Cable Electronics CE Labs AV501 HDX User manual

WARRANTY
Cable Electronics, Inc. warrants this product to be free from defects in material and
workmanship, under normal use and service, for a period of one year from the
purchase by the original purchaser. If this product is defective or malfunctions,
Cable Electronics will replace or repair this unit (at their option) within a reasonable
time. No expressed or implied warranty is made for any defects caused by
immersion or exposure to liquids, abuse, neglect, improper operation of unit, excess
wear and tear and defects resulting from unauthorized disassembly and or
modification.
Cable Electronics, Inc. http://www.celabs.net
3209 Wood Street
Garland, Texas 75041
[phone] Fax [phone]
Document: AV501HDX_INFO_A.cdr Rev. A
CE labs can support many areas of your audio and
video distribution needs.
We manufacture RF modulators, RF amplifiers, HD
distribution amplifiers, and cables of all types.
See our full product line at www.celabs.net.
INSTRUCTION MANUAL
AV501 HDX
Component Video/Audio
HDTV Distribution Amplifier
With Digital Audio and composite video
True One-to-One Signal Ratio
Distributes a Video/Audio Source to multiple locations
without any signal loss.
Designed for large display arrays.
Heavy duty metal housing. Commercial duty rated.
Cable Electronics, Inc.
3209 Wood Street
Garland, Texas 75041
[phone] Fax [phone]

IN OUT IN OUT
Installation / Operation Instructions
Unpack the amplifier and power supply from the box. Place the
amplifier in a dry location, usually behind the shelf where the monitors
are located.
The unit has integrated mounting brackets that are pre-drilled in case
the user wishes to screw the unit to the shelf ( ).
Connect the source device outputs to the appropriate input jacks on the
AV501HDX. Connect cabling from the AV501HDX outputs to the
desired display or recording device. The loop output may be used as
normal or connect to the next distribution amplifier to create more
outputs.
Insert the power supply connector into the power jack of the
AV501HDX. Plug the wall transformer into a 120Vac outlet. The power
LED should be on and the unit is ready to use.
screws supplied by user
Monitor 1 Monitor 2
Source
HD DVD, SAT. RECEIVER, etc.
VIDEO
AUDIO
Monitor 3
AV501 HD
SPECIFICATIONS
X
The AV501HDX has one set of inputs and five sets of outputs (Output #5 is
designated as the loop output, but may be used to drive a monitor directly).
The unit allows any Audio/Video source, with Y, Cb, Cr, or Y, Pb, Pr Outputs
(component), to distribute Audio and Video to five different locations without
any signal loss. The amplifier also supports composite video and digital audio.
Nominal Input level: 1 Volt peak to peak
Gain: 1 Volt into 75 ohms
Input Impedance: 75 ohms
Output Impedance: 75 ohms
Isolation port to port: 32 dB
Isolation output to input: 60 dB
Return loss: >18 dB
Video bandwidth: 150 MHz
Nominal Input level: 1 Volt peak to peak
Gain: Unity (one to one)
Input impedance: 22k ohm
Output impedance: 1k ohm
THD: <0.05%
Frequency Response: 20Hz to 100kHz
Channel Separation: >75dB
Port to Port Isolation: 60dB
Out to Input Isolation: 60dB
Signal to Noise: >100dB@2Voltsout
Supports Standard SPDIF digital audio.
Unity gain when terminated into 75 ohms (2X gain, high impedance.).
Greater than 50 MHz of bandwidth to ensure minimal degradation.
: External 9 or 10 Volt AC @ 1000mA with a ( 2.1mm center
diameter) Coaxial connector. Power Supply is included.
Note: the loop output may be used to daisy chain several units together as is
typically done in store displays.
VIDEO
AUDIO
Analog:
Digital:
POWER
(All Channels including Component and Composite)
(2 Volts Unterminated)
Requirement