CamTron ccd camera Manual

INFORMATION - This equipment has been tested and found to comply with
limits for a Class A digital device, pursuant to part 15 of the FCC Rules & CE Rules.
These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instruction manual, may cause
harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at
his own expense.
◆ Do NOT use power sources other than those specified.
◆ Do NOT expose this appliance to rain or moisture.
This installation should be made by a qualified service person and
should conform to all local codes.
The lightning flash with an arrowhead symbol, within an equilateral
triangle is intended to alert the user to the presence of uninsulated
dangerous voltage within the product's enclosure that may be of
sufficient magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert
the user to the presence of important operating and maintenance
(servicing) instructions in the literature accompanying the appliance.
WARNING - Changes or modifications not expressly approved by the
manufacturer could void the user's authority to operate the equipment.
CAUTION : To prevent electric shock and risk of fire hazards:
1
Ultra High Resolution Color Camera

Menu Flow 20
■Setup Page Menu 21
ㆍLENS 22
ㆍEXPOSURE 23
ㆍWhite Balance (White Bal.) 25
ㆍSSDR (Super Dynamic Range) 26
ㆍBACK LIGHT 27
ㆍDNR3 (Super Noise Reduction) 28
ㆍDAY/NIGHT 29
- IMAGE ADJ
- MONITOR
- CAM TITLE
- SYNS
- MOTION DET
- PRIVACY
- COMM ADJ
- LANGUAGE
- RETURN
ㆍSPECIAL 30
ㆍEXIT 36
31
32
32
33
34
34
35
36
36
Troubleshooting 37
Specifications 39
2
Ultra High Resolution Color Camera
3
Ultra High Resolution Color Camera
■Contents
Features
Precautions
Overview
Installation Procedures
■Front View
■Side View
■Bottom View
■Rear View
04
06
09
13
09
10
11
12
■Lens
ㆍUsing the auto iris
ㆍUsing a C/CS mount lens
■Connecting to a monitor
■Connecting to power
■Control via RS-485 Interface
13
17
18
19
Components and Accessories 08

4
Ultra High Resolution Color Camera
5
Ultra High Resolution Color Camera
Excellent Sensitivity
The built-in high sensitivity COLOR CCD
enable a clear image even in 0.15Luxor lower
illumination.
Ultra High Resolution
By adopting a diagonal 6mm(1/3") 410,000 (NTSC)
pixel, 470,000(PAL) pixel SONY CCD,
the camera produces clear picture quality with a
horizontal resolution of 600 TV lines for color.
Motion Detection
Since the camera detects motion without any
additional external sensor, you can monitor
activity more efficient.
DIS (Digital Image Stabilizer)
The DIS function compensates for any camera
movement, to produce more stable pictures.
DNR3 (Super Noise Reduction)
The high-performance W-V DSP chip effectively
removes low-light gain noise and afterimage to
provide clear images even in dark environments.
SSDR (Super Dynamic Range)
For images with high contrast between bright
and dark spots from difficult lighting conditions
such as backlighting, this camera selectively
illuminates darker spots while retaining the
same light level for brighter spots to even out the
overall brightness.
■Features Warning ■
The camera requires periodic inspection.
Contact an authorised technician to carry out the inspection.
Stop using your camera when you find it malfunctioning.
If the camera emits smoke or is unusually hot for a long period,
a fire may be caused.
Do not Install the camera on a surface that can not support it.
If the camera is installed on an inappropriate surface, it may fall
and cause injury.
Do not hold plug with wet hands.
It could cause an electric shock.
Do not dis-assemble the camera.
It may result in an electric shock or other hazards.
Do not use the camera close to a gas or oil leak.
It may result in a fire or other hazards.
Miscellaneous functions
HLC(High Light Compensation), SENS-UP,
FLIP (H/V-REV), D-ZOOM, SHARPNESS,
MOTION DETECTION and PRIVACY functions
are provided.
OSD
The camera control is convenient by using 8
different foreign language O.S.D.
- NTSC : Korean, English, French, Spanish,
Japanese, Portuguese
- PAL : English, French, German, Spanish,
Italian, Chinese, Russian, Czech, Polish
RS-485 Communication
Control Support
Remote OSD menu control via an RS-485
interface is supported.
Video/DC Drive Lens Support
You can select Video or DC Drive Lens from
the menu.
Day & Night
The camera identifies whether it is day or night
and automatically switches to the appropriate
mode, depending on its environment. By day,
the camera switches to color mode in order to
maintain optimal color. At night, it switches to
B/W mode so as to obtain better picture definition.

