Coleman Power Steel 90387E User manual

DO NOT RETURN THIS ITEM TO THE STORE
OR WEBSITE WHERE IT WAS PURCHASED.
CONTACT US DIRECTLY WITH ANY QUESTIONS,
OR FOR DEFECTIVE OR WARRANTY CLAIMS.
CALL US DIRECTLY FOR IMMEDIATE HELP!
Toll-Free: 1-855-838-3888
Website: www.bestwaycorp.com
THIS PRODUCT IS COMPLIANT TO ANSI/ APSP 4 AMERICAN NATIONAL STANDARD FOR
ABOVEGROUND POOLS / ONGROUND RESIDENTIAL SWIMMING POOLS & INTERNATIONAL SWIMMING
POOL & SPA CODE ( ISPSC)
#90387E
Power SteelTM Pools
Owner’s Manual
S-S-005766

3
S-S-005766
Put 1 to 2 in. of water in the pool to cover the floor. Once pool floor is slightly covered, gently
smooth out all wrinkles. Start in the center of the pool and work your way clockwise to the
outside.
WARNING
smooth out the bottom

The pool must be set up on a completely flat and level surface. Please do not install the pool if the
surface is inclined or sloped. Failure to do so may result in the product collapsing which may
cause serious injury.
No sitting or standing on the top rails.
S-S-005766
4

90º
90º
After the installation of the pool's steel frame is completed, ensure that the verticals are
perpendicular to the ground. If they aren’t, the verticals could be bent or deformed.
S-S-005766
5

Only for outdoor use.
Teach your children to swim.
Never dive, jump, or slide into the pool.
Adult supervision is always required.
Parents should learn CPR.
Never swim alone.
Keep all electrical radios, speakers and other appliances away from the swimming
pool.
When you touch the filter, pump, or electrical parts, be sure the ground under your
feet is “Bone Dry.”
All electrical outlets should have a GFCI and connections should be a minimum of
5 feet (1.52 m) from the outside perimeter of the wall of the pool. From 5–10 feet
(1.52–3.05 m), there should be either a fixed connection (outlet box) or twist lock
connection with a GFCI.
Connect power cords to a 3-wire grounding-type outlet only.
Keep all breakable objects out of the pool area.
Alcohol consumption and pool activities do not mix. Never allow anyone to swim, dive
or slide under the influence of alcohol or drugs.
Severe electrical shock could result if you install your pump or filter on a deck. The
pump or filter could fall into the water, causing severe shock or electrocution. Do not
install on a deck or other surface at, above, or slightly below the top rail of the pool.
Do not use the pool during severe weather conditions, i.e. electrical storms,
tornadoes, etc.
Be aware of overhead power lines when vacuuming your pool or using a telescoping pole.
Do not allow diving, climbing, sitting, or standing on the top rails of the pools.
Do not allow roughhousing and horseplay.
Do not engage in extended breath holding activities underwater; you may black out
and drown.
Install a pool ladder(s) or staircase for entry and exit from the pool.
Keep deck clean and clear of objects that may create a tripping hazard.
Check regularly for signs of wear or loose bolts that could make the deck unsafe.
Instruct pool users about the proper use of all pool ladder(s) and staircases.
Face ladder going up or down.
Allow only one person at a time on the ladder.
Check all nuts and bolts regularly to ensure that the ladder stays sturdy.
Remove or secure the ladder to prevent entry to pool when not in use.
Please contact pool site dealer or manufacturer for additional safety signs if deemed
necessary.
For pool service, select a certified pool professional.
Any equipment connected to the circulation systems shall be positioned so as to
prevent their being used as a means of access to the pool by young children.
The installation must comply with the codes of the authority having jurisdiction and
may require permits for building, plumbing electrical, zoning, etc.
The pool shall be located a minimum distance of 6 ft. (1.83 m) from any electrical
receptacle.
All 125 volt, 15 and 20 ampere receptacles located within 20 ft. (6.0 m) of the pool
shall be protected by a ground fault circuit interrupter (GFCI). The 20 ft. (6 m) distance
is measured via the shortest straight line distance the supply cord would follow
without piercing a floor, wall, ceiling, doorway, window, or other permanent barrier.
Prior to use of the pool, the installer shall affix all no diving signs and safety signs in
accordance with installation instructions so they can be easily visible.
A barrier is necessary to provide protection against potential drowning and near
drowning. Barriers are not a substitute for the constant supervision of children. A list of
emergency telephone numbers shall be posted, such as the nearest available police,
fire, ambulance, and/or rescue unit. These numbers are to be kept near the telephone
that is closest to the pool.
Toys, chairs, tables, or similar objects that a young child could climb shall be at least
4 feet (1219 mm) from the pool.
If deck is used by the installer, it will need to comply with APSP-8.
Basic lifesaving equipment, including one of the following, shall be on hand at all
times: a. A light, strong, rigid pole (shepherd’s crook) not less than 12 ft. (3.66 m) long.
b. A minimum ¼ in. (6 mm) diameter rope as long as 1½ times the maximum width of
the pool or 50 feet (15.24 m), whichever is less, which has been firmly attached to a
Coast Guard-approved ring buoy, or similarly approved flotation devices. The
swimming pool cover is not designated as a safety barrier.
Please use artificial lighting during nighttime pool use, to illuminate all safety signs,
ladders, steps, deck surfaces and walks.
The pool is subject to wear and deterioration. If not maintained properly, certain types
of excessive or accelerated deterioration can lead to failure of the pool structure that
might release large quantities of water that could cause bodily harm and property damage.
The bottom of the pool shall be visible at all times from the outside perimeter of the pool.
The installer of the vinyl liner shall affix on the original or replacement liner, or on the
pool structure, all safety signs in accordance with the manufacturer’s instructions.
If you have a filter pump, refer to the pump’s manual for instructions.
The ladder shall be located on a solid base and the ladder shall be installed per the
ladder’s instructions.
Publications are available that describe the risk of drowning, entrapment, and diving
accidents. Available publications related to pool safety include the Association of Pool
and Spa Professionals’ (APSP) booklets entitled: The Sensible Way to Enjoy Your
Aboveground/Onground Swimming Pool, Children Aren’t Waterproof, Pool and Spa
Emergency Procedures for Infants and Children, Layers of Protection, and the latest
published edition of ANSI/APSP-8 Model Barrier Code for Residential Swimming
Pools, Spas, and Hot Tubs.
For additional safety information, see www.APSP.org.
THIS PRODUCT IS COMPLIANT TO ANSI/ APSP 4 AMERICAN NATIONAL
STANDARD FOR ABOVEGROUND POOLS / ONGROUND RESIDENTIAL
SWIMMING POOLS & INTERNATIONAL SWIMMING POOL & SPA CODE (ISPSC)
(Only for USA & only for pools with a water depth of more than 36in.(914mm))
Please read carefully and keep for future reference.
6
POWER STEEL™ POOL
Part descriptions
NOTE: Some parts already have been installed on the pool.
Assembly usually takes approximately 20-30 minutes with 2-3 people.
WARNING
PREVENT
DROWNING
Watch children at all times.
WARNING
NO DIVING!
You can be permanently injured.
Shallow water.
Pool liner
G
Hose adaptor
H
Top Rail
A
Vertical Pool Leg
B
T-connector
C
Pin
D
Footing
E
Pin Gasket
F
Stopper
I
Drain valve cap
J
Control Valve
K
Pool inlet Strainer
L
Spring-loaded Pin
S-S-005766

