CALRAD Electronics 40-1090-3D-IR User manual

Electronics
For technical assistance call: 323-465-2131
CALRAD
R
www.calrad.com
Plasma, LCD-
Monitor, DLP Projector
L.E.D.,
Single Cat5e or Cat6 Cable
RJ45
Output
RJ45
Input
5Vdc Power Supply
5Vdc Power Supply
40-IRC Interface Cable Included
Satellite, Bluray, STB, Media PC
92-152
IR Emitter
40-1090-3D-IR Transmitter
40-1090-3D-IR Receiver
IR Remote
Control
IR
Receiver
Power
Power
IR
Receiver
IR
Emitter
HDMI
Output
HDMI
Input
Please Note!
Some distances may vary and are dependent on
manufactures individual HDMI specifications. All
products should be fully tested prior to committing
to a UTP Cat5e, Cat6 solution and sealing long
runs of cables inside walls, possibly compromising
your installation.
• HDTV Resolutions:
Cat5e 62M (200 ft. max) 480i/p, 720p, 1080i
• CAT5e 33M (110 ft. max) up to1080P,
CAT6 43M (140 ft. max)@1080p @ 24/50/60Hz
• IR Carrier Frequency: 30kHz - 60kHz
• IR Cable Input/Output interface:
1 x 3.5mm Mono Jack, (IR Emitter)
• Connectors: HDMI ln/Out Connectors, 19 pin
Female Jack, 1 x RJ45 Shielded Jack each unit.
• DC Power Supply: 2 x 5V, 1Amp Regulated
• Weight: Transmitter: 150g/ Receiver: 140g
• Transmitter: L-2.64” x W-4.0” x H-1.1”
• Receiver: L-4.0” x W-2.6” x H-1.1”
92-179 Interface cable for connecting
directly to the 92-160 or 92-165 IR block
The receiver can be
powered by the
transmitter over the
Cat5e/Cat6 cable up
to 50ft. from the
transmitter. Use the
5Vdc power supply
over 50ft. distances.
Brochure & Typical Application Sheet
40-1090-3D-IR-6122015-WB
Copyright CALRAD ELECTRONICS 2015All specifications subject to change without notice
Electronics
For technical assistance call: 323-465-2131
HDMI Plus IR
Over UTP Cat 5e/6
Extender\Transmitter
Tx
R
CALRAD
1080p - 3D Signal
40-1090-3D-IR
Part No.
Electronics
For technical assistance call: 323-465-2131
HDMI Plus IR
Over UTP Cat 5e/6
Extender\Receiver
Rx
R
CALRAD
1080p - 3D Signal
40-1090-3D-IR
Part No.
40-1090-3D-IR
HDMI- IR BALUN OVER
SINGLE CAT5e/6 CABLE
Receiver
Transmitter
Sold in Pairs
FCC, UL Approved Devices
Please Note! We recommend Cat6
cable for reliable 3D signal delivery.
CABLE DISTANCE:
CAT5e: 480i, 720p, 1080i - 125 ft.
CAT6: 1080p - 148 ft.
POE
50 FT.
OR LESS
From Start to Finish
Connector
Wiring Diagram
568B
HDMI Cable
6 ft. max length
HDMI Cable
6 ft. max length
5Vdc Power Supply
HDMI
Input
3
D
CompliantD
3
The 40-1090-3D-IR balun provides a single UTP category 5e/6
cable solution to deliver pristine digital signals from all HDTV
formats and signal sources from 480i/p to1080i/p. Balun
technologies are perfect solutions for replacing HDMI & IR cables
that are limited to shorter distances and difficult to route thru walls
and cabinets. Balun technology also offers many advantages when
HDTV video technology changes by installing new updated baluns
with the latest technology.
Note!: Set IR Switch to RX
Note!: Set IR Switch to TX

Electronics
CALRAD
R
www.calrad.com
Part No: 40-1090-3D-IR
Transmitter Receiver
++
++
++
++
HDMI & IR Cat 5e/6 Extender HDMI & IR Cat 5e/6 Extender
DC5V DC5V
ON ON
HDMI Input HDMI Output
IR IR
TXRX
RJ45 Signal Output RJ45 Signal Input
Setting
Setting
IR IR
IR
TXTX
TX
RXRX
RX
1
1
2
2
ON
ON
+-+-
RJ45 Jack
(UTP) Signal
RJ45 Jack
(UTP) Signal
DC
Power
DC
Power
HDM
Input
HDM
Output
IR
In/Out
IR
In/Out
Function
L.E.D.
Function
L.E.D.
EDID
Setup
IR
Tx, Rx
Switch
IR
Tx, Rx
Switch
Use and store external EDID codes into the transmitter
Move DIP switch 1 to off
Move DIP switch 2 to off will select the first default EDID: supports 1080i / LPCM 2 channel. Power up the transmitter.