6
Ultra High Resolution Color Camera
7
Ultra High Resolution Color Camera
Do not install the camera in
extreme temperature conditions.
Do not install the camera under
unstable lighting conditions.
Do not touch the front lens of the
camera.
Only use the camera under conditions
where temperatures are between
-10˚C and +50˚C. Be especially
careful to provide ventilation when
operating under high temperatures.
It can cause the image quality to be
poor.
Severe lighting change or flicker can
cause the camera to work improperly.
This is one of the most important parts of
the camera. Be careful not to leave
fingerprints on the lens cover.
Do not install or use the camera in an
environment where the humidity is high.
ㆍIf the camera is exposed to spotlight or an object reflecting strong light,
smear or blooming may occur.
ㆍPlease check the power supply satisfies the normal specification before
connecting the camera.
It can cause malfunctions to occur.
If it gets wet, wipe it dry immediately.
Liquids can contain minerals that
corrode the electronic components.
If exposed to radioactivity the CCD
will fail.
It can damage the CCD.
Do not drop the camera and protect
it from physical shocks.
Do not expose the camera to rain
or spill beverage on it.
Do not expose the camera to
radioactivity.
Never keep the camera pointed
directly at strong light.
■Precautions

8
Ultra High Resolution Color Camera
9
Ultra High Resolution Color Camera
①Tripod Mounting Bracket Screw Hole
Used to fix the Tripod Mounting Bracket to the top of the camera.
②C-Mount Lens Adapter
Install this adapter to use a C-Mount Lens.
③Back Focus Control Lever
Adjust Back Focus using this control lever.
■Components and Accessories Overview ■
2. Auto Iris Lens Connector Plug
3. C-Mount Adapter
4. Instruction Manual
Front View
①
②
③
1. Ultra High Resolution
Day&Night CCD Camera

10
Ultra High Resolution Color Camera
11
Ultra High Resolution Color Camera
⑤Tripod Mounting Bracket Screw Hole
Used to fix the camera onto a bracket or tripod.
The screw sizes for this hole are as follows:
④Auto Iris Lens Connector
Used to connect Auto Iris Lens plug.
The Tripod Mounting Bracket can be unscrewed and
installed on the top or bottom of the camera.
Make sure to use the Tripod Mounting Bracket when
fixing the camera to a bracket or tripod, otherwise the
camera may be unstable and the internal circuitry of
the camera may get damaged.
Side View Bottom View
1/4"-20 UNC (20 THREAD)
L:4.5mm±0.2mm (ISO standard),
or 0.197" (ASA standard)
L
④
⑤
■Overview

12
Ultra High Resolution Color Camera
13
Ultra High Resolution Color Camera
Note
Lens
The lens is not supplied with this camera. Purchase a lens suitable for
the environment. This camera accepts an auto iris lens, and both
C-and CS-mount lenses.
• It is recommended to use the DC type Auto Iris Lens to effectively
enjoy the major functions of this camera.
• Keep the lens surface clean, as the picture quality suffers if
there is dirt or fingerprints on the Lens.
Using an Auto Iris Lens
1. Strip 8mm of insulation from the end of the Auto Iris Lens cable..
2. Strip 2mm of insulation from each of the cores of the cable.
⑪Video OUT Port
Video signals are output through this port. Connect this port to the Video IN
port of a Monitor/DVR.
⑬Power IN Port
Connections for Camera power, as specified for each model.
approx. 8mm
approx. 2mm
⑫Auto iris lens selection switch
Used to change between DC or Video depending upon the type of
auto iris in use.
Rear View
⑥
⑦
⑧
⑨
⑩
⑪
⑬
⑫
⑥OSD Setup Buttons
ㆍSET Button : Displays the menu on the screen. Press this button to confirm
status or after changing a selected item.
ㆍUp and Down Button : Used to move the cursor up or down in the menu
screen to select a desired menu item.
ㆍLeft and Right Button : Used to move the cursor left or right in the menu
screen or to change the value of the selected item.
⑦D & N Input Port (GND : BW, Open : Color)
Switch to Day or Night Mode by connecting an external signal to this port.
⑧MD Output Port
Motion detection signal is output through this port.
⑨RS-485 Control Port
The SETUP MENU can be controlled via this port using an external controller that
supports RS-485 communications. For details, see page 19.
⑩Power LED
When power is properly connected, the LED illuminates.
3±0.5sec
0V
There is motion
+4.0V ~ +4.5V (less than 10mA)
There is motion
■Overview Installation Procedures ■

14
Ultra High Resolution Color Camera
15
Ultra High Resolution Color Camera
3. Remove the cover of the Auto Iris Lens connector plug and solder the lens
cable to the connector pins of the plug.
4. Fit the cover of the auto iris lens connector
plug, remove the protective CCD cover
from the front of the camera, and fasten
the Auto Iris Lens by turning it clockwise.
5. Focus the camera using the Auto Iris Lens
controls, combined with fine adjustment using
using the Back Focus control.
•For a Video Drive Lens
Pin 1: Red (Power)
Pin 2: NC
Pin 3: White (Video Signal)
Pin 4: Black (Ground)
•For a DC Drive Lens
Pin 1: Damping -
Pin 2: Damping +
Pin 3: Drive +
Pin 4: Drive -
Using a C/CS mount lens
Before installing a lens, identify whether the lens to be installed is a C-Mount
or CS-Mount. This camera is set for a CS-Mount Lens by default. To install a
C-Mount Lens, a simple modification is required.
•When Using a CS Mount Lens
Remove the protective cover from the front of this product and turn the
CS-Mount Lens clockwise to install it. Focus the camera using the
CS-Mount Lens and Back Focus controls.
•Use a lens threaded as shown in the following figure. If the dimensions
of the thread are incorrect the camera could be damaged, or the lens
may not get installed firmly enough.
• If the lens is too heavy the camera becomes unbalanced, which may
cause problems. Use a lens weighing less than 450g.
•When adjusting the Automatic Level Control (ALC) of an Auto Iris Lens,
use Av mode if available. If Pk mode is used the picture brightness
may change continuously.
Note
connector
Lens cable
No. 3 Pin
No. 1 Pin
No. 4 Pin
No. 2 Pin
C-Mount Lens: 10mm or less
CS-Mount Lens: 5mm or less
Back Focus Control Lever
■Installation Procedures

