Candy CTP644MCBB/1 User manual

Instruction Manual For Induction Hob ENGLISH
Manual de instruções para placa de indução PORTUGUÊS
Használati útmutató indukciós főzőlaphoz MAGYAR
Instrukcja obsługi płyty indukcyjnej POLSKI
Εγχειρίδιο οδηγιών για επαγωγική εστία ΕΛΛΗΝΙΚΑ
MODEL: CTP644MCBB/1
THANK YOU FORPURCHASING THE CANDY INDUCTION HOB. PLEASE READ THIS INSTRUCTION
MANUAL CAREFULLY BEFORE USING THE HOB KEEP IT IN A SAFE PLACE FORFUTURE REFERENCE.

1
Download hOn App
In the hOn App you’ll have access to several recipes and
extra contents

2
SAFETY WARNINGS
PLEASE READ THE FOLLOWING INSTRUCTIONS
CAREFULLY BEFORE USING THE APPLIANCE.
Installation
Electrical Shock Hazard
•Disconnect the appliance from the mains electricity supply
before carrying out any work or maintenance on it.
•Connection to a good earth wiring system is essential and
mandatory.
•Means for disconnection must be incorporated in the fixed
wiring in accordance with the wiring rules.
•Alterations to the domestic wiring system must only be
made by a qualified electrician.
•Failure to follow this advice may result in electrical shock
or death.
Cut Hazard
•Take care - panel edges are sharp.
•Failure to use caution could result in injury or cuts.
Important safety instructions
•Read these instructions carefully before installing or using
this appliance.
•No combustible material or products should be placed on
this appliance at any time.
•Please make this information available to the person
responsible for installing the appliance as it could reduce
your installation costs.
•In order to avoid a hazard, this appliance must be installed
according to these instructions for installation.

3
•This appliance is to be properly installed and earthed only
by a suitably qualified person.
•This appliance should be connected to a circuit which
incorporates an isolating switch providing full
disconnection from the power supply.
•WARNING: Use only hob guards designed by the
manufacturer of the cooking appliance or indicated by the
manufacturer of the appliance in the instructions for use as
suitable or hob guards incorporated in the appliance. The
use of inappropriate guards can cause accidents.
•Failure to install the appliance correctly could invalidate
any warranty or liability claims.
•Regarding the details of installation, thanks to refer to the
section <Installation>.
Operation and maintenance
Electrical Shock Hazard
•Do not cook on a broken or cracked cooktop. If the cooktop
surface is break or crack, switch the appliance off
immediately at the mains power supply (wall switch) and
contact a qualified technician.
•Switch the cooktop off at the wall before cleaning or
maintenance.
•Failure to follow this advice may result in electrical shock
or death.
Health Hazard
•This appliance complies with electromagnetic safety
standards.
Hot Surface Hazard

4
•During use, accessible parts of this appliance will become
hot enough to cause burns.
•Do not let your body, clothing or any item other than
suitable cookware contact the ceramic glass until the
surface is cool.
•Metallic objects such as knives, forks, spoons and lids
should not be placed on the hob surface since they can get
hot
•Children less than 8 years of age shall be kept away unless
continuously supervised.
•Handles of saucepans may be hot to touch. Check saucepan
handles do not overhang other cooking zones that are on.
Keep handles out of reach of children.
•Failure to follow this advice could result in burns and
scalds.
Cut Hazard
•The razor-sharp blade of a cooktop scraper is exposed when
the safety cover is retracted. Use with extreme care and
always store safely and out of reach of children.
•Failure to use caution could result in injury or cuts.
Important safety instructions
•Never leave the appliance unattended when in use.
Boil-over causes smoking and greasy spillovers that may
ignite.
•Never use your appliance as a work or storage surface.
•Never leave any objects or utensils on the appliance.
•Never use your appliance for warming or heating the room.
•After use, always turn off the cooking zones and the
cooktop as described in this manual (i.e. by using the touch
controls). Do not rely on the pan detection feature to turn
off the cooking zones when You remove the pan.

