Cambridge Sound Works NEWTON s100 Multipole User manual

S100 MultiPole Surround Speakers
User Manual
®
™
™

2

3
INTRODUCTION
Thanks for choosing a Newton Series surround
loudspeaker. The S100 features the finest drivers,
precision internal crossover circuitry and an elegant
enclosure design.
The Product Development Team at Cambridge
SoundWorks believes there is no better combination of
audiophile-level attention to detail and reasonable cost.
AFTER UNPACKING
Store the shipping carton and packing material for
future use and transport.
CONTENTS
1. Two loudspeakers
2. Two No.10 screws and plastic wall anchors
3. Eight rubber feet
INSPECTING FOR DAMAGE
Examine the speaker system carefully for shipping
damage. If there is any, do not install or use the sys-
tem. Return the speaker to the store where you made
the purchase or call Cambridge SoundWorks at
1-800 FOR-HIFI (1-800-367-4434) for assistance.

4
POSITIONING YOUR SPEAKERS
The following suggestions assume you have some
flexibility regarding where you place your speakers.
Don’t be too concerned if your situation and listening
environment dictate the speakers’ position. As long
as each surround speaker is on the left or right half
of the listening space, the speakers are will provide
convincing, lifelike sound.
Mounting: The typical way to position surround speak-
ers is to wall-mount them on a protruding screwhead.
Other methods are to place them on short shelves, to
mount them on short swivel brackets, or to install them
on floor stands.
Notice: The speakers are marked LEFT and RIGHT.
Most often, the speakers will be wall-mounted with the
MultiPole switch panel facing down. In this case,
mount the LEFT speaker on the listener’s left side and
the RIGHT speaker on the listener’s right side (see
diagram A).
You may need to invert the speakers to provide
access to the MultiPole switch (such as when placing
them on small support shelves or floor stands). In this
case, reverse the speakers’ left/right positions (see
diagram B).
Front to Back placement: Place each surround speak-
er to the left or right of the listening area. Try to
position the speakers within two feet of a line centered
on your listening postion (see diagram C).
Height: Place each speaker at least four feet above
the floor, up to seven feet above the floor (see
diagram D).
Note: It is not critical that the left and right speakers
be the same distance from the front speakers or
equal heights.
If you don’t have walls on both sides of your listening
area, try to avoid placing both surround speakers on
a wall behind the listening postion. Sonically, it’s still
better to place one speaker on a side wall and one
speaker on a rear wall. This provides better separation
than two speakers on a wall behind the listeners.
S100
LEFT
8 Ohms
Made In China
WALLMOUNTED - SWITCH FACING DOWNWARD
RIGHT SPEAKER LEFT SPEAKER
7 Ft.
4 Ft.
Back of Speaker
Front to Back Placement
of Surround Speakers
Stand Mounted
Switch Facing Upward
Wall Mounted Height Placement
A.
B.
C.
D.
SPEAKERS ARE LABELED “LEFT” OR “RIGHT”
2FEET
2 FEET
CENTER LINE OF LISTENING POSITION

5
Hang the S100 directly on a wall:
Install a No.10 screw in the wall so that its screwhead
protrudes about 3/8 inch. Cambridge SoundWorks
supplies screws and plastic anchors for your conven-
ience, but it is the installer’s responsibility to insure the
screw is securely mounted.
Apply the soft, self-adhesive feet to back of the speak-
ers. The feet protect the finish of the speakers or the
surface and improve stability if the surface is not per-
fectly flat.
SPEAKER MOUNTING
S100
LEFT
8Ohms
Made In China
USE THIS KEYHOLE SLOT
TO HANG THE SPEAKER
FROM A SCREWHEAD.
USE THE THREADED
INSERT TO ATTACH
A SWIVEL BRACKET.
(SIDE VIEW)
(BACK VIEW)
APPLY SELF-ADHESIVE FEET TO
BACK OF SPEAKERS.
SWITCH

A small, purpose-built shelf can be used instead of
hanging the speakers from a screwhead. In this case,
we recommend you apply the soft, self-adhesive feet
to bottom of the enclosures. The feet protect the finish
of the speakers or the surface and improve stability if
the surface is not perfectly flat. Apply the feet to the
surface of the speaker opposite the MultiPole switch,
in the pattern shown.
Using The Speakers On A Stand
Cambridge SoundWorks Model ST300 floor-stands
may be used for the S100.
The speakers mount to the stand with the MultiPole
switch on top. For this reason, the positions of the
speaker should be reversed (the speaker marked left
should be placed on the listener’s right side and
vice versa).
Mount the surround speaker to a stand by screwing
the stand’s fastener into the surround speaker’s
threaded insert.
Swivel-brackets (available separately) can be used to
attach the surround speakers to a wall that isn't vertical,
or to the ceiling.
6
APPLY SELF-ADHESIVE FEET TO
BACK OF SPEAKERS.
BOTTOM OF SPEAKER
S100
LEFT
8O h ms
MadeIn China
ATTACHING SPEAKER TO STAND
NON-VERTICAL/CEILING MOUNTING
RIGHT SPEAKER LEFT SPEAKER
SWITCH SWITCH
SWIVEL BRACKET FOR NON-VERTICAL
OR CEILING MOUNTING