16
Ultra High Resolution Color Camera
17
Ultra High Resolution Color Camera
•Using a C-Mount Lens
1 . Remove the protective cover at the front of this product and fit
the C-Mount Adapter, turn it clockwise to install it.
2. Turn the C-Mount Lens clockwise to install it.
3. Focus the camera using the C-Mount Lens and Back Focus controls.
Connecting to a Monitor
Connect the video output terminal located on the rear of the camera
to the Monitor/DVR.
• Since the connection procedure may differ depending on the type of monitor
or peripheral device to be connected, refer to the User Manual for the device
to be connected.
• Make sure to turn off the device to be connected before making any connections.
•Turn the 75Ω/Hi-Z switches of interim display devices to the Hi-Z position,
and the switches of any final device to the 75Ωposition.
CCD Camera
Monitor
CCD Camera
End monitor
Intermediate
4. Set the lens selection switch, located on
the rear of the camera, to either DC or VIDEO,
depending on the type of auto iris lens being
used.
■Installation Procedures

Control via RS-485 Interface
RS-485 Control Port
485 Control Board Connection Port
485+
(+) CONNECTION TERMINAL (TRX+)
(- ) CONNECTION TERMINAL (TRX-)
485-
Item
Initial value
PROTOCOL
UART MODE
BAUD RATECamera ID
STW
RET PKT
ENABLE
8-NONE-196000
The camera can be controlled by using an external controller equipped with
RS-485 communications.
• To control using a DVR or keyboard controller
Connect the RS-485 cable (TRX+, TRX-) to the connection port of the 485
control board in the DVR or controller.
* RS-485 communication default initial values
• To control the camera, adjust Protocol, Camera ID, Baud rate
in advance.
Note
18
Ultra High Resolution Color Camera
19
Ultra High Resolution Color Camera
Since power specifications differ depending on the model, make sure to check
your model name and specifications before connecting power.
You can connect power as shown in the following figure.
• Check the standard power requirement before connecting to power.
Connecting to Power
For AC / DC power
When the resistance value of copper wire is at [20˚C(68˚F)]
•As shown in the table above, voltage decreases as the wire gets longer.
Therefore use of an excessively long adaptor output line for connection to
the camera may affect the performance of the camera.
※Standard voltage for camera operation : DC 12V±10%, AC 24V±10%
※ There may be some deviation in voltage drop depending on the type of wire
and the manufacturer.
#24(0.22mm2)
Copper wire size(AWG)
#22(0.33mm2) #20(0.52mm2) #18(0.83mm2)
Resistance value( /m)
0.0180.030
0.050
0.078
Voltage drop(V/m) 0.0060.0110.0180.028
Dual Power Type
(AC 24V/DC 12V, AC 24V Class2)
DC Power Type (DC 12V, 500mA)
AC90~240V-50Hz/60Hz 4.5W
AC90~240V~
50Hz/60Hz 4.5W
■Installation Procedures

ㆍ MANUAL ㆍ VIDEO ㆍ DC
SETUP menu
LENS (selection)
EXPOSURE
WHITE BALANCE
SSDR
BACKLIGHT
DNR3
SPECIAL
EXIT
ㆍ BRIGHTNESS
ㆍ SENS-UP
ㆍ ATW
ㆍ MANUAL
ㆍ COMM ADJ
ㆍ IMAGE ADJ.
ㆍ SYNC
ㆍ OFF
ㆍ OFF
ㆍ OFF
DAY/NIGHT
ㆍ SHUTTER
ㆍ RETURN
ㆍ AWC→SET
ㆍ OUTDOOR
ㆍ LANGUAGE
ㆍ MONITOR
ㆍ MOTION DET
ㆍ ON
ㆍ ON
ㆍ BLC
ㆍ AGC
ㆍ INDOOR
ㆍ EXTERN
ㆍ AUTO ㆍ COLOR ㆍ B/W
ㆍ CAM TITLE
ㆍ PRIVACY
ㆍ RETURN
ㆍ HLC
ㆍ SAVE ㆍ NOT SAVE ㆍ RESET
■
Menu
1 . Press the SET button
ㆍ Settings can now be made. The SETUP menu is displayed on the monitor.
2. Select a menu item from the list available by using the UP and DOWN
buttons.
ㆍ Funtions are selected using up and down buttons.
ㆍ The selected position is displayed in blue.
MAIN MENU
1.LENS
2.EXPOSURE
3.WHITE BAL
4.SSDR
5.BACKLIGHT
6.DNR3
7.DAY/NIGHT
8.SPECIAL
9.EXIT
DC
SAVE
ATW
OFF
OFF
ON
COLOR
20
Ultra High Resolution Color Camera
21
Ultra High Resolution Color Camera
■How to Use the Camera
■
Settings
Settings can be made using the 5 buttons on the rear of the camera.
UP button
SET button
LEFT button
DOWN button
RIGHT button