5
•Do not allow children to play with the appliance or sit,
stand, or climb on it.
•Do not store items of interest to children in cabinets above
the appliance. Children climbing on the cooktop could be
seriously injured.
•Do not leave children alone or unattended in the area where
the appliance is in use.
•Children or persons with a disability which limits their
ability to use the appliance should have a responsible and
competent person to instruct them in its use. The instructor
should be satisfied that they can use the appliance without
danger to themselves or their surroundings.
•Do not repair or replace any part of the appliance unless
specifically recommended in the manual. All other
servicing should be done by a qualified technician.
•Do not use a steam cleaner to clean your cooktop.
•Do not place or drop heavy objects on your cooktop.
•Do not stand on your cooktop.
•Do not use pans with jagged edges or drag pans across the
glass surface as this can scratch the glass.
•Do not use scourers or any other harsh abrasive cleaning
agents to clean your cooktop, as these can scratch the
ceramic glass.
•If the supply cord is damaged, it must be replaced by the
manufacturer, its service agent or similarly qualified
persons in order to avoid a hazard.
•This appliance is intended to be used in a domestic
household environment only! Commercial use of any kind
is not covered under the manufacturer's warranty!

6
•WARNING: The appliance and its accessible parts become
hot during use. Young children should be kept away.
•Care should be taken to avoid touching heating elements.
•Children less than 8 years of age shall be kept away unless
continuously supervised.
•This appliance can be used by children aged from 8 years
and above and persons with reduced physical, sensory or
mental capabilities or lack of experience and knowledge if
they have been given supervision or instruction concerning
use of the appliance in a safe way and understand the
hazards involved.
•Children shall not play with the appliance. Cleaning and
user maintenance shall not be made by children without
supervision.
•WARNING: Unattended cooking on a hob with fat or oil
can be dangerous and may result in fire. NEVER try to
extinguish a fire with water, but switch off the appliance
and then cover flame e.g. with a lid or a fire blanket.
•WARNING: Danger of fire: do not store items on the
cooking surfaces.
•WARNING: If the surface is cracked, switch off the
appliance to avoid the possibility of electric shock, for hob
surfaces of glass-ceramic or similar material which protect
live parts.
•A steam cleaner is not to be used.
•The appliance is not intended to be operated by means of an
external timer or separate remote-control system.
•CAUTION: The cooking process has to be supervised. A
short term cooking process has to be supervised

7
continuously.
•Power cord can’t accessible after installation.
Product Overview
Top View
CTP644MCBB/1
1. 1800 W zone, boost to 2100 W
2. 1800 W zone, boost to 2100 W
3. 1800 W zone, boost to 2100 W
4. 1200 W zone, boost to 1500 W
5. 3000 W zone, boost to 3600 W
6. Control panel

8
The Control Panel
CTP644MCBB/1
Product Information
The ceramic/induction hob can meet different kinds of cuisine demands because of
resistance wire heating, micro-computerized control and multi-power selection, really
the optimal choice for modern families.
The hob centers on customers and adopts personalized design. The hob has safe and
reliable performances, making your life comfortable and enabling to fully enjoy the
pleasure from life.
1. ON/OFF control 6. Boost control
2. Heating zone selection controls 7. Pause control
& Power regulating key 8. Keep warm
3. Timer regulating control 9. Automatic detection
4. Keylock control 10. Flexible zone
5. Energy efficiency

9
A Word on Induction Cooking
Induction cooking is a safe, advanced, efficient, and economical cooking technology. It
works by electromagnetic vibrations generating heat directly in the pan, rather than
indirectly through heating the glass surface. The glass becomes hot only because the
pan eventually warms it up.
Before using your New Hob
•Read this guide, taking special note of the ‘Safety Warnings’ section.
•Remove any protective film that may still be on your induction hob.
Using the Touch Controls
•The controls respond to touch, so you don’t need to apply any pressure.
•Use the ball of your finger, not its tip.
•You will hear a beep each time a touch is registered.
•Make sure the controls are always clean, dry, and that there is no object (e.g. a
utensil or a cloth) covering them. Even a thin film of water may make the
controls difficult to operate.
iron pot
magnetic circuit
ceramic glass plate
induction coil
induced currents

10
Choosing the right Cookware
•Only use cookware with a base suitable for induction cooking. Look for the
induction symbol on the packaging or on the bottom of the pan.
•You can check whether your cookware is suitable by carrying out a magnet
test. Move a magnet towards the base of the pan. If it is attracted, the pan is
suitable for induction.
•If you do not have a magnet:
1. Put some water in the pan you want to check.
2. Follow the steps under ‘To start cooking’.
3. If does not flash in the display and the water is
heating, the pan is suitable.
•Cookware made by the following materials is not
suitable: pure stainless steel, aluminum or copper
without a magnetic base, glass, wood, porcelain, ceramic,
and earthenware.
Size of burner (mm)
The minimum cookware (diameter /mm)
160
120
180
140
210
180
280
180
Flexible zone
250
Do not use cookware with jagged edges or a curved base.
Make sure that the base of your pan is smooth, sits flat against the glass, and is the same
size as the cooking zone. Always centre your pan on the cooking zone.
Always lift pans off the ceramic hob – do not slide, or they may scratch the glass.

