Cabela's Clam QUICK-SET User manual

Part #: 109863
Center Height: 94 inches
Foot Print: 110 total square feet
Hub-to-Hub: 150 x 150 inches
Weight: 41 lbs.
Instruction #: 104798
Please contact customer service directly at the E-mail or phone number listed below for any
quality issues. ONCE USED THIS PRODUCT CANNOT BE RETURNED TO STORE.
** Warranty cannot be honored without an original, dated receipt. **
Customer Service Hours: Monday –Friday 9am –4pm Central Standard Time
Phone: [phone]
Email: [e-mail]
IMPORTANT! Please read: This product is warrantied to the original retail purchaser (not transferable) to be free from
manufacturer’s defects for one (1) year from the date of the original purchase. Warranty does not cover screen tears,
tent tears, or broken or bent poles due to high wind, weather conditions or unattended use. The part will be replaced or
repaired (manufacturer’s option) if found defective within the one (1) year time frame. Warranty will be void if product
has been subject to neglect, misuse, improper installation, misapplication, alteration, or accident including, but not
limited to, improper maintenance or use of unauthorized parts or attachments. Please read this entire owner’s manual
to ensure proper installation, use, storage and care for your Clam shelter.
To submit a warranty request, please use one of the following methods:
Preferred Method - Visit www.QuickSetShelters.com under the “Customer Support” tab fill out the warranty
form.
Email: [e-mail]
Write: Clam Outdoors - Warranty Department
o12135 Brockton Lane N.
oRogers, MN 55369
Information needed to submit a warranty claim: Please include your full name, address, phone number, a copy of your
receipt, a brief description of the problem, and pictures to clearly show the area(s) of concern. Clam’s warranty
department will review your request and a Clam representative will contact you regarding your claim status. If
instructed by the warranty department, all returns must be returned with postage prepaid.
It is expressly understood that Clam Corporation’s liability for its products, whether due to breach of warranty,
negligence, strict liability, or otherwise, is limited to the repair of the product as stated above. Clam Corporation is not
liable for any injury, loss, damage, or expense, whether direct or consequential, including but not limited to loss of use,
income, profit, or damage to material arising in connection with the sale, installation, use of, inability to use, or the
repair or replacement of Clam Corporation products. Clam Corporation reserves the right to make alterations or
modifications in its products at any time, which in its opinion, may improve the performance and efficiency of the
product. Clam shall not be obligated to make such alterations or modifications to products already in service.
WARRANTY INFORMATION
LIMITATION OF LIABILITY
QUICK-SET SCREEN TENT
Model #: 9863

BEFORE ATTEMPTING TO USE THIS
PRODUCT: Go to
www.QuickSetShelters.com, click on your
shelter model and watch the set up video
provided. Then practice setting up and
taking down at home. Repeat several times
until comfortable.
Please fully understand and follow all safety
instructions outlined in this booklet. Failure to do so
could result in severe injury.
• Do not use open flame heaters in your
screen tent.
• Tent fabric will melt when contact is made with
hot surfaces (i.e., heaters).
• Use external tie-downs and stakes during excessive
wind conditions(15+mph)
WARNING
Injury or death may result from fire if tent fabric is
exposed to open flame.
Tent fabric is not fireproof. Fabric will burn with
extended exposure to open flame. Do not use open
flame products inside tent. Tent fabric is treated with
fire retardant. Application of any foreign substance may
render the flame retardant properties ineffective.
This tent is made with flame resistant fabric which meets
CPAI-84 specifications.
Item #
Qty.
Part #
Description
1
5
105153
Hub & Pole Kit Walls (4 Poles & 1 Hub)
2
1
105152
Hub & Pole Kit Roof (6 Poles & 1 Hub)
3
1
104671
Carry Bag
4
7
104173
Stake, Screen Hub
5
5
102458
Tie Down Rope
6
2
104795
Aluminum Awning Support Pole
7
2
104796
Aluminum Door Support Pole
8
1
104797
Fiberglass Awning Support Pole
9
1
104670
Instructions/Owner’s Manual
Replacement parts can be ordered on-line at www.QuickSetShelters.com.
IMPORTANT: When you first open your shelter, you will see the poles on the OUTSIDE of the shelter.
Once set up, the poles should be on the INSIDE of the tent. Your screen tent is folded in half for storage.
Only pull outward on the hub pull (loops) on the exterior of the tent.
Please follow the directions carefully for proper set up and take down.
SAFETY INSTRUCTIONS
PARTS LIST
SET UP INSTRUCTIONS