MAIN MENU
1.LENS
2.EXPOSURE
3.WHITE BAL
DC
ATW
3. Set up a selected item by using the Left and Right buttons.
4. To finish and save the settings, select 'EXIT' and press the SET button.
Using this function, you can control the screen brightness.
2. Select the connected lens type by using the Left and Right buttons.
MAIN MENU
1.LENS
2.EXPOSURE
3.WHITE BAL
4.SSDR
5.BACKLIGHT
6.DNR3
7.DAY/NIGHT
8.SPECIAL
9.EXIT
DC
SAVE
ATW
OFF
OFF
ON
COLOR
Select the function using
the UP or DOWN button.
Change the status using
the LEFT or RIGHT button.
LENS
Note
•An item with the icon also has sub-menus. To select a sub-menu,
press the SET button.
•An item with the - - - icon has no sub-menus available for selection.
Note
• When using VIDEO lens, adjust the lens VR explained below first and
set the focus using 'FOCUS ADJ.' menu.
• If color rolling occurs when using a DC lens, set Shutter to A.FLK.
• Some lenses may not work properly, depending on the setting of the
BRIGHTNESS LEVEL.
• When Using a Video-Type Auto Iris Lens
① Adjust the ALC adjustment terminal on the lens appropriately.
In general, set it to AV (Average).
② It may not work properly depending on the installed lens. Set the
Level VR of the lens to the optimal value.
③ Set AGC to OFF and adjust the Lens VR to an appropriate brightness.
④ Adjust the Lens VR, adjust the BRIGHTNESS, and then check if the
screen brightness changes properly. Otherwise, adjust the Lens VR again.
1. When the SETUP menu screen is displayed, select 'LENS' by using the
Up and Down buttons so that the arrow indicates 'LENS'.
- Level (VIDEO) : Adjusts the level of video iris signals; the higher the
level is, the brighter the video looks.
- FOCUS ADJ. (DC, VIDEO) : To adjust the DC and VIDEO lens focus
correctly, you must activate the Focus Settings mode under each lens menu.
Activate the Focus Settings mode, adjust the lens focus, and then deactivate
the settings mode. (The VIDEO lens requires an extra step: go to the
sub menu of the Focus Settings mode and change the shutter speed
to adjust the lens brightness.)
- IRIS SPEED (DC) : Adjusts the Iris control speed of the DC lens. If the
control speed is too slow or fast, please use this menu to adjust the speed.
1. When the SETUP menu screen is displayed, select‘EXPOSURE’by
using the Up and Down buttons so that the arrow indicates‘EXPOSURE’.
EXPOSURE
2. Select a desired mode using the Up and Down buttons.
MAIN MENU
1.LENS
2.EXPOSURE
3.WHITE BAL
DC
ATW
●DC/Video : Select Auto Iris Lens
You can adjust the minimum shutter and maximum value
of ESC shutter mode when DC Lens mode is selected.
●Manual : Select Manual Lens
3. Each Lens mode has sub menu items as listed below.
- Brightness (DC, Manual) : Adjusts the video brightness.
22
Ultra High Resolution Color Camera
23
Ultra High Resolution Color Camera
■How to Use the Camera

