CableWorld CW-4000 Series User manual

CW-4000
USER'S GUIDE
Dear User!
In spite of the rapid spreading of digital television
technology input signals for earlier analogue TV
modulators and monitors will still be needed in the next few
years. The models of Cable orld’s Multistandard MPEG
decoder series comprise one or two independent
MPEG/H.264 decoders. All the versions are equipped with
ASI and IP inputs but the C -4673 and the C -4674
models allow receiving scrambled channels, too.
The Multistandard MPEG decoders have user friendly
web interfaces, which serves the demands of both less and
highly skilled users.
The separated management port allows programming
and control of the device in a network separate from the
trunk lines.
1. MECHANICAL CONSTRUCTION
The DVB-S2 Satellite Receiver and DVB-T OFDM
Receiver is built in standard 19" x 1 H instrument
frame. It is delivered along with the following
accessories:
1. Power cord 1 ea.
2. Spare fuse T 1.25 A
(placed in the fuse holder mounting) 1 ea.
3. Crossover cable with RJ45 connectors 1 ea.
4. Cover cap for the optical receptacle 1 ea.
The power consumption of the device is very low, needs
no special cooling or ventilation.
2. ELECTRICAL CONSTRUCTION
The device is equipped with own switching mode
power supply. The supply voltage of the interface
circuitry is +3.3 V, but the signal processing circuitry
works with supply voltages of +1.2, 1.8 or +2.5 V. The
real power consumption of these devices is low, they
are suitable for continuous operation, however the
heat resulting from the few 10 watts of power
consumption must be dissipated. In most cases the
natural cooling is enough.
The device circuitry comprises high complexity
circuits, which should be configured to the given task
by the user.
3. PUTTING THE DEVICES IN OPERATION
After unpacking remove the protection foil from the
stainless steel cover of the device. Connect the device
to the specified mains voltage and switch on the power
switch. After a few seconds the device is ready to
operation.
Programming the device and saving the settings is
required only when putting the device in operation first
or when modifying the settings.
The device has a web user interface and can be
set and programmed via the Management Port.
The default IP address of the Management Port is
192.168.10.10. After building up the communication
with the device, it can be programmed to the desired
value via this input. Pressing the Reset switch sets the
Management Port IP address to 10.123.13.101.
sing the web interface requires a web browser.
Our software is tested only in Firefox browser. In other
browsers the surface may vary in appearance, proper
operation is not guaranteed. For some special tasks
the browser's performance is not enough, so we
integrated Java Applet. Running the Java program
part requires a newer version of Java installed in
advance.
To display the user interface connect your PC to
the Management Port. se a crossover cable for direct
connection and straight cable via switch. On starting
the web browser enter the Management Port IP
address in the window of the browser. The user
interface will appear on the monitor screen in a few
seconds.
The short and concise help available via the user
interface supports setting up the device. From our
website ( www.cableworld.hu) we want to help our
users' work with more information, professional
articles, software, etc.
13/14
MULTISTANDARD MPEG DECODER
CW-4671, CW-4672, CW-4673, CW-4674

DVB-S2 SATELLITE RECEIVER DVB-T OFDM RECEIVER
The Web Interface allows to build the device into a
system, where the devices are controlled via network
separated from the TS. The Management Port is
physically and logically independent from the TS
connectors of our devices.
The main characteristics of the device (type
number, serial number, IP Address, Repetition Time,
etc.) are stored in the device's EEPROM. They are in
the Device Settings menu at any time to read.
Operating experience has shown that most of the
systems need to be amended after a shorter or longer
period of time. To ensure that the changes can be
easily implemented and, if necessary, return to the
previous state, it is recommended to backup the
settings (backup file).
5. TECHNICAL DATA
The devices are specified in brochures that can be
downloaded from our website.
6. SUPPLEMENT
CableWorld appreciate if the users are going to
integrate our products into their systems and
undertake writing own software for operating these
products. CableWorld assure extra technical support
for the creative users. In the CableWorld's system the
instruction sets are available for everyone, and major
users can have the source codes of the software, too.
Besides the web user interface, the new generation
interface allows remote control with DP packets, but
this software is not yet prepared.
Besides the standard products we undertake to
supply specific needs and realize unique ideas.
We appreciate receiving all remarks, experiences,
measurement results with our products and we pay
respect to them in our further developments.
Our address: [email protected].
Type of device :
Multi tandard MPEG Decoder
CW-4671 Multistandard MPEG Decoder
(FTA, single version)
CW-4672 Multistandard MPEG Decoder Duo
(FTA, duo version)
CW-4673 Multistandard MPEG Decoder
(CI, single version)
CW-4674 Multistandard MPEG Decoder
(CI, duo version)