Photo 3
Photo 5
Step 1: Unzip the storage bag completely and remove
the shelter. Use care not to misplace the instructions
and the stake and rope pouch. It is advised to store your
stakes, ropes and pouch in the carry bag until they’re
needed.
Step 2: Pick the tent up directly from the carry bag and
stand it on the center metal hub. (Photo 2)
Step 3: With the screen tent standing up on the black
center hub hold one corner of the material and let the
screen fall open until you see the roof lying flat with the
Cabela’s logo facing up. If it does not fall open naturally,
unfold the tent until you can see the roof panel lying
flat. At this point the poles should be on the inside of
the tent with the roof facing up. (Photo 3)
Step 4: With the poles on the inside, reach for the
handle at the center of one wall and pull until the
section pops out. Hold the roof line with the opposite
hand. (Photo 4)
Step 5: Continue around the shelter repeating the
previous step until all wall panels are erect.
Step 6: Enter through the door and push up on the
center ceiling hub until the ceiling pops up. (Photo 5)
SET UP INSTRUCTIONS CONTINUED
Photo 1
Photo 2

Step 7 (optional): Insert the vertical rods on either side of
the screen tent’s door. Install ends into the pockets at the
top and bottom of each side of the doorway. It is
recommended to use these if any wind is present. (Photos 6)
Step 8: Install securing stakes on the tent. The stakes are
designed to be used on the inside grommets or the outside
tie downs. If there is little to no wind, stakes may be used in
the eyelet in each corner of the screen tent. Place the tip of
the stake on the inside of the eyelet and drive it into the
ground so the hook catches the eyelet and holds the tent in
place.
If wind is present you must use the outside tie downs.
Secure the tent by tying one end of the provided strings on
each metal loop on the outside of the hub and staking the
other end. (Photo 8)
Using the built in Wind Panels:
Locate the tie strings mounted on each end of the wind
panels. Untie and let the panel fall down. Locate the hub
strap on the center of the wall and pull it through the
grommet on the wind panel. Zip down the zippers located on
each side of the wind panels. Finish with securing the Velcro
tabs on the outside of the zipper. To store the wind panels,
simply detach the Velcro tabs and unzip the wind panels.
Roll the panel back up and tie with tie strings.
Using the Awning Feature:
To use the awning feature on your screen tent, unzip the
zippers on each side of the attached wind panels. Install the
fiberglass pole into the pockets on each end of the lower,
bottom side of the wind panel. Using the aluminum poles
with the pins located at the top, install the pins through the
grommets at each corner. You can now attach a tie string
from the webbed loop at the corner of the wind panel and
run it to a stake approximately 3 ft out from the edge of the
awning. (Photos 8 & 9)
Photo 8
Photo 9
Photo 6
Photo 5

