Cablematic RW13 User manual

Wireless 802.11g CF Card
User Manual
Version 1.0

Copyright statement
No part of this publication may be reproduced, stored in a retrieval system, or transmitted
in any form or by any means, whether electronic, mechanical, photocopying, recording, or
otherwise without the prior writing of the publisher.
Printed in Taiwan, February 2006
3

Contents
1. I ntroduction --------------------------------------------------------- 4
2. Wireless LAN Basic ---------------------------------------------------------5
3. Installation for WinCE Platform
3.1 Installation overview ----------------------------------------------6
3.2 Win CE Install Procedure ---------------------------------------7
3.3 Profile Setting----------------------------------------------------- 14
4. WinCE driver uninstall procedure ------------------------------------- 16
5. Terminologies ----------------------------------------------------------------------- 17
6. Trouble Shooting ------------------------------------------------------------------- 18
7. Appendix: Specifications ---------------------------------------------------------- 20
4

1. Introduction
Thank you for purchasing your Wireless LAN, Wireless 802.11g CF Card Adapter. This
manual will assist you with the installation procedure.
The package you have received should contain the following items:
… 802.11g Compact Flach card
… User Quick Installation Guide
… CD Containing Wireless LAN Management driver
Note: if anything is missing, please contact your vendor.
The CD contains drivers that are used for managing the Wireless LAN Card and establishing
the wireless connection with your Local Area Network.
Note : This Manual is only valid for 802.11b/g wireless CF Card.
5

2. Wireless LAN Basics
Wireless LAN (Local Area Networks) systems offer a great number of advantages over
a traditional, wired LAN system. Wireless LANs (WLANs) are more flexible, easier to
setup and manage and often more cost effective than their wired equivalence.
Using radio frequency (RF) technology, WLANs transmit and receive data over the air,
minimizing the need for wired connections. Thus, WLANs combine data connectivity with
user mobility, and, through simplified configuration, enable movable LANs.
With wireless LANs, users can access shared information without looking for a place to
plug in and network managers can set up or augment networks without installing or
moving wires. Wireless LANs offer the following productivity, convenience and cost
advantages over traditional wired networks:
… Mobility – Wireless LAN systems can provide LAN users with access to real-
time information anywhere in their organization. This mobility
supports productivity and service opportunities not possible with wired
networks.
… Installation Speed and Simplicity – Installing a wireless LAN system can be
fast and easy and can eliminate the need to pull cable through walls
and ceilings.
… Installation Flexibility – Wireless Technology allows the network to go where
wires cannot go.
… Reduced Cost-Of-Ownership – While the initial investment
required for wireless LAN hardware might be higher than the cost of wired
LAN hardware, overall installation expenses and life-cycle costs will be
significantly lower. Long-term cost benefits are greatest in
dynamic environment requiring frequent moves, adds, and changes.
… Scalability – Wireless LAN systems can be configured in a
variety of topologies to meet the needs of specific
applications and installations. Configurations are easily changed
and range from peer-to-peer to full infrastructure networks, also
allow roaming over a broad area.
6

3. Installation for Windows CE platforms
The following section will assist you to in installing wireless 802.11g CF CardAdapter
successfully. You will first install software (Utility) and then insert / attach the Wireless
LAN CF Adapter to your PDA system, and finally set the network properties to select
the type of wireless network that you wish to install. The Wireless LAN card can easily be
installed and used, without bothering to connect cables for keeping your computer to use
network resources.
3.1. Installation Overview
Here are some steps you will perform in establishing your wireless network connection:
—Please ensure the device is within the reach of WIFI signal in order to connect to
network.
—Install the software using the Install CD.
—Install the Wireless LAN CF Card (WIRELESS LAN 54Mbps Adapter).
—Configure the Network IP and SSID with encryption keys.
7

3.2. Win CE Install Procedure
Please note that the current driver for 802.11g CF card under WinCE 4.2 and
WinCE5.0 can only supports XScale and Intel Boulverde PXA 270 processor.
. Note: Be sure that your PC or Notebook has installed software such as Active Sync for
transmit data to PDA / handhold PC.
We assume that you have installed Windows CE services on your desktop PC and that you
have connected the PC to PDA or handheld PC with USB/Serial connection.
Note: The CF card shall not be plugged into PDA handheld PC if not stated.
1) Run the Microsoft Active Sync, to synchronise PDA with Computer.
8

2) Copy the CE4.2_5.0.v1.0.0_27.p3.cab to PDA
3) Run CE4.2_5.0.v1.0.0_27.p3.cab from PDA
9

If your PDA/Handheld were using WinCE4.2 or newer WinCE OS or other than English OS,
at end of installation it might show that “The device have being installed cannot be properly
displayed due to it design only for previous version of Windows Mobile Software.
4) Plug-in the Wireless LAN CF/PC card into the card slot of your PDA/handhold PC
.
5) Go to the Start menu, select Settings subfolder. Then select Connections tab from the
bottom of the page.
10