77
About MultiPole Technology
The MultiPole capability of your S100 speakers lets
you enjoy different types of surround programs at their
best. The descriptions that follow assume you will
position your surround speakers to the left and right of
the listening area and not directly behind it.
Dipole Mode: This mode provides everyone in the
listening space with enveloping surround. Most sound
is projected sideways (to the front and rear of the
room), while little is directed at the listeners (see
Dipole in the Multipole Modes diagram). As a result,
the sound is well mixed with room reflections, following
longer paths. In Dipole mode, a listener can be closer
to one surround speaker than the other and still hear
both surround speakers. This characteristic makes it
ideal for smaller rooms, where a listener may be closer
to one surround speaker than the other.
Dipole mode is ideal for use with synthesized surround
decoding modes; the choices on your decoder
labeled “Hall,” “Theater,” “Church,” or similar names.
Also, use it for Dolby Surround programs (the prede-
cessor to Dolby Digital and the format supported by
stereo TV programs with surround encoding). Dolby
Surround has a monaural surround channel which is
split between the two surround speakers. Dipole
mode’s dispersion pattern prevents this channel from
“collapsing” towards the closer surround speaker.
Bipole Mode: This mode “fills in the middle”
compared to Dipole mode. Each surround speaker
projects approximately equal amounts of sound to the
sides and at the listening area (see Bipole in the
Multipole Modes diagram). This makes it easier to
hear effects occurring between the left and right
surround speakers. Dolby Digital’s separate left and
right rear channels make this possible. The more
Dolby Digital program material you listen to, the more
you will benefit from Bipole mode. In larger listening
spaces, Bipole mode can even rival Dipole mode on
non-Dolby Digital program sources.
MultiPole Modes

88
Use at least 18 gauge speaker cable for short runs
(under 15 feet). Use 16 gauge or heavier speaker
cable for longer runs.
1. Determine how long the speaker cable should be
for each speaker. Cut the speaker cable into the
appropriate lengths.
2. Strip 1/2 inch of insulation from the two individual
conductors in the speaker cable. Twist the exposed
strands of bare wire together
3. Attach any connector plugs (like banana plugs) at
this time.
4. Determine which conductor you will use to connect
the positive terminals of the amplifier and speaker
together. One of the two conductors of a speaker
cable can usually be distinguished by printing or a
ridge on the insulation. Some times the metal of the
conductors has two different colors.
Make The Connections:
1. Press the speaker’s red and black connector knobs
to expose the holes in their shafts.
2. Insert the stripped end of one cable’s “indicated”
conductor into the speaker’s red (+) connector.
Release the knob to secure the connection. Make
sure no stray strands of wire are exposed.
3. Repeat the procedure for the cable’s other conduc-
tor and the speaker’s black (–) connector
4. Connect the other speaker cable’s conductors to the
other speaker.
5. Connect the opposite ends of the speaker cable to
the speaker outputs of your receiver. Remember to
observe channel and polarity (Left Positive, Left
Negative, Right Positive, Right Negative).
PREPARE THE SPEAKER WIRE
Strip off 1/2"
Twist Bare Wire

99
Dimensions: 4 5/16"H x 7 7/8"W x 4 5/16"D
Weight: 3 pounds each
The S100 can be safely used with any surround receiv-
er rated above 25 watts per channel. There is little
advantage gained in using more power than 100 watts
per surround channel, but amplifiers above this power
rating can be used so long as the receiver is not oper-
ated at distorted levels.
Warning About Excessive Amplifier Distortion
Operating a receiver (of any power rating) beyond its
maximum undistorted output level creates distortion—
added high-frequency sound not part of the musical
program. Distortion dramatically increases the internal
operating temperature of a loudspeaker and will even-
tually cause the speaker’s failure due to burned or
melted internal parts. While Cambridge SoundWorks
includes the most heat-tolerant parts commensurate
with good acoustic design, the speaker’s Limited
Warranty against defects in materials or workmanship
does not apply to parts that fail from long-term
operation at very high temperatures
Enclosure Cleaning
The speaker enclosures can be cleaned with a
window-cleaning product. Use a soft, lint-free cloth
only. Avoid spraying any cleaner on the grille panels.
Brush or vacuum the grille panels if dust accumulates
on them.
SPECIFICATIONS
Speaker Size Setting in Dolby Digital
Decoders
The S100 includes an internal high-pass network
that prevents it from responding to low-frequency sig-
nals below its operation range.
When connecting either speaker to a Dolby Digital
decoder, set the decoders rear channel size setting to
SMALL. If there is a crossover frequency choice, set
at 100 Hz or higher.

1010