CHOOSE THE CORRECT LOCATION
NOTE: The pool must be set up on a completely flat and level surface. Please
do not install the pool if the surface is inclined or sloped.
Correct conditions to set up the pool:
• The selected location has to be capable of uniformly supporting the weight for the
entire time the pool is installed; moreover the location must be flat and must be
cleared of all objects and debris including stones and twigs.
• We recommend positioning the pool away from any objects children could use to
climb into the pool.
NOTE: Position the pool near an adequate drainage system to deal with
overflow or to discharge the pool.
Incorrect conditions to set up the pool:
• On uneven ground the pool may collapse, causing serious personal injury and/or
damage to personal property and will void the warranty and prevent any service
claims.
• Sand should not be used to create a level base; the ground must be dug out if
necessary.
• Directly under overhead power lines or trees. Be sure the location does not contain
underground utility pipes, lines or cables of any kind.
• Do not set up the pool on driveways, decks, platforms, gravel or asphalt surfaces.
The selected location should be firm enough to withstand the pressure of the water;
Mud, sand, soft / loose soil or tar are not suitable.
• Grass or other vegetation under the pool will die and may cause odors and slime to
develop, therefore we recommend removing all grass from the selected pool
location.
• Avoid areas prone to aggressive plant and weed species that may grow through the
ground cloth or liner.
NOTE: Check with your local city council for by-laws relating to fencing,
barriers, lighting and safety requirements and ensure you comply with all laws.
NOTE: If have a filter pump, refer to the pump’s manual for instructions.
NOTE: The ladder must match the pool size and should be used only for
entering and exiting the pool. It is forbidden to exceed the permitted payload of the
ladder. Check regularly if the ladder is properly assembled.
Installation
1. Lay out all parts and check that you have the correct quantities as listed in the
components list. If you are missing any part do not assemble the pool. Contact
Bestway Customers Service for assistance.
2. Spread out the pool and make sure the pool is right side up. Let it sit exposed to
direct sunlight for 1 hour or more so that the pool is more flexible during set up.
3. Place the pool near an adequate drainage system to deal with overflow water and
ensure the pool’s inlet A and outlet B are correctly positioned to allow your filter
pump to connect to a power source.
NOTE:Do not use extension power cords to power your pump.
ATTENTION: Do not drag the pool on the ground, this can damage
the pool.
1in. - 2in.
2-5 cm
5
1
A
A
A
A
A
AAA
A
A
A
A
AAAA
A
C
AA
C
C
C
C
CC C C
C
C
C
C
2
3
D
F
POWER STEEL™ POOL
4
E
B
A
B
C
D
E
F
G
H
I
J
K
L
NO.
Qty
26
26
26
54
26
54
1
1
2
1
1
1
#B90387
26ft. x 52in. (7.93m x 1.32m)
Part #
P61684
P61352
P61764
P61759
P61760
P61755
90387ASS18
P6H1420
P6H1418
P6H1158
P6(H1)510
P6H1317
7
S-S-005766