Use the White Balance function to adjust the screen color.
1. When the SETUP menu screen is displayed, select 'White Bal.' by using
the Up and Down buttons so that the arrow indicates 'White Bal.' .
2. Select a desired mode using the Up and Down buttons.
White Balance (White Bal.)
● RETURN : Select this to save the changes in the EXPOSURE menu
and return to the SETUP menu.
Note
•When you use a DC lens, set the shutter mode to A.FLK if color rolling occurs.
•When the SHUTTER is set to MANUAL or A.FLK mode, SENS-UP will be disabled.
•When the SHUTTER is set to ESC after selecting the Internal Synchronization
Type, the picture may become unstable if the camera faces a bright fluorescent
light. Therefore, take care when choosing the installation position.
● SHUTTER : You can select either auto or manual shutter.
- A.FLK : Select this when you experience picture flicker, which can
happen when there is a clash with the frequency of the installed lighting.
- ESC : Select this to control the shutter speed automatically. If ESC is
selected, the shutter speed is automatically controlled depending
on the ambient illumination of the subject.
- MANUAL : You can control shutter speed manually. (1/60 ~ 1/120,000)
● AGC(AUTO GAIN CONTROL) : The higher the gain level, the brighter
the screen - but the higher the noise.
- OFF : Deactivates the AGC function.
- LOW : Allows automatic gain control from 5.3dB to 32dB.
- HIGH : Allows automatic gain control from 5.3dB to 37dB.
● SENS-UP : When it is night or dark, the camera automatically detects
the light level and maintains a clear picture if this mode is activated.
- OFF : Deactivates the SENS-UP function.
- AUTO : Activates the SENS-UP function.
Note
• If you press the SET button in 'AUTO' mode, You can adjust brightness
by increasing or decreasing the shutter speed. (X2~X512)
•Note that the higher the zoom level, the brighter the screen, but the
more likely it is that an after-image will appear.
• Although Noise, Spots, and Whitish symptoms may occur in SENS-UP
operation when the zoom level is increased, this is normal.
EXPOSURE SETUP
1.BRIGHTNESS
2.SHUTTER
3.AGC
4.SENS-UP
5.RETURN
25
ESC
HIGH
OFF
MAIN MENU
1.LENS
2.EXPOSURE
3.WHITE BAL
4.SSDR
5.BACKLIGHT
DC
ATW
OFF
OFF
※ Select one of the following 5 modes, as appropriate for your purpose.
● ATW : Select this when the color temperature is between 1,700˚K
and 11,000˚K.
●OUTDOOR : Select this when the color temperature is between 1,700˚K
and 11,000˚K. (sodium light inclusion)
●INDOOR : Select this when the color temperature is between 4,500˚K
and 8,500˚K.
●MANUAL : Select this to fine-tune White Balance manually. Set White-
Balance first by using the ATW or AWC mode. After that switch to MANUAL
mode, fine-tune the White Balance and then press the SET button.
● AWC→SET : To find the optimal luminance level for the current environment,
point the camera towards a sheet of white paper and press the Function
Setup switch. If the environment changes, readjust it.
24
Ultra High Resolution Color Camera
25
Ultra High Resolution Color Camera
■How to Use the Camera

MAIN MENU
1.LENS
2.EXPOSURE
3.WHITE BAL
4.SSDR
5.BACKLIGHT
DC
ATW
OFF
OFF
SSDR (Super Dynamic Range)
This camera is designed so that it delivers a distinctive subject and background
at the same time, even when the subject is in backlight, unlike conventional
cameras, by adopting a proprietary W-V DSP chip.
1. When the SETUP menu screen is displayed, select 'BACKLIGHT' by
using the Up and Down buttons so that the arrow indicates 'BACKLIGHT'.
Note
• White Balance may not work properly under the following conditions.
In this case select the AWC mode.
①When the color temperature of the environment surrounding the
subject is out of the control range (e.g. clear sky or sunset).
②When the ambient illumination of the subject is dim.
③If the camera is directed towards a fluorescent light or is installed
in a place where illumination changes dramatically, the White Balance
operation may become unstable.
SSDR illuminates darker spots of an image while retaining the same light
level for brighter spots to even out the overall brightness of images with high
contrast between bright and dark spots.
1. When the SETUP menu screen is displayed, select 'SSDR' by using the
Up and Down buttons so that the arrow indicates 'SSDR'.
2. Use the Left/Right buttons to change the SSDR level in the sub menu
according to the contrast between bright and dark spots.
MAIN MENU
1.LENS
2.EXPOSURE
3.WHITE BAL
4.SSDR
5.BACKLIGHT
DC
ATW
OFF
OFF
● BLC : Enables a user to directly select a desired area from a picture,
and to view the area more clearly.
● HLC (High Light Compensation) :
If the scene contains extremely brightly light areas such as; from car
headlight, the light can mask out much of the on-screen detail. Use
HLC feature to remove these exceptionally brightly light areas to allow
detail such as car number plates to become visible.
-LEVEL : Adjust level of the HLC function.
-LIMIT : Enable to change the operating condition.
- MASK COLOR/TONE : Change the color / brightness of the masking area.
(Black, Red, Blue, Cyan, Magenta)
-TOP/BOTTOM/LEFT/RIGHT : Adjust the area to be enhanced.
SSDR OFF
SSDR ON
BACKLIGHT
2. Select a desired mode using the Left and Right buttons depending on the
camera purpose.
BLC OFF
BLC ON
26
Ultra High Resolution Color Camera
27
Ultra High Resolution Color Camera
■How to Use the Camera