Photo 1
Step 1: Remove all the stakes from the interior and
exterior of the tent.
Step 2: If used, remove the vertical door support rods
from pockets at the bottom of the panel, pull apart, and
refasten them with the Velcro straps located diagonally
on the panels next to each side of the door. (Photo 1)
Step 3: Push in on the walls in from the outside of the
tent to collapse the wall panels. Do this to all wall
panels until the tent is collapsed. (Photo 2)
Step 4: Push down on one of the roof poles until the
roof is collapsed. (Photo 3)
Step 5: Once the shelter is completely collapsed grab
one corner of the tent and fold it in half on itself. Once
in half, you can now condense the shelter to fit into the
carry bag. (Photo 4)
Step 6: Carefully lift and insert into the carry bag. Pay
close attention not to twist or distort the hubs or fabric
while inserting into bag. Place stakes and tie down
ropes into their bag and place the stake bag into the
carry bag.
Photo 2
Photo 3
Photo 4
TAKE DOWN INSTRUCTIONS

Please fully understand and follow all safety instructions as outlined. Failure to do so could result in severe injury or
death.
Do NOT use open flame heaters in your screen tent. Injury or death may result from fire if tent fabric is exposed to
open flame. The tent is not fireproof, but the fabric is treated with a fire retardant that meets CPAI-84 specifications.
Application of any foreign substance may render the flame retardant properties ineffective. Fabric will melt when
contact is made with hot surfaces (i.e., heaters, propane stoves, etc.)
WARNING
Injury or death may result from fire if tent fabric is
exposed to open flame.
Tent fabric is not fireproof. Fabric will burn with
extended exposure to open flame. Do not use open
flame products inside tent. Tent fabric is treated with
fire retardant. Application of any foreign substance
may render the flame retardant properties
ineffective.
Night time: exterior reflectors must be visible to
reduce risk of collisions.
This tent is made with flame resistant fabric which
meets CPAI-84 specifications.
*For replacement parts, frequently asked questions, shelter information, videos, and all of your ice fishing or
screen tent needs visit our web site at www.QuickSetShelters.com.
SAFETY INFORMATION

Q: How do I set up my screen tent?
A: Please review the set up and take down instructions in your owner’s manual or go to
www.QuickSetShelters.com to watch an instructional video on the proper and simplest way to set up and take
down a screen tent. Videos can be found under your shelter’s model on our website.
Q: Do you offer any accessories for Quick-Set Screen Tents?
A: Yes! We carry other items that are great additions to your screen tent. Some of what we offer includes
fan/light combos, quick pack tables, LED hub lights and more! Check these accessories out at
www.QuickSetShelters.com.
Q: Is there anything that can be put on the outside of the tent to increase the water resistance?
A: Our screen tents are water resistant, not waterproof. You can use any waterproofing product you would
traditionally use on a tent to add an extra layer of protection. An example of this is “Camp Dry” which is sold in
most sporting goods stores. The seams have been stitched with waterproof taping but you may apply “Seam
Grip” to the seams of the shelter if you wish to add additional protection. Please be advised that applying
additional products to the shelter may alter the fire retardant properties.
Q: Can I use anything to increase the UV protection?
A: Our screen tents are treated with a UV protectant coating when they are manufactured. If you wish to add
additional protection you may use any product intended for use on a traditional tent. Please keep in mind these
screen tents are not intended to be permanent structures and it’s best to take them down when not in use.
Please be advised that applying additional products to the shelter may alter the fire retardant properties.
Q: Would it be best to completely dry my screen tent before storing if it gets wet?
A: It is recommended to dry your tent completely before storing. If not dried completely, moisture may cause
damage to the tent.
Q: How do I wash my screen tent?
A: We recommend using a gentle laundry soap that has been diluted with warm water and use a wash cloth to
spot clean any spots that need it. If needed, you can use a bleach and water solution (10 parts water to 1 part
bleach) to get rid of any mildew smell.
Q: Can I order replacement parts and accessories from your website?
A: Yes! If you would like to order replacement parts visit our website, www.QuickSetShelters.com.
For additional questions, comments or concerns please contact Clam Customer service at 763-231-4120 or email
[e-mail].
Due to Clam’s continued product development, Clam reserves the right to change specifications without notice. For
complete details, see the assembly and/or operating instructions that are provided and packaged with the purchased
product.
FREQUENTLY ASKED QUESTIONS