ATTENTION: Do not use the pump when pool is in use.
During swimming pool season, the filtration system must be used every day. Be sure
to run it long enough to ensure the pool water is adequately filtrated and circulated
until it is clean.
Dismantling
1. Unscrew the drain valve cap on the outside of the pool counter clockwise and
remove.
2. Connect the adaptor to the hose and put the other end of the hose in the area
where you are going to drain your pool. (Check local regulations for drainage
by-laws.)
3. Screw control ring of the hose adaptor clockwise onto the drain valve. The drain
valve will be open and water will start to drain automatically.
ATTENTION: Water flow can be controlled with the control ring.
4. When draining is finished, unscrew the control ring to close the valve.
5. Disconnect the hose.
6. Screw the cap back onto the drain valve.
7. Air dry pool.
ATTENTION: Do not leave the drained pool outside.
Storage and Winterization
1. Please remove all accessories and spare parts of the pool and be sure they are
clean and dry before you store them.
2. Once pool is completely dry, sprinkle with talcum powder to prevent pool from
sticking together. Carefully fold pool.
If pool is not completely dry, mold may result and damage the pool liner.
3. Store liner and accessories in a dry place with a moderate temperature between
5ºC / 41ºF and 38ºC / 100ºF.
4. During the rainy season, pool and accessories should be stored as per above
instructions.
5. Improper draining of the pool might cause serious personal injury and/or damage to
personal property.
6. We strongly recommend the pool is disassembled and stored in a dry location out
of chlidren's reach during the off season (winter months).
Filling Pool with Water
ATTENTION: Do not leave pool unattended while filling with water.
1. Fill pool until water capacity is 90%. DO NOT OVERFILL as this could cause the
pool to collapse. In times of heavy rainfall you may need to empty some of the
water to ensure the level is correct.
2. When filling the pool is completed, check that the water is not collecting more on
any side to ensure the pool is level.
IMPORTANT: If the pool is not level, drain the water and re-level the
ground by digging it out. Never attempt to move the pool with water in it as serious
personal injury or damage to the pool may result.
WARNING: Your pool may
contain a great deal of pressure. If your
pool has a bulge or any uneven sides,
then the pool is not level. The sides may
burst and the water may discharge
suddenly causing serious personal injury
and/or damage to property.
3. Check the pool for any leaks at the valves
or seams. Check the ground cloth for any
evident water loss. Do not add chemicals
until this has been done.
NOTE: Drawings for illustration purpose only. May not reflect actual product.
Not to scale.
TEST
pH value
Cyanuric acid
Free chlorine
Chlorine compound
Algae
Calcium hardness
IDEAL VALUES
7.4 – 7.6
30 – 50 ppm
2 – 4 ppm
0
None visible
200 – 400 ppm
Pool Maintenance
If you do not adhere to the maintenance guidelines below, you and your children’s
health could be at risk.
IMPORTANT: If you don’t adhere to the ideal values of the water
chemicals, the PVC can be damaged and become discolored.
The following table lists the sequence of the tests that should be carried out to obtain
the ideal values. Regularly check the pH value and chlorine concentration weekly and
adjust as needed to reach the ideal values.
Proper Water Level
Connection Valve Assembly To keep your pool clean:
1. Contact your local pool supply shop for advice and purchase of chemicals and pH
kits. One of the most important factors to increase the life of the liner is to
continuously keep the pool water clean and healthy. Please strictly follow the
instructions from professional technicians for the water treatment through the use
of chemicals.
2. Locate a bucket of water next to pool to clean users’ feet before entering the pool.
3. Cover the pool when not in use.
4. Skim pool regularly to avoid settled dirt.
5. Check and wash the filter cartridge regularly.
6. Gently clean any scum from below the top ring with a clean cloth.
7. In case of rain water, check that the water level is not higher than the
recommended amount. If so, YOU HAVE TO DISCHARGE THE EXCESS WATER.
Proper maintenance can maximize the life of your pool.
A
B
S-S-005766
8