HLC SETUP
LEVEL
LIMIT
MASK COLOR
MASK TONE
TOP
BOTTOM
LEFT
RIGHT
Press SET to Return
MIDDLE
NIGHT ONLY
BLACK
1
5
120
5
172
BLC SETUP
LEVEL
TOP
BOTTOM
LEFT
RIGHT
MIDDLE
38
109
54
121
Press SET to Return
MAIN MENU
1.LENS
2.EXPOSURE
3.WHITE BAL
4.SSDR
5.BACKLIGHT
6.DNR3
7.DAY/NIGHT
DC
ATW
OFF
OFF
ON
COLOR
You can display pictures in color or black and white.
1. When the SETUP menu screen is displayed, select 'DAY/NIGHT' by using
the Up and Down buttons so that the arrow indicates 'DAY/NIGHT'.
● OFF : Not being used
● Select 'BLC' to adjust the area to be
enhanced then adjust the level.
● HLC : Enable the user to change the
level, limit, mask color/tone and area.
3. Select a desired mode using the Left and Right buttons and press the SET button.
DAY/NIGHT
This function reduces the background noise in a low luminance environment.
1. When the SETUP menu screen is displayed, select 'DNR' by using the
Up and Down buttons so that the arrow indicates 'DNR'.
DNR3
HLC OFFHLC ON
HLC MASKING AREA
Note
• For effective license plate observation, it needs minimum illumination and
fast shutter speed more than 1/200sec.
• Because there can be a difference in the effectiveness of HLC according
to the amount of light area in the screen, optimize the installation angle for
the best HLC performance.
• When dark, the HLC is only activated when a bright light exceeding a
specific size.in NIGHT ONLY mode.
• The HLC is not activated in day light or when bright light is not present
at night.in NIGHT ONLY mode.
MAIN MENU
1.LENS
2.EXPOSURE
3.WHITE BAL
4.SSDR
5.BACKLIGHT
6.DNR3
7.DAY/NIGHT
DC
ATW
OFF
OFF
ON
COLOR
● OFF : Deactivates DNR. Noise is not reduced.
● ON : Activates DNR so that noise is reduced.
2. Select a desired mode using the Left and Right buttons.
3. Set the DNR mode to 'ON' and press the SET button. Then you can
adjust the noise reduction level.
Note
• You cannot set the DNR to 'ON' or 'OFF' when the AGC mode of the
EXPOSURE menu is 'OFF'.
• When adjusting the noise reduction level in the DNR mode, remember
that the higher the level set, the more the noise level will be reduced,
as will the brightness of the image.
■How to Use the Camera
28
Ultra High Resolution Color Camera
29
Ultra High Resolution Color Camera

2. Select a desired mode using the Left and Right buttons according to the
picture display you want.
1. When the SETUP menu screen is displayed, select 'SPECIAL' by using
the Up and Down buttons so that the arrow indicates 'SPECIAL'.
SPECIAL
Note
• When using a Video Auto Iris Lens, if you set the lens level to low,
automatic switching between Color and Black & White may not occur.
• When AGC in the EXPOSURE menu is 'OFF', the exchange between
DAY mode and NIGHT mode operates as like selecting 'COLOR' mode.
● IMAGE ADJ. :
1) When the SETUP menu screen is displayed, select 'IMAGE ADJ.'
by using the Up and Down buttons so that the arrow indicates 'IMAGE ADJ'.
2) Select a desired mode using the Up and Down buttons.
• V-REV : You can flip the picture vertically on the screen.
• H-REV : You can flip the picture horizontally on the screen.
• D-ZOOM : You can use a digital zoom of x1 ~ x16.
• DIS (Digital Image Stabilizer) : This function mitigates any picture
movement due to external factors such as wind.
2. Select a desired mode using the Up and Down buttons.
● COLOR : The picture is always displayed in color.
● B/W : The picture is always displayed in black and white.
You can turn on or off the burst signal on B/W mode.
● AUTO : The mode is switched to 'Color' in a
normal environment, but switches to 'B/W'
mode when ambient illumination is low.
To set up the switching time for AUTO mode,
press the SET button.
You can turn on or off the burst signal on
B/W mode.
- DWELL TIME : You can select the duration time about changing the
day/night mode. → 5s, 7s, 10s, 15s, 20s, 30s, 40, 60s
● EXTERN : This mode allows you to apply a desired filter to external signals.
MAIN MENU
1.LENS
2.EXPOSURE
3.WHITE BAL
4.SSDR
5.BACKLIGHT
6.DNR3
7.DAY/NIGHT
8.SPECIAL
9.EXIT
DC
SAVE
ATW
OFF
OFF
ON
AUTO
SPECIAL
1. IMAGE ADJ
2. MONITOR
3. CAM TITLE
4. SYNS
5. MOTION DET
6. PRIVACY
7. COMM ADJ
8. LANGUAGE
9. RETURN
LCD
OFF
INT
OFF
OFF
ENGLISH
IMAGE SETUP
1. V-REV
2. H-REV
3. D-ZOOM
4. DIS
5. FONT COLOR
6. SHARPNESS
7. RETURN
OFF
OFF
OFF
OFF
BLUE
ON
AUTO SETUP
1.BURST MODE
2.COLOR→B/W
DURATION
DWELL TIME
3.B/W→COLOR
DURATION
DWELL TIME
4.RETURN
ON
FAST
3 SEC
FAST
10 SEC
30
Ultra High Resolution Color Camera
31
Ultra High Resolution Color Camera
■How to Use the Camera