6) In the Setting page, tap on Wi-Fi Icon. This step will open Network Connections dialog
7) Choose Marvell CF8385PN Wireless Card, will enable you to configure the IP address
and DNS server for Wireless CF Card.
11

8.) If your network supports DHCP server, select the first button. Otherwise enter static IP
in the field. If you are not sure about the values of these fields, ask your Internet Service
Provider for detail.
12

9) Once have finish configuration for IP address, click on OK. It will ask you to pull out
the Wireless CF card and re-insert it back to allow the change to take place.
13

3.3 Profile Setting
1) Open the Wireless tab, this will allow you to configure the wireless connection.
Click on Add New to add your wireless connection, or choose any of the available connection being
detected.
Note: If you wishes to use other profile after setting, just simple held the point on that
SSID of network and choose connect.
2) After click on add new, please click on the General Tab on the bottom left. In this page please
input your SSID for the AP or Router into the Network Name column.
14

3) In order to set the security key, please go to Network Key tab. There was OPEN, SHARE, WPA,
WPA-PASK security option can be chooses from.
Note: If you were using OPEN or SHARE security function, that 128bits WEP key can be
entered in the WEP key column without any additional changes.
4) If there is need to use 802.1x security function, please click on the 802.1x tab and select
EAP types. There is LEAP, PEAP, TTLS and Smart Card or Certificate available.
15

4. WinCE driver uninstall procedure
Tap on the Start Menu; select Settings tab. Tap on System tab from the bottom of the
page, Tap on the on the Remove Programs. Select Marvell CF8385PN Driver and tap
on the Remove button, it will start uninstall the 802.11g CF card driver from your
PDA/Handheld PC.
16

5. Terminologies
— Network Type
Infrastructure Mode – The Driver will scan all available channels continuously until it find
one or more Access Point that matches its SSID.
Ad Hoc Mode – The driver will scan for 5 seconds looking for an existing Ad Hoc Network using the
same SSID.
— Current Channel and Transmit Rate
Shows the channel of the radio and transmit rate are being currently used for an active
connection. This value has no meaning when the radio is “Scanning”
— Signal Strength
The Signal Strength bar graph is only active when the node is in Infrastructure Mode. The
bar graph display normalized signal strength as reported by the radio.
— Encryption (WEP)
You may desire an additional measure of security on your wireless network, which can be
achieved by using WEP (Wired Equivalent Privacy) encryption. When an encrypted frame
is received it will only be accepted if it decrypts correctly. This will only happen if the
receiver has the WEP Key used by the transmitter.
17

6. Trouble Shooting
If you encounter any problems during the installation, or to confirm that the 802.11g CF card
device is installed properly, please read the following troubleshooting section.
1. Please ensure that your WinCE OS were ver.4.2 or higher.
2. Please Ensure that your PDA/Handheld device are using X-Scale and Intel Boulverde
PXA 275 processor supports.
3. Ensure that security setting is corresponds to your Security settings, which have set in
your AP or Router side.
4. If your PDA/handheld device has built in 802.11g WiFi, please ensure that built-in WiFi
are being disabled first.
5. Ensure that PDA/Handheld require Static IP address or using DHCP to assign IP from
Router/AP to your PDA/Handheld device.
6. Check is that correct Network Profile is selected.
18

The equipment has been tested and found to comply with FCC and CE Rules.Operation is subject to the
following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received including interference that may cause
undesired operation.
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired
operation.
FCC Caution: Any changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate this equipment.
IMPORTANT NOTE:
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance
20cm between the radiator & your body.
This transmitter must not be co-located or operating in conjunction with any other antenna
or transmitter.
The 802.11g CF card (FCC ID: RYK-WCFM100) is limited in CH1~CH11 for 2.4
GHz by specified firmware controlled in U.S.A.
20

Appendix: Specifications
Interface Compact Flash
LED Indicator Power, Link
Antenna Internal diversity antenna
Manufacture Pb-free, RoHS compliant
Radio Characteristics
Standard IEEE 802.11b/g
Frequency Bands
802.11b/g : ISM-Band 2.412~ 2.4835GHz
802.11g: OFDM
Modulation Tech 802.11b: CCK, DQPSK; DBPSK
Media Access Protocol CSMA/CA with ACK
Receive Sensitivity 802.11g: 54 Mbps 10-5 BER @ -73dBm;
Power consumption TX: 480mA
Rx : 270mA
Idel: 1.2mA
Software Features
Security
64bit/128bit WEP Encryption
WPA with TKIP
WPA-PSK with TKIP
802.1x
OS Support Windows CE4.2/5.0 Linux
Environmental Specifications
Dimension 56x42x5mm (LxWxH)
Weight 10g
Temperature 0 ﾟC~60 ﾟC(operating), -40 ﾟC ~ 85 ﾟC(storage)
Humidity Max 95% (Non condensing)
12.5 dBm +/- 1 dBm 802.11g
Output Power
14 dBm +/- 1 dBm 802.11b
SYSTEM REQUIREMENT
TI OMAP 1510
CPU Support Intel Boulverde PXA270 and XScale
CERTIFICATION
FCC, CE
Note: Specifications are subject to change without notice
21