Move DIP switch 2 to on will select the second default EDID: support 1080P / LPCM 5.1 channel. Power up the transmitter.
Move DIP switch 1 to on unplug the DC power supply to the transmitter.
Connect the HDMI from the 40-1090-3D-IR to the TV display for auto backup of the TV EDID code.
Move DIP switch 2 to off selects the first default EDID: supports 1080i / LPCM 2 channel.
Move DIP switch 2 to on selects the second default EDID: support 1080P / LPCM 5.1 channel.
Connect the DC power supply to the transmitter when the EDID learning process is complete the function L.E.D. will flash blue.
Remove DC power and reapply DC power to activate the new EDID.
Use default EDID
IR Ports (Tx and Rx settings)
Troubleshooting
The IR ports are bi-directional, the IR receiver and IR emitter can be located on either the transmitter or on the receiver depending on your application.
(Transmit IR from your TV display to your equipment in another room) 1. Set the IR switch to (Rx)
switch to (Tx) on the 40-1090-3D-IR transmitter.
(Send IR commands to the display for control using the IR receiver) 1. Set the IR switch to (TX) on the 40-190-3D-IR receiver, 2. set the IR
switch to (Rx) on the 40-1090-3D-IR transmitter.
(Send IR commands to the display for control using a home automation control system) 1. Set the IR switch to (TX) on the 40-1090-3D-IR
receiver 2. set the IR switch to (Rx) on the 40-1090-3D-IR transmitter. 2 x 40-IRC cables are required one cable on the transmitter side and one on the
receiver side.
on the 40-1090-3D-IR receiver, 2. set the IR
Specifications
HDMI: 1.3 compliant, 3D capable, Video Resolutions: 480i/p, 720P, 1080i/p
Distances: Cat5e 62M (200 ft. max) 480i/p, 720p, 1080i, CAT5e 33M (110 ft. max) up to1080P, CAT6 43M (140 ft. max)@1080p @ 24/50/60Hz
DC Power: 2 x 5Vdc, 1A
IR Carrier frequency: 30-60Khz, IR signal tip and sleeve using Calrad 40-IRC IR adapter cable
IR Transmission: Bi-directional with settings on the transmitter and receiver for Tx and Rx
Receiver Function L.E.D.: Blue=using external power supply, Green=Power and HDMI signal received from transmitter unit, Yellow=no data input
or the signal is to weak.
Transmitter Function L.E.D.: Solid Blue=power on, Flashing Blue=TV EDID backup completed, Green=sending power or video to receiver unit,
Yellow=No data input or unsupported video format.
Connectors: HDMI: 2 x Female Jacks, Power: Transmitter, 1 x 2.1mm jack, Receiver, 1 x 2.1mm jack, Ethernet linking jacks: RJ45 (Female)
Size: Balun transmitter, receiver L-4.0” x W-2.6” x H-1.1”, Mounting: 4 hole slotted mounting system
Transmitter EDID Switch Settings (Setup), Extended Display Identification
Data. Please note! that the off position is up and the on position is down
Front
Back
Important read first!
1. The Cat5e, Cat6 wiring should be kept
away from any equipment that emits
strong electromagnetic interference such
as microwave ovens, high frequency
lighting or any type of AC high voltage
electrical wiring.
2. Do not connect the baluns into a
computer network, damage to the baluns
or network switch may occur. The baluns
will only work from the transmitter to the
receiver directly with no additional
hardware in the middle.
3. The HDMI cables from the transmitter
and receiver should not exceed 6 ft..
Please note ! This balun also supports
DVI-D signals and equipment, use the
appropriate adapters to convert to a HDMI
male plug.
Dip
Switch
Slide
Switch
No Video: 1. Make sure both the transmitter and receiver L.E.D. indicators are green, most common issues are related to the Cat5e, Cat6 cabling,
recheck and verify your wiring and RJ45 connections. 2. Use a factory pre-made ethernet cable to verify and quickly retest for signal. Check the
transmitter and the receiver for power with no ethernet cable connected. Verify that the all HDMI cables work independently of the baluns.
No IR: 1. Verify that the IR emitter flashes when a verified working remote control is pointed at the IR receiver and a command is sent. 2. Make sure
the Tx and Rx switches are correctly configured. 3. It may be necessary for certain products like cable boxes to use a non flashing ultraviolet L.E.D.
Calrad part no. 92-151 to properly control the device instead of the included flashing L.E.D. style emitter.
IR Emitter flashes but the equipment being controlled does not respond: 1. Verify the IR emitter is correctly placed over the controlled
equipments IR receiving window, 2. locate the receiver window by using the factory remote, turn the products power on that your testing, start from
the front of the face plate moving the remote from left to right while pressing the power button until the product turns off, this is the general area of the
IR receiver and is the location of where the IR emitter should be placed for continued testing.
Off
On
For technical assistance call: 323-465-2131