Note
• When the V-REV or H-REV mode is enabled, the text on the screen
does not flip.
• If you increase the SHARPNESS level too high, the picture may become
distorted or noise may appear.
● MONITOR : Please change the settings value of video appropriate to
your monitor.
- LCD : Please select this menu item when
using an LCD monitor.
- CRT : Please select this menu item when
using a CRT monitor.
- USER : Please use this menu item when
using a monitor other than standard
ones. You can change the gamma,
PED level, and color gain in the sub menus.
CAMERA TITLE SETUP
M
LK
JIH
GF
ED
CBA
ZYXWVUTSRQPON
mlkjihgfedcba
z
yx
wvu
ts
rq
pon
987654321.-
DNES
OP
RLC→ ←
FRONT DOOR
● CAM TITLE : If you enter a title, the title will appear on the monitor.
1) If the SPECIAL menu screen is displayed, use the Up and Down
buttons so that the arrow indicates 'CAM TITLE'.
2) Set it to 'ON' by using the Left and Right buttons.
3) Press the SET button.
Note
• When the CAM TITLE menu is 'OFF', no title will be displayed on the
monitor screen even if you enter one.
• Only English is available in this mode.
• If you move the cursor to CLR and press the SET button, all the letters
are deleted. To edit a letter, change the cursor to the bottom left arrow
and press the SET button. Move the cursor over the letter to be edited,
move the cursor to the letter to be inserted and then press the SET button.
●SYNC : In areas where the supply is at 60Hz,
you can synchronize the output phase
of multiple cameras using the power
synchronization function (Line-Lock)
without using a synchronization
signal generator.
- INT : Internal Synchronization Type
- L/L : Power Synchronization Type, Line-lock
• Press the Function Setup switch.
• You can select a desired phase from 0 to 359 when select 'phase'.
Note
• As the DIS function uses the digital zoom the camera's resolution will
decrease.
• DIS doesn't operate when background illumination is too low.
• DIS doesn't operate when object pattern is monotonic as like sky or
white wall.
• FONT COLOR : You can change the OSD font color.
(White, Yellow, Green, Red, Blue)
• SHARPNESS : As you increase this value, the picture outline becomes
stronger and clearer. Adjust this value appropriately
depending on the sharpness of the picture.
• RETURN : Select this to save the settings for the IMAGE ADJ. menu
and to return to the SETUP menu.
4) Use the 4 direction buttons to move
to a desired letter and select the letter
by pressing the SET button. Repeat
this to enter multiple letters. You can
enter up to 15 letters.
5) Enter a title, move the cursor to 'POS'
and press the SET button. The entered
title appears on the screen. Select the
position to display the title on the screen
by using the 4 direction buttons and
press the SET button. When the position
is determined, select 'END' and press
the SET button to return to the
SPECIAL menu.
Note
• When using AC power at 60Hz frequency, you can use the L/L type
synchronization.
• When the power is DC 12V, the SYNC menu is fixed to the 'INT' mode.
GAMMA
PED LEVEL
COLOR GAIN
RESET
32
Ultra High Resolution Color Camera
33
Ultra High Resolution Color Camera
■How to Use the Camera

●COMM ADJ (Communication Adjustment) :
This function sets up the camera communication status when controlling
the camera through an external control device.
1) When the SPECIAL menu screen is displayed, press the Up and
Down buttons so that the arrow indicates 'PRIVACY'.
2) Set up the mode using the 4 direction buttons.
- AREA SEL : You can select up to 12 PRIVACY areas.
- MODE : Determines whether to use the area selected in the AREA SEL.
- MASK COLOR : Determine area color. You can select Green, Red,
Blue, Black, White, Gray.
- MASK TONE : Adjust the brightness of MASK COLOR.
- TOP/BOTTOM/LEFT/RIGHT : Adjust the size and position of the
selected area.
- RETURN : Select this to save the PRIVACY menu settings and
return to the SPECIAL menu.
PRIVACY AREA SETUP
1. AREA
2. MODE
3. MASK COLOR
4. MASK TONE
5. TOP
6. BOTTOM
7. LEFT
8. RIGHT
9. RETURN
AREA1
OFF
GREEN
1
39
79
12
51
●MOTION DET :
This product has a feature that allows you
to observe movement of objects in 8 different
areas on the screen, and the words
'MOTION DETECTED' appear on the screen
when movement is detected.
you can monitor activity more efficient.
1) When the SPECIAL menu screen is displayed, press the Up and
Down buttons so that the arrow indicates 'MOTION DET'.
2) Set up the mode using the 4 direction buttons.
- SENSITIVITY : You can select up to 8 MD areas. When SENSITIVITY
number is high, motion detection sensitivity is increased to recognize
even small movement.
- AREA MODE : Determines whether to use the MD area selected
in SENSITIVITY.
- SEL POS : Determines which of the 4 vertices of each MD area
is to be used.
- YPOS : Determines the coordinate of the vertical axis for SEL POS.
- XPOS : Determines the coordinate of the horizontal axis for SEL POS.
- FILL→SET : Fills in a selected MD area. Fills in a selected MD area.
The color of filling is sequentially selected as brown, orange, blue,
cyan, yellowish green, yellow and red.
- RETURN : Select this to save the MOTION DET menu settings
and return to the SPECIAL menu.
●PRIVACY : Mask an area you want to hide on the screen.
COMM SETUP
1.CAM ID
2.BAUD RAET
3.UART MODE
4.RET PKT
5.DISP ID
6.PROTOCOL
7.RETURN
2
4800
8-N-1
DISABLE
OFF
PELCO-D
①When the SPECIAL menu screen is displayed, press the Up and
Down buttons so that the cursor points to 'COMM ADJ'.
②Set up the mode using the 4 direction buttons.
- CAM ID : Determines the camera's identification number.
(between 0 and 255).
- BAUD RATE : Select 2400/4800/9600/19200/38400/57600 bps.
- UART MODE : Select NONE, EVEN or ODD for the parity bits.
- RET PKT : Determines whether to send a command back to the
controller device when a communication control
command is sent to the camera.
- DISP CAM ID : Display the camera title on the top left corner
of the screen.
- PROTOCOL : STW(SPD), PELCO-D, PELCO-P, SEC, BOSCH
HONEY WELL, VICON, PANA
34
Ultra High Resolution Color Camera
35
Ultra High Resolution Color Camera
■How to Use the Camera

