Campania International Jensen FT-221 User manual

FT
-
221JensenFountain
Revised
May9, 2018
Pump KitPartsList
PK140 Pump (1)
#7 stopper(1)
8”length of½”blacknon-kinktubing (1)**
2”length of5/8”cleartubing (1)**
CopperSpillers (2)
1 oz. tube ofsilicone (1)
Wedges(2)
Hose clamps(1)*
*Hoseclampsmaybe used as flow restrictors
** Tubing has been preassembled
-WINTERCARE-
Fountainbowls/topsandotherfountaincomponents,whichcollect water, shouldnotbeleftoutsideinthewinter since anycomponent,
whichfillswithwater andfreezesmaycrack.Likewise, componentssuchaspedestals,whichremaininabasin,filledwithwater,
whichthenfreezes,mayalsocrackor crumble. Ideally, therefore, afountainshouldalwaysbestoredindoorsor inadryprotected
place suchasacoveredporchawayfromtheelements. However, ifafountainmustbeleftoutside:
(1) Removepump, rubber stoppers, drainpipes, finials,andother smallcomponentsfor storageindoors. Note that stoppersor
drainpipesareremovedtoallowdrainageintheeventwater accumulatesinanybasin.
(2) Raisefountainbasefromgroundwithwood stripssothat basewill notfreeze tothegroundsurface.
(3) Cover or wrapthefountainwithburlapor other absorbentmaterial (oldblanket or towel) andthencover securelywith
plastic,making surethat water will notaccumulate inthebasinor other fountaincomponentandfreeze;
(4) Checkfountainperiodicallytoensurethatplastic issecureandwater isnotaccumulating inanyfountaincomponent.
-GENERALFOUNTAINTIPS-
Install fountainsonalevel surface. Youwill needaproperlygrounded110-volt (AConly) GFCI protectedreceptaclenear the
fountainfor your pump. All pumpsaresubmersible andmustbecompletelyunderwater tofunctionproperly. Testall pumpsand
adjusttofull outputprior toassembly. Itisnotrecommendedthat fountainsbeplaceddirectlyongrass or dirt. Positionthechannel
opening at thebaseofeachfountaintoward theelectrical outlet tobeusedsince thepump
cord willbethreadedthroughthisopening.
CheckoutYouTubefor a“Howto”video.
For moreCampania product informationvisit www.campaniainternational.com
All of ourcaststone is proudly
FOUNTAININFORMATION:
Thisfountain holdsapproximately3gallonsof water.
Thisfountain usesamediumfountain cover.
(FTNCOV-MED)
Notrecommended for use with refillkits or LED
lightkits.
TOOLSREQUIRED:
Bubble Level
PUMPINFORMATION:
PF140 - 140GPH Pump
6FTcord length

FT
-
221JensenFountain
Revised
May9, 2018
Assembleyourfountain onalevelsurface capableofholdingaminimumof90 pounds withan
approximate1square footfootprint.
FT-221C(65lbs)
25.75”Lx18.25”Wx11”H
FT-221B(16lbs)
14.5”Lx9.75”Wx9.5”H
FT-221A(1lb)
4.25”Lx3”Wx4.75”H
1. Position thebasin (FT-221C) where thefountain is to be
installed, ensuringthatitislevel.
2. Assemblethepumpkit
a. NOTE: All pumpscomewith multipleadapters
b. This fountainusesthe largestadapter provided.
c. Using ahoseclamp, attachthe1/2”non-kink tubing
to thepumpoutlet.
d. Place thestopper aroundthepumpcord
approximately6”fromthepump.
3. Feedthepumpcordthrough theholeandchannelinthe
basin(FT-221C).
4. FIRMLY press thestopper intotheholeevenly.
a. Note:Usingthehandleofascrewdriverorhammer
worksbesttopressthestopperinplace.
5. Position thepedestalwithbowl(FT-221B)overthebasin
(FT-221C).
6. Fit theclear endofthetubingassemblyto thepipe
protruding fromthebottomofthepedestalwithbowl(FT-
221B).
7. Center and levelthepedestalwithbowl(FT-221B).
8. Using thesiliconeprovided,place thecopper spillers.
a. Cleanawayanyexcess silicone.
9. Fit thefinial(FT-221A)into thepedestalwithbowl(FT-
221B) bypushingtheprotruding CPVCpipefromthe
finialintotheCPVCcouplingonthebowl.
10.Letthefountainsit 24hoursbefore fillingwithwater.