Calimar Cali Fun Pool User manual
To purchase replacement parts, accessories, or to obtain technical
assistance please visit us at:
www.calimarpool.com
Or email
IMPORTANT
Read this guide and follow all instructions carefully before assembling or using
this product.
Rev 1/23
Warnings………………………………………………...
Before You Begin………………………………………...
Parts List and Specications…………………………….
Preparing the Ground…………………………………...
Pool Assembly / Liner Layout………….……………….
Pool Assembly / Frame Layout………..………………..
Pool Assembly / Completion…………………………....
Pool Assembly / Fittings ……………………………….
Pump and Filter Assembly……………………………...
Disassembly…………………………...………………...
Warranty……………………………….............................
Congratulations on the purchase of your new pool! Please read this owner’s manual before
beginning assembly. e information contained within this booklet will help ease the installation
process and extend the life of your pool. We suggest using 2-3 people during the assembly of your
pool, and don’t forget to save this manual for future reference!
Getting started:
Pg. 3
Pg. 4
Pg. 5
Pg. 6
Pg. 7
Pg. 8
Pg. 9
Pg. 9
Pg. 10
Pg. 11-12
Index
2
Important - Please Read
Do not install your pool under electrical lines.
Always use a GFCI outdoor protected receptacle to plug your pool equipment into.
Always make sure that the pool area is supervised by a competent adult at all times.
Do not allow any diving, jumping or headrst entry into the pool.
Never swim alone.
Never use the pool under the inuence of alcohol or drugs.
Never allow children to use the pool unsupervised.
Never leave your pool assembled without water.
Never assemble the pool when the ground is o level.
Never assemble the pool on so or unstable ground.
Never try to make one end deeper on the pool oor as the liner does not stretch.
Do not over ll the pool.
Never allow the pool to go unltered for a time period longer than 24 hours.
Do not attempt assembly on any day with winds in excess of 20 MPH.
Never assemble your pool on nut grass.
Never assemble the pool without proper concrete or pressure treated support bases as shown in
this assembly guide.
Never drag the pool liner. Always be sure to pick up the liner and carry it.
Always remember that safety is the key to fun in your new pool.
Warning
WARNING:
Never jump or dive into pool.
Horseplay of any kind in pool may result
in spinal or fatal injury.
Adult supervision is required at all times.
3
4
Before You Begin
PLEASE NOTE:
It is normal for the pool to show some deflection of the top rails inward while the pool is filling. Once
the pool has filled completely, the deflection of the top rail may be slightly outward. This is common
and will not effect the structural integrity of your pool.
In some rare cases, due to different climate conditions and local water quality, your new pool may
“sweat” or “weep” slightly after being filled for the first time. This may appear around the bottom
perimeter of your pool, most often noticeable when installed on cement. This “sweating” or
“weeping” will most often stop once the outside air temperature and inside water temperature
equalize in a few weeks time or less. This is similar to condensation which occurs on the outside of
a can of cold soda on a hot day. If after several weeks, your pool continues to “sweat” or “weep”,
please contact your dealer or CaliMar Pool directly for further assistance.
In some rare cases, due to the advanced design of the PVC poly-fabric reinforced heavy duty liner,
small microscopic pinholes may occur in the material due to the curing process when manufactured.
These microscopic pinholes may appear as a small “weep” in the material which can be easily
omitted by dabbing a small amount of transparent glue which is provided with your pool. Once
applied, wipe off with a dry cloth. The “weep” will immediately stop and the transparent glue will be
invisible. If you do not wish to apply a small amount of transparent glue, you may simply wait a few
weeks as most often the “weep” will stop on it’s own. This is in no way a defect which will affect or
compromise the integrity of your new pool.
To find the serial number of your pool, go to the side of the pool where your equipment hoses attach
to the pool. On the foot strap to the right you will see your serial number CF-#-####. The last four
numbers is your serial number, and you will need this number to properly register your product with-
in 20 days from purchase.
5
Parts List & Specications
A. Pool Size / Space Required
It is recommended to allow an additional 18” of space around the perimeter of your portable pool. For example: a 10’ x
18’ rectangle pool should have an area of 13’ x 21’. e larger dimension (13’ x 21’) is referred to as the “foot print”.
B. How do I nd level?
It is important that your pool be placed on level ground. ough your pool can tolerate being slightly out of level, it is
best for proper ltration, as well as visual concern, to have your pool as level as possible. Here is a simple way to how
to nd level ground:
You will need:
Two small wooden stakes
Length of string, two feet longer than the longest dimension of the pool
One “line level” (can be purchased from any hardware store)
1. Set one stake into the ground at one end of where the pool will be and the other stake at the other end.
2. Tie the string stretched between both stakes; make sure it is stretched tight.
3. Now set the line level in approximately the center of the string.
4. Tap either stake further into the ground to level the string at both ends.
5. Now measure the distance from the ground to the string at both ends. If one measurement is 5” at one stake, and
7” at the other stake, then you are only 2” o level.