EXIT
●LANGUAGE : You can select the menu language according to your
requirements.
●RETURN : Select this to save the SPECIAL menu settings and return
to the MAIN SETUP menu.
Select a desired EXIT mode using the Left and Right buttons depending
on the camera purpose.
- SAVE : Save the current settings and exit the MAIN SETUP menu.
- NOT SAVE : Do not save the current settings and exit the MAIN SETUP menu.
- RESET : Resets the camera settings to the factory defaults. Language and
Monitor settings are not initialized.
■How to Use the Camera Troubleshooting ■
36
Ultra High Resolution Color Camera
37
Ultra High Resolution Color Camera
If you have trouble operating your camera, refer to the following table.
If the guidelines do not enable you to solve the problem, contact an
authorized technician.
Problem
Nothing appears on
the screen.
The image on the
screen is dim.
•Check the power connections.
•Check the VIDEO signal line connection.
• Make sure the lens is clean. Clean the lens with a
soft clean lint free cloth.
•Adjust the monitor contrast & brightness controls.
• Re-position the camera if necessary.
The image on the
screen is dark.
•Adjust the contrast control of the monitor.
•
If you have an intermediate device, set the 75Ω/ Hi-z
properly.
The camera is not working
properly, and the surface
of the camera is hot.
•Check that an appropriate power source is
connected to the camera.
The DAY/NIGHT menu
does not work.
•Check that AGC in the EXPOSURE menu is set
to 'OFF'.
The SENS-UP function
does not work.
•Check that AGC in the EXPOSURE menu is not
set to 'OFF'.
•Check that SHUTTER in the EXPOSURE menu
is not set to 'A.FLK' or 'MANUAL'.
Solution

Problem
The Motion Detection
function does not
work.
Color is not correct.
•Check that MOTION DET in the SPECIAL SETUP
is not set to 'OFF'.
• Check the WHITE BAL settings in the SETUP menu.
The screen flickers
continually.
•Check that the camera isn't facing toward a bright
light source, such as the sun.
RS-485
communication fails.
•Check the polarity between the RS-485 Control Port
and the RS-485 cable.
• Check the RS-485 Communication settings.
Solution
RS-485 Control Port 485 Control Board Connection Port
485+ (+) CONNECTION TERMINAL (TRX+)
(-) CONNECTION TERMINAL (TRX-) 485-
38
Ultra High Resolution Color Camera
39
Ultra High Resolution Color Camera
Specifications (AC24V / DC12V) ■
ITEM
Image Sensor
Total Pixels
Effective Pixels
Scanning System
Synchronization
Frequency
SONY 1/3" Super HAD High Sensitivity Color CCD
811(H) x 508(V) 795(H) x 596(V)
768(H) x 494(V) 752(H) x 582(V)
2:1 Interlace
INT
Horizontal : 15.734 KHz, Vertical:59.94 Hz Horizontal : 15.625 KHz, Vertical:50.00 Hz
600 TV lines
52dB (AGC Off, Weight ON)
NTSC PAL
Power Consumption
H.Resolution
S/N
Min. Illumination
White Balance
Shutter Speed
Sens-up
Gain Control
DNR
Motion Detection
Privacy Function
V-REV
H-REV
Freeze
Sharpness
Day&Night
DIS
Digital Zoom
Blemish Compensation
Lens Mount
Back Focus Adjustment
0.15Lux (40 IRE)
ATW / AWC / MANUAL(1700˚K ~11,000˚K)
1/60,1/50 ~ 1/120,000 sec
AUTO / OFF (Selectable x2 ~ x512)
LOW / HIGH / OFF
ON / OFF (1~32 Level)
ON / OFF (8 Zone, ALARM Output)
ON / OFF (12 Zones)
ON / OFF
ON / OFF
ON / OFF
ON/OFF (Level Adjustable)
COLOR / Black&White / AUTO / EXT
ON / OFF
ON / OFF (x16)
256 point (Even 128 Point, Odd 128 Point)
CS Mount (Easy Focus type)
(C Mount is mountable by using adaptor)
Manual
-10˚C to + 50˚C / 30% to 80% RH
-20˚C to + 60˚C / 20% to 90% RH
320g
Operating temperature / Humidity
Storing Temperature / Humidity
Weight
AC24V / DC12V DC12V
170mA(AC24V)/260mA(DC12V) 160mA
AC24V / DC12V DC12V
170mA(AC24V)/260mA(DC12V) 160mA
■Troubleshooting