipes don’t match well with product, please find out the
reason first, otherwise a forced connection will damage the faucet.
6.After installation, check all the joints to ensure they are firmly connected.
Then keep water flow. Turn on and off repeatedly to ensure there is no
leakage around the joints.At this stage, the product is ready for normal use.
7.Keep the manual to the user.
II.Operation Notice
1.The working condition of this product is water pressure 0.05~1.0MPa,
water temperature 4~90°C.
2.Do not hang heavy things on the faucet.
3.Make sure the faucet is off when no water comes out of it, especially when
nobody resides in or during the period of decoration or suspend of water.
4.Regularly clean the surface of faucet to keep it bright. Attention: do not use
inappropriate tools such as sharp brushes, rough sponges, scouring pads
or corrosive detergent to clean the faucet. It is not recommended to use
the detergent sold in the market, because its formula changes frequently.
Please clean the faucet by a wet cotton cloth with soapy water, then rinse
and dry with a soft cotton cloth after each time of usage.
5.When the room temperature drops to below 0°C, take necessary measures
(such as keeping faucet warm and closing windows) to prevent the faucet
from being frozen or even broken (especially when windows kept open for
air ventilation while nobody resides in).
6.Please open the cold and hot water in turn and adjust to comfortable
temperature before use to avoid scald.
7.Do not disassemble the product without the help from the professionals..
III.Installation Diagram
IV. Installation Steps(Fig.1-19)：The installation diagram is only for reference.
The product is subject to the real object.
Prepare and check
the following tools.
Drill Goggles Spanner
Teflon Tape
Level
Silicone
Sealant Pencil Saw Blade
S6 Wrench
(supplied)
S5 Wrench
(supplied)
S4 Wrench
(supplied)
S2.5 Wrench
(supplied)
Mark position based on the mounting
holes of the rough-in base and drill
four
Ø 8 holes. (Attention the “HOT”
mark on the rough-in base is hot water
inlet should face towards the bathtub.)
M8 Screw
Mounting hole
Rough-in base
Ø 8 hole
Last revision: November 13th
#30311
Floor mount tub ller with hand shower
INSTALLATION GUIDE

Hex nut
Spring shim
Washer
Expansion bolt
Install four expansion bolts into the
rough-in base and tighten hex nuts.
Teflon Tape
Hot feeding pipe
Cold feeding pipe
Wrap the coupling with
Teflon tape and connect
it to the rough-in base.
Then connect inlet pipes
of proper length.
Towards bathtub
Insert expansion bolts into Ø 8 holes.
(Attention
the “HOT” mark on the
rough-in base is the hot water inlet
should face towards the bathtub
)
Level
Level
M8 Screw
Adjust M8 screws on the rough-in
base to its level position. When
bubbles inside the level are in the
center of the circle, the rough-in
base is at level position, and then
tighten hex nuts.
Rough-in box
Silicone sealant
Fill silicone sealant in between
the rough-in box and finish
floor such as tiles.
Reference of
finished floor
For floor work, make sure the center of
inlet pipes to finished floor is between
28-50mm.
Cover
Remove the cover and run
water for pressure test.
Check all joints to make
sure no leakage. Then put
back the cover.
Hot feeding pipe
Cold feeding pipe
Flush Water
Flush Water
Run water to get rid
of any debris inside
pipes. Connect cold
and hot water pipes.
Attention that the
HOT mark is to the
hot water pipe and
COLD mark to the
cold pipe.

Cut the excessive part of
the rough-in box. Keep the
top edge of the rough-in
box about 10 mm above
the finished floor. Saw blade
Rough-in box
Flange
Locking screw
Base plate
Plug
Remove the locking screws
byS5 wrench, take out the
flange and base plate, pull
out the plugs.
Cold water outlet
Inner core
Wrench socket
Blue mark
Red mark
Towards bathtub
Hot water outlet
Make sure the inner core is
at the position as shown in
the diagram. The hot water
outlet should face towards
the bathtub.
If the inner core is not at the
correct position as shown in the
diagram 13, please adjust the
inner core with a S6 wrench.
S6 Wrench
(supplied)
Inner core
Take off protection
sheath from inner pipe
of faucet body, put on
escutcheon carefully
to avoid scratch to the
surface of faucet body.
Fix flange (the side with
counter bore back
against faucet body)
with locking screws to
faucet body firmly.
Faucet body
Inner pipe
Protection sheath
Escutcheon
Flange
Level
S5 Wrench
(supplied)
Locking
screw
Connect the inlet pipe of the
faucet body into the outlet
hole of the inner core
vertically ((attention to the
hot (red) and cold (blue)
correspondence)). The spout
of the faucet is against the
bath. Fix the faucet body
on the rough-in base with
locking screws. Adjust the
faucet body by level. Tighten
the locking screws directly
if the faucet body is upright.
Otherwise, adjust the M8
screws on the flange until the
faucet body is upright, then
tightening the locking screws.
Press the escutcheon down
on the floor.
S4 Wrench
(supplied)
M8 Screw

Hand shower
Hose
Connect hand shower and
faucet body with hose.
After installation, flush
water to check if the
installation is proper.
The diagram shows
the product when it is
turned on, the default
outlet is spout.
Diverter
Lift up diverter, water
runs from hand shower
( if the diverter lose
function because of
low water pressure,
lift up diverter and
rotate it 90° in any
direction).
V. Maintenance(Fig.20):
If the hot and cold feeding pipe is found to be connected in reverse after
installation, use S6 wrench to turn the inner core 180° to make the cold and
hot water reverse connection (Unload the faucet body first).