C. Surface preparation:
If there is grass in the pool area, we recommend removing grass and any foliage prior to assembling of the pool. In
addition to removing grass, it is recommended to add 2 to 3 inches of washed plaster sand or Happy Bottom® pad for
additional protection of the pool liner prior to assembly. (Happy Bottom® can be purchased from your local swimming
pool dealer).
D. Base support:
We always recommend supporting the vertical uprights with concrete or a pressure treated wood base. Failure to use
support base may result in structural failure which is not covered by the warranty.
Preparing the Ground
6
7
Pool Assembly / Liner Layout
Step 1:
Locate the area most suited for setting up the pool. Clear it of any sharp objects or debris and level it to zero as ex-
plained on the “Preparing the Ground” page. If the pool is assembled on unleveled ground, it may suer permanent
structural warping or damage the liner.
Step 2:
Remove the liner from the box marked “Liner” and place it at the center of the area where you plan to assemble the
pool. Take care not to damage the liner when opening the box. DO NOT USE SHARP OBJECTS TO OPEN THE
BOX THAT CONTAINS THE LINER.
Step 3:
Unfold the liner. Locate the place where the pump and lter system will be connected and position the 2 circular open-
ings on the side where you intend on placing the pump and lter.
Step 4:
Remove the frame (Parts A & B) from the box marked “Frame”. At this point you will not need any “U-Tubes” (Part
C). Lay all of the upper frame out in the order indicated below. (Locate each frame piece corresponding with the parts
list on page 5.)
''
8
Pool Assembly / Frame Layout
Step 5
Assembling the long sides rst, starting from the side at your right, INSERT INTO THE RECTANGULAR BIG
OPENING CORNER OF THE POOL, THE “A” TOP RAIL WITH THE FEMALE END LOOKING AHEAD.
Make sure to start from the right lateral side. is will allow the corners to t correctly. Insert the rest of the pipes one
at a time, in order of the diagram on the previous page and make sure they are locked correctly. You will hear a “click”
when they are properly positioned. Make sure all holes in the pipes coincide with the openings on the sleeve of the
liner. Repeat this operation with the opposite long lateral.
Step 6
Assembling the short sides, take a long lateral top rail and extend it outwards, (two people would be best). Repeat with
the opposite long lateral top rail. As you did in Step 5, insert the top rails into the sleeve, STARTING FROM THE
RIGHT AND WITH THE FEMALE END LOOKING AHEAD. Insert one pipe at a time in order to the diagram on
the previous page making sure you hear a “click”. Repeat this operation with the opposite short lateral.
Step 7
To nish with the assembly of the top rail, insert the corner pipe with the male end into the female end of the top rail.
IMPORTANT TIP: Make sure to nish top rail assembly by inserting the last corner piece, female end last. is
step is very important as the corner piece is designed with an o set. Failure to follow the instructions may result in
tearing of the material. Do no force corner piece, material will not stretch! Make sure to nish with the female
end last!
9
Step 9
Now that you’ve completed the pool assembly, it’s time to install the skimmer and return tting . Follow the diagram
below. Once the skimmer has been properly assembled, insert the two skimmer straps through the openings on the
skimmer and buckle them securely to the loops on the pool liner.
Pool Assembly / Fitting Assembly
Step 8:
Pull foot straps under liner outwards. Insert “U-Tubes” in every foot strap. Two people should li one short lateral
top rail of the pool while a third person places the top of the “U-Tube” into the corresponding holes in the underside
of the top rail. e pool will remain standing, which will make it easier to t the rest of the “U-Tubes” into the top rail.
Special note: Once you nish, make sure the liner ts comfortably on the structure. Go around the pool to check
that the framework is assembled correctly. Make sure each “U-Tube” is correctly inserted into each hole on the top
rail. Go around the perimeter of the pool and tug on the bottom of the “U-Tube” outward. Repeat this process 2-5
times as it will help to set the frame system and level the pool prior to lling with water. Once you start lling the pool
with water, you will not be able to make any changes.
MAKE SURE EACH “U-TUBE” IS FULLY INSERTED INTO TO TOP RAIL PRIOR TO
ADDING WATER.
IMPORTANT: Make sure to place a support base on concrete or treated wood under each vertical upright as
correctly shown below.
Step 10:
With the skimmer and return ttings now in place, assemble the pump and lter package and connect the hoses ac-
cording to the diagram below. (Equipment may vary by dealer)
Step 11:
Before you start lling the pool with water, assemble and secure the ladder with the ladder straps included. Refer to
the ladder instructions for assembly procedures.
Enjoy:
You have now completed the installation process and are ready to start enjoying the benets of pool ownership. Be
sure to retain this manual for future reference.
Disassembling the pool
Step 1
Drain the pool completely and dry all moisture o of the liner. is will prevent mildew or algae growth while in stor-
age.
Step 2
Remove all top rails, corner pieces, “U-Tubes” and store.
Step 3
Make sure that all of your pool items are stored in a cool dry place without sun exposure.
