CANADA BILLARD & BOWLING INC REBEL User manual

REBEL Installation manual
2021-03-20
CANADA BILLIARD & BOWLING INC.
4050 Industriel blvd, Laval, QC, H7L 6C3
450-963-5060
W W W.CANADABIL LIARD.COM

LIFETIME GUARANTEE
CANADA BILLIARD is pleased to offer an unsurpassed LIFETIME GUARANTEE TO THE ORIGINAL PURCHASER
against defects in material and workmanship, provided installation and/or service is performed by an
Authorized Dealer or a factory-approved installer. Cloth, pockets and rail cushions are not covered under
this guarantee. CANADA BILLIARD warrants that those specific parts are to be free from defects at date
of installation.
ALL CLAIMS MUST BE MADE THROUGH AN AUTHORIZED DEALER OR REPRESENTATIVE. Parts returned
for warranty service are to be shipped «prepaid». Those parts found to be defective will be repaired or
replaced by CANADA BILLIARD at its sole discretion, and returned «prepaid» by conventional surface
freight carrier. Any costs or charges required to disassemble, prepare for return and reassemble will be
the sole reponsibility of the owner. This guarantee does not imply the replacement of the entire pool table
but does cover the replacement or repair of such parts that may prove to be defective.
Replacement or repair of defective parts shall
constitute complete fulfillment of all obligations of
CANADA BILLIARD with respect to product guarantee.
CANADA BILLIARD shall under no circumstances incur
liabilitities for any consequential damages arising out
of any condition of the pool table, including but not
limited to, damages arising from the use or loss of use
of the product.
There are no warranties which extend beyond the description on the face hereof. No other express or
implied warranties of merchantability or fitness for particular use, whether oral or written, shall apply
to the product. CANADA BILLIARD neither assumes nor authorizes, any person to assume on CANADA
BILLIARD’s behalf, any other obligation or liability in connection with the product.
This guarantee does not apply to damage resulting from transit, moving, abuse, misuse, accident,
alteration, neglect, climatic conditions, normal wear and tear, fire, flood, earthquake or any other natural
calamity. Billiard tables used in an institutional or commercial application are not covered by this
g uar antee.
CANADA BILLIARD reserves the right to improve any product through changes in design or materials
without obligation to incorporate such changes in products of prior manufacture. This warranty is personal
and non-transferable to subsequent owners of the table. CANADA BILLIARD’s obligation hereunder is void
if the table is not installed and serviced by an authorized CANADA BILLIARD’s Dealer or Representative.

Install on the short base frame 3/8"-16 x 4 1/2"
threaded rods and dowel pins.
6 With help, install two corner legs with 3/8"-16 x
4 1/2" hexagonal bolts and 7/16" flat washers.
Repeat for the two other corner legs. Fasten all bolts.
4
2 Unwrap legs and unscrew leg levellers
for about 1/4.
1 Place the hardware on a clean surface.
5 Join the short and long base frame and fasten with
3/8"-16 hexagonal nuts and 7/16" flat washers.
3 On a clean floor, place the long and short base
frames.

12 Level the table with corners leg levelers.
10 Installe the short end crossmembers withe 3/8"-16 x 1
3/4"! hexagonal nuts and 7/16" flat washers.
8 Before fastening those legs, by pulling then up, be
sure that the joints between the legs and the frames
are close. At this point, the table must stand on it's
corner legs alone.
Install the long crossmembers into the base frame.
9
11 Install the short center crossmembers. These last
pieces, as for the short end crossmembers, must be
installed slightly lower that the base frame.
7 Keeping the centre leg's levelers completely screwed.
install them with 3/8"-16 x 4 1/2" hexagonal bolt and
7/16" flat washers.

18 Check the proper leveling of each slate section.
16 Start by correctly positionning the center section.
14 With help, dispose of the slate sections on the base
frame.
17 Put together all the slate section
15 Make sure to keep about 1" inbetween them.
13 Unscrew the center leg levelers to the floor.

24 Install the tacking strip for the corners using the
same screws.
22 Fix them underneath the slate using 2" wood screws
#14.
20 If needed, use wedges and fill the joint with slate
joint wax,"plasco" ciment or light body filler.
21 Pace the tacking strips on the table.
19 Check the joints.
23 Install the tacking strip for the sides using the same
screws.

1
2
3
4
28 Staple 4" on center of one end of the table.
30 Pulling tightly toward #1, staple approx. 4".
Repeat for #2, #3 and #4.
26 Cut 1 1/2" wide strip of cloth. Spray adhesive on
all pocket entries. Spray adhesive on one side of
the cloth strips and glue one to each pocket entry.
6
4
3
5
1
2
29 Pulling toward #2, staple on #2. Repeat for #3.
Pulling tightly toward #4, staple approx. 4".
Repeat for #5 and #6.
27 Place the cloth over the slate with
tag "playing surface" on top.
25 Using a wood ripper, adjust corner's and side's
tacking strips to the slate pocket openings.

36 Locate rail attachment holes and cut clearance
on cloth with a sharp knife (approx. 1/2" dia).
34 Cut 5 to 6 slits at the 4 corner pocket cuts out.
Stretch and staple under the pocket cuts out. Repeat
for each corner by stretching the cloth.
32 Pulling tightly toward #1, staple approx. 4".
Repeat for #2, #3 and #4.
2
1
35 Stretch and staple all sides.
Cut excess of cloth.
33 Pulling toward #1, staple approx. 4". Repeat for #2.
Repeat for each of the corner pockets.
31 Pulling toward #2, staple on #2. Repeat for #3.
Pulling tightly toward #4, staple approx. 4".
Repeat for #5 and #6.

42 Close side joints simultaneously.
40 Proceed the same way
for all rails.
38 Place the dowels pins 5/8" x 2". Place
the A part in one of the holes and screw
the B part into the A part.
41 Considering the size of a 12 feet snooker table,
consider assembling two "U" shape section of rails
upside down before carefully turning them over.
39 Fasten the end rail #1 to the side rail #2.
Place the C part on B rod and turn the
threaded sphere with the small key
provided to tighten the assembly.
37 Use counter bolts to
assemble the rails.

48 Assemble the frame using 1/4"-20 x 1 1/2"
machine screws and 5/16" flat washers.
46 CAREFULLY put the sides aprons unside down on the
rails and installe the metal plate witn 1/4"-20 x 5/8"
machine screws ans 5/16" flat washers.
44 Install 3/8"-16 x 3 3/4" threaded rods into the rails
throught the slate holes.
47 With help, install the long side aprons underneath the
rail. Fix it with only two 1 1/4" #8 wood screws. Be
sure to properly align the apron side joint with the
rail side joint.
45 Install loosely 3/8" lockwashers and 3/8"-16
hexagonal nuts.
43 Underneath the table, use the counter bolts the fix
the the side rails assembly.

52 Fasten the leather straps under the slate
slabs with #8 1/2" screws.
50 Align the side rails and
tighten all the rails.
51 Nail the pockets. Make sure all the surface
covers the rails. Screw the leather pocket
strips the framed slate with #7 x 1/2".
49 Once all aprons are in place, sccrew the them
onto the rails using #8 x 1 1/4" wood screws.

CANADA BILLIARD & BOWLING INC.
4050 Industriel blvd, Laval, QC, H7L 6C3
450-963-5060
W W W.CANADABILLIARD.COM
YOU ARE NOW READY
TO PLAY YOUR FIRST GAME OF SNOOKER ON
YOUR MAGNIFICENT SNOOKER TABLE FROM
CANADA BILLIARD !
CONGRATULATIONS !