11
Use pans whose diameter of the ferromagnetic area (base of the pan) is in the
range of dimensions in the table below. (Table 1)
- If you use smaller pots, performance could be affected
- If you use pot with a diameter smaller than the one indicated in the table
above, pots may not be detected
According to the dimension of the zone you can use pots of different diameters
as picture below:
If the ferromagnetic part covers only partially the base of the pan, only the
ferromagnetic area will heat up, the rest of the base may not heat up a
sufficient temperature for cooking.
If the ferromagnetic area is not homogeneous, but presents others material
such as aluminum this may affect the heating up and the pan detection.
If the base of the pan is similar to the pictures below the pan could be not
detected.

12
Using your Induction Hob
To start cooking
•After power on, the buzzer beeps once, all the indicators light up for 1 second then
go out, indicating that the hob has entered the state of standby mode.
1. Touch the ON/OFF switch. all the indicators show “– “
2. Place a suitable pan on the cooking zone that you wish to use.
Make sure the bottom of the pan and the surface of the
cooking zone is clean and dry.
3. Select a heat setting by touching the “slider” control.
•If you don’t choose a heat setting within 1 minute,
the Induction hob will automatically switch off.
You will need to start again at step 1.
•You can modify the heat setting at any time during
cooking.
When you have finished cooking
1. Turn the cooking zone off by touching “slider”control
down to“0”. Make sure the display shows“0”.
2. Turn the whole hob off by touching the ON/OFF
control.
3. Beware of hot surfaces
“H” will show which means cooking zone is too hot to touch. It
will disappear when the surface has cooled down to a safe
temperature. It can also be used as an energy saving function if
you want to heat further pans, use the hotplate that is still hot.

13
Using the Power Management
It is possible to set a maximum power absorption level for the induction hob, choosing
up to different power ranges.
Induction hobs are able to limit themselves automatically in order to work at lower
power level, to avoid the risk of overloading.
To enter the power management function
1. Turn on the hob, then press at the same time the “+”(timer) and Pause. The time
indicator will show “P5” which means power level 5. The default mode is on 7.2Kw.
To switch to another level
Press +/- from the timer. There are 5 power levels, from “P1” to “P5”. The timer
indicator will show one of them.
“P1”: the maximum power is 2.5 Kw.
“P2”: the maximum power is 3.5 Kw.
“P3”: the maximum power is 4.5 Kw.
“P4”: the maximum power is 5.5 Kw.
“P5”: the maximum power is 7.2 Kw.
OR
Confirmation and Exit Power Management Function
Press at the same time the “+”(timer) and Pause for confirmation, then the hob will be
turned off.

14
Using Boost function
Activate the boost function
1. Touch the slider control of which zone you want to select.
Note: The power setting of bridge zone works the same as any other normal area.
2. Touch the booster key when the display is blinking,
power level indication shows “P”.
Cancel Boost function
1. Touching the “slider” to cancel the Boost function, and
select the level you want to set.
• Boost function can only last for 5 minutes, after that the zone will go to level 9
automatically.
Using Energy Efficiency Function
For induction hobs, the better pot you use, the more efficiency you will get. This EE
function can automatically detect the quality of pots and show the efficiency you use.
Activate the Energy Efficiency function
Press the EE button, EE% indicator will light up. Display will
show the percentage of power you use.
If the timer, keylock or EE functions are activated at the same time, it will indicate the
corresponding information alternately.
Cancel the Energy Efficiency function
Press the EE button, EE% indicator will go out and the function is
canceled.