Repair
Check pool for any leaks from valves or seam and check the ground cloth for any
evident water loss. Do not add chemicals until this has been done.
NOTE: In the event of a leak, patch your pool using the underwater adhesive
repair patch provided.
UnderWater Adhesive Repair Patch(the size of broken ≤ 2.5cm)
NOTE: Do not need to drain the pool, repair patch can be used underwater.
30’
1. Find the broken area.
3. Carefully peel patch.
5. Wait 30 minutes before use.
4. Apply the repair patch to repaired site and smooth out any air bubbles.
Press for 30 seconds.
2. Clean the area to be repaired.
30’
5. Wait 30 minutes before use.
Tritech PVC Material Repair Patch(2.5cm ≤ the size of broken ≤ 5 cm )
NOTE: Glue is not included due to shipping constraints. You can find PVC or
silicone-based glue at most retail outlets. Carefully read the warning labels and
closely follow instructions on the back of glue before attempting the following repair
steps.
1. Discharge the water, fully clean and dry area to be repaired.
2. Cut the correct size from the Tritech PVC Material Repair Patch.
3. Apply only the amount of glue (not included) needed to cover the repair site.
4. Press the repair patch firmly to repair site for 30 seconds.
9
S-S-005766

10
The product you have purchased comes with a limited warranty provided by the manufacturer of the product, Bestway®. Bestway stands behind our quality guarantee and
assures, through a replacement warranty, your product will be free from manufacturer’s defects that result in leaks.
This warranty applies for only 90 DAYS from the sale date. WITH PROOF OF SALE, a defective pool will receive free repair or replacement at option of seller.
To file a warranty claim, please contact your Bestway After Sales Center at 1-855-838-3888 before sending any documents, and they will provide full instructions of what is
needed for your claim.
Bestway is not responsible for economic loss due to water or chemical costs, will not replace any products deemed to have been neglected or used outside of the owner’s
manual guidelines. Bestway’s warranty covers manufacturing defects discovered while unpacking the product or during use, as recommended within the user manual. This
warranty applies only to the product and must not have been modified by any 3rd parties. The product must be stored and handled in accordance with the technical
recommendations.
The warranty does not cover damages caused by misuse, abuse, neglect, including, but not limited to:collision, fire, excessive heat exposure, improper use of chemicals,
exposure to extreme weather conditions, improper installation, or improper storage.
Replacements and repairs don’t extend the duration of warranty. The date to be considered as the start of the warranty is the one shown on the original receipt/purchase
invoice.
Please choose the type of your pool:
•
L
I
M
I
T
E
D
•
•
W
A
R
R
A
N
T
Y
•
90 DAYS ON POOL
Website: www.bestwaycorp.com
Toll-Free: 1-855-838-3888
Please provide your address details in full. Note: Incomplete address details will result in delayed shipments.
Bestway reserves the right to charge for redelivery of undelivered packages where the recipient is at fault.
REQUIRED INFORMATION - PLEASE WRITE THE SHIPPING ADDRESS
Name: Address:
Zip Code:
Retailer:
City: State/Country:
Mobile:
Fax:
Telephone:
E-mail:
POOL ITEM CODE: BATCH NUMBER:
DATE:
Customer Code Number:
TO: Bestway Service Department Date of purchase receipt:
Bestway reserves the right to request photographic evidence of defective parts, or to require sending the item for additional testing.
In order to better assist you, we request all information you provide to be complete.
IMPORTANT: ONLY THE DAMAGED PART WILL BE REPLACED, NOT THE COMPLETE SET.
FOR FAQ, MANUALS, VIDEOS OR SPARE PARTS, PLEASE VISIT OUR WEBSITE: www.bestwaycorp.com
Problem Description
Item is torn/ Leaking
Missing part (Please use the code for the missing part. This can be found in the owner's manual.)
Other (Please describe)
Faulty welding Faulty drain valve
22’X52”
#BXXXXX
BWSHFXXXXXX
YYYY-MM-DD Batch Number
Item Code
S-S-005766

© 2015 The Coleman Company, Inc.
and are registered trademarks of The Coleman Company, Inc., used under license.
Manufactured by
©2015 Bestway (USA) Inc., 3411 E. Harbour Drive, Phoenix, Arizona 85034, United States of America
®™ Trademarks used in some countries under license to
Bestway Inflatables & Material Corp., No.3065 Cao An Road, Shanghai, 201812, China
www.bestwaycorp.com
S-S-005766