Equipment Assembly / Pool Disassembly
10
CALIMAR POOL
www.calimarpool.com
Five Year - Cali Fun Pool
Pro - Rated Limited Warranty
This warranty covers the pool only supplied by CaliMar Pool, which includes the metal super-structure and the
polyester reinforced membrane water container structure. Excluded from this warranty are the ladders, pumps and
electric motors, which are warranted by their manufacturer. To validate this limited warranty, the pools must be
registered with CaliMar Pool. Please provide all the information requested on the warranty registration form and
email with 20 days of purchase.
WARNING:
Never jump or dive into the pool.
Horseplay of any kind in the pool
may result in spinal or fatal injury.
Adult supervision is required at all times.
To obtain performance under this warranty, first contact the dealer from whom the product was purchased. The dealer
is charged with the responsibility of determining, beyond a reasonable doubt, that the defect was once created by the
manufacturer. The dealer may correct the defect or arrange to send the damaged / defective component back to
CaliMar Pool for repair (freight prepaid by pool owner).
Cali Fun Pool are designed for your swimming enjoyment. Entry and exit from your pool should only be by a proper
above ground swimming pool ladder. DO NOT DIVE OR JUMP!
This card must be email within 20 days of your purchase - [email protected]
FIVE YEAR LIMITED WARRANTY REGISTRATION CERTIFICATE
CALIMAR POOL
www.calimarpool.com
1. This warranty is extended to the original purchaser (consumer) only and is non-transferable.
2. This limited warranty covers only the pool supplied by CaliMar Pool
3. This CaliMar Pool warranty provides prorated coverage over a five (5) year period, only on the welded seams and metal frame. If any defect in
workmanship on the welded seams or metal frame is confirmed by the dealer and/or CaliMar, and is reported to the dealer and/or CaliMar, the parts
will be replaced or repaired at the applicable prorated cost. If a determination of defect cannot be confirmed by the local dealer, the purchaser may be
required to send the part(s) to CaliMar. The purchaser, at their expense, and after prior authorization from CaliMar, should clean, package and send
the part(s) to CaliMar. If, at the sole discretion of CaliMar, there is determined to be a manufacturing defect, the part(s) will be replaced or repaired, at
CaliMar's option, and the applicable return freight may be reimbursed. Any part(s) found defective in the first year from the date of purchase will be
repaired or replaced free of charge. For the next four (4) years, part(s) found to have a manufacturing defect will be replaced at the then existing
manufacturer's suggested retail price prorated by applying the percentage listed below for the appropriate year. During the five(5) year period, the
purchaser is responsible for paying the below indicated percentage of the then current list prices of the warranty covered item:
Freight for the new or repaired part(s) will be billed collect. A cashier's check or money order covering the cost of the new or repaired parts(s) will be
required prior to the shipment from CaliMar.
2nd Year: 50% 3rd Year: 75% 4th Year: 80% 5th Year: 90%
4. Failure or refusal of the purchaser to allow dealer and/or CaliMar to inspect the product claimed defective (at dealer's and/or CaliMar business
location) shall render this warranty null and void. CaliMar cannot be responsible for damage to the part(s) caused by the purchaser or installer.
5. This warranty is null and void if the design of this product is altered in any way. The pool must be assembled according to the factory instructions
with no alterations to any parts. The pool is designed to be installed as an above ground portable pool. Burying the pool below the surface of the ground
voids this warranty.
6. CaliMar assumes no responsibility for errors in installation by the purchaser or by a hired installer. If the pool is installed by someone other than the
purchaser, it is purchaser's responsability to supervise the installation to be sure that the CaliMar installation are followed.
7. Accidental, consequential or other damages will not be paid by CaliMar, including but not limited to, the COST OF LABOR AND/ OR WATER OR
CHEMICAL LOSS OR ANY DAMAGES THAT MAY OCCUR THEREFROM.
8. Pool must not be installed over nut grass
9. A pool left standing empty is exposed to potential severe damage. Such damage is not covered by this warranty. If the pool is emptied, it should
be disassembled and properly stored immediately.
10. Damage to the liner or frame from ice if not winterized properly is not covered by this warranty.
11. Pool must be assembled on level ground or level surface. Support for vertical uprights must be placed on ground in accordance with assembly
instructions. If not, this warranty is null and void.
12. All objects (rocks, sticks, etc.) must be cleared from the area the pool is to be installed on.
13. CaliMar is not responsible for damage to the pool due to improper use of chemicals, lack of maintenance or improper use of chlorine tablets.
Caution should be used with tri-chlor tablets as direct contact can damage the pools liner
14. Warranty Exclusions: Misuse of chemicals which cause fading, staining, shrinking, wrinkling, tears, rips, cuts, punctures, dry rot, sun rot,
negligence, alterations, improper installation or assembly, aesthetic tears or rips caused by any type of undue stress or during assembly/disassembly,
aesthetic blemishes or tears not compromising structure or pools ability to hold water, vandalism, civil disturbance or acts of gods such as wind blown
debris, grass growing through liner, accidental or malicious damage to liner, or a product user for commercial or institutional purposes.
15. To validate warranty, purchaser must return warranty form within 20 days from purchase.
Table of contents