15
Using the Keep Warm function
Activate the Keep warm function
1. Touch the slider control of which zone you want to set.
2. Touching the keep warm control, the zone indication
shows “ |”
Cancel the Keep warm function
Touch the slider control of which zone you want to cancel the Keep warm, then the
cooking zone will revert to the level you select.
Using the Pause function
1. Press the Pause control, the heating zones stop working. All the zone indication
show“||”
2. Press the Pause control once again, all the heating zones will revert to its
original setting.
The function is available when one or more heating zones are working.
If you don`t cancel the stop working mode within 30 minutes, the induction hob
will automatically switch off.
Locking the Controls
•You can lock the controls to prevent unintended use (for example children
accidentally turning the cooking zones on).
•When the controls are locked and heating zones are working, all the controls except
the ON/OFF and Pause are disabled.

16
To lock the controls
Touch the keylock control.
The timer indicator will show “Lo “.
To unlock the controls
1. Make sure the hob is turned on.
2. Touch and hold the keylock control for 3 seconds.
3. You can now start using your hob.
When the hob is in lock mode and without heating zone working, all the controls
are disabled excepting the ON/OFF, you can always turn the hob off with the
ON/OFF control in an emergency, but you shall unlock the hob first in the next
operation.
Residual Heat Warning
When the hob has been operating for some time, there will be some
residual heat. The letter “H” appears to warn you to keep away from it.
Using Flexible zone function
This may be used as a single zone or two individual zones depending on the
cooking needs in each situation.
It is made of two independent coils that can be controlled separately. When the
flexible zone is working, only the zone covered by the cookware is activated. This
function only works on 1# and 2# cooking zones.
To ensure that the cookware is detected and heat is distributed evenly, correctly
centre the cookware.

17
One hob with more than one flexible zone, it is not recommended to use several
zones at the same time for a single pan.
Activate Flexible zone function
1. To activate the flexible area as a single big zone, touch the key. The buzzer
beeps indicating that the induction hob enters selection of flexible zone, and the
corresponding indicator will flash.
2. Select the power level you want to set by touch “Slider”control.
Cancel Flexible zone function
1. Touch the key to cancel the flexible zone function.
2. The power setting works the same as any other normal area.

18
Auto Shutdown
Safety feature of the hob is auto shut down. This occurs whenever you forget to switch
off a cooking zone. The default shutdown times are shown in the table below:
Power level
1
2
3
4
5
6
7
8
9
Default working timer (hour)
8
8
8
4
4
4
2
2
2
Using the Timer
You can use the timer in two different ways:
You can use it as a minute minder. In this case, the timer will not turn any cooking
zone off when the set time is up.
You can use it as cut-off timer to turn one or more cooking zones off after time is
up.
You can set the timer up to 99 minutes.
Using the Timer as a Minute Minder
1. Make sure the hob is turned on. And zone selection key is not activated (zone
indication ‘-’ is not blinking).
Note: You can set minute minder before or after cooking zone power setting finished.
2. Set the time by touching “+””-”.
Press the “+” once increases the time by one minute, Press
the “-” once decrease the time by one minute. When the set
time exceed 99 minutes, it will automatically return to “00”,
if the “-” and “+” keys are pressed simultaneously, the
indicator will display “00”.
3. When the time is set, it will begin to count down immediately. The display will
show the remaining time.
4. Buzzer will beeps for 30 seconds and the timer indicator
shows “- - ” when the setting time finished.
Using the timer to switch off one or more cooking zones

19
1. Press the slider control of which cooking zone you want to
set the timer for.
2. Set the time by touching “+” “-”.
Press the “+” once increases the time by one minute, Press the
“-” once decrease the time by one minute. When the set time
exceed 99 minutes, it will automatically return to “00”, if the “-”
and “+” keys are pressed simultaneously, the indicator will
display “00”.
3. When the time is set, it will begin to count down immediately. The display will show
the remaining time.
NOTE: There will be a red dot in the right bottom corner of power level indication
which indicating that zone is selected.
4. When cooking timer expires, the corresponding cooking zone will be switch off
automatically.
Note: Other cooking zones will keep operating if they are turned on previously.
If the timer is set on more than one zone:
1. When you set timer for several cooking zones, red dots of the relevant cooking
zones are indicated. The timer display shows the min. timer. The dot of the
corresponding zone blinks.
(set to 15 minutes)
(set to 45 minutes)
2. Once the countdown timer expires, the corresponding zone will switch off. Then it
will show the new min. timer and the dot of corresponding zone will flash.