Canmax CM-2D600 User manual

1. Configuration Flowchart
2. Product Overview
3. Einstellen
Scanners
des
3-1. Operation Mode
3-2. Output Interface in Ca le mode
After scanning Enter barcode, specify which output interface
the device works with in Cable mode.
4. Basic Scanner Operations
You can perform most of below basic operations by either
scanning the barcode sequences or using the button triggers.
4-1. Mode Switch
Button Trigger
Keep holding Scan utton till the LED light turns from a rapidly
blinking color into a solid color. After a release of Scan utton,
you, by observing the LED light colors, can learn which
operation mode your scanner is switched to.
Scan Sequence
After reading ENTER label, scan the below appropriate
barcode to switch to the desired operation mode.
4-2. Transmit all arcode data
Button Trigger
Step 1 Secure the interface cable to both the barcode reader
and the Host PC Open the preferred word processing
software to receive the scanned data.
Step 2 After holding Small Trigger long enough to trigger off a
solid LED light, release Small Trigger.
Step 3 While the orange LED starts flashing rapidly, press Scan
utton once again to transmit all barcode data.
Scan Sequence
Scan Data Memory Tx barcode after reading Enter label.
4-3. Clear all saved arcode data
Button Trigger
Step 1 Configure the scanner to be in Memory mode.
Step 2 While holding Small Trigger till orange LED starts
*A40C3*
Bluetooth
*A40C2*
Cable+Mem
*A40C4*
Cable
+BT
*A40C5*
Mem+BT
*A40C6*
Cable+Mem+BT
*B21D1*
USB HID
*B21D2*
USB C M
*B21D3*
RS232
*ZTOS*
To Cable Mode
*ZTOM*
To Mem Mode
*ZTOB*
To BT Mode
*ZMTX*
Data Memory Tx
○
1
Press Scan Button to read barcodes.
○
2
Press Small Tirgger to perform supplementary fucntions.
○
3
Good Read Indicator indicates whether the barcode is
decoded. Green LED shows a successful decodeing attempt.
○
4
Mode Indicator indicates the current operation mode status.
lue LED stands for luetooth mode, green LED for Cable mode,
and orange LED for Memory mode
○
5
Power Indicator indicates the battery charge status.
when the battery is running low, red LED light will be on
to show a poor charge level. Once the charging
process is completed, red LED will flash slowly to show
a full battery charge.
○
6
Strape Hole
○
7
Secure the interface cable into USB Port to charge the
battery or transmit data.
○
8
Replace the battery in the battery compartment.
desired
barcodes
ENTER barcode
*/$%ENTR*
END barcode
*ZEND*
Please make sure you always start a scan sequence with ENTER
barcode and end with END barcode as a successful attempt.
We offer a selection of mode combinations, including 3 in1
functions, for your convenience to improve efficiency at work.
efore reading the below barcodes, please scan Enter label first to
ensure a successful configuration.
2 1
3
*A40C0*
Cable
*A40C1*
Memory

blinking rapidly, press down Scan Button.
Step 3 Release Scan Button and Small Trigger.
Scan Sequence
First read Enter label, and then scan the following barcode:
4-4. Clear one single data
Button Trigger
Step 1 Configure the scanner to be in emory mode.
Step 2 In emory mode, Press down Small Trigger and scan
the barcode you want to remove from the flash memory.
4-5. Auto-delete all transmitted data
You may program the scanner by scanning Enable label to
auto delete the barcode data that was just transmitted after
reading Enter barcode.
4-6. Attempt a firmware update
Please read Enter label first, and then scan ISP barcode before
applying relative scanner firmware updates.
5. How to Make your Scanner Work with a
Bluetooth HID Dongle
5-1. Pair with Bluetooth HID Dongle
Step 1 ake sure the Bluetooth dongle is well secured into
the USB port of the Host PC.
Step 2 Scan ENTER barcode.
Step 3 Scan To BT Mode barcode to enter Bluetooth mode.
Step 4 Press down either Scan Button or Small Trigger to recover
Bluetooth connection. A solid Blue LED indicates a successful
attempt.
Step 5 Open the referred word processing software to receive
the scanned barcode data.
5-2. Disa le the pairing function
Once a Bluetooth connection is established, Disable the pairing
function, after scanning Enter barcode, to avoid the incident of
mistakenly repeating the pairing process.
5-3. Type of Bluetooth connection
The type of Bluetooth connection varies according to the
Bluetooth device you attempt to pair the scanner with.
Whenever you need to establish a Bluetooth connection, specify
this information out of six alternatives provided.
Use the supple entary progra , "Barcode S
*B87A1*
Enable
*B87A0*
Disable
*ZISP*
ISP
*ZTOB*
To BT Mode
*BE280*
Disable
*BE281*
Pair
*BE1D1*
SPP Slave
*BE1D2*
SPP Master
*BE1D3*
HID
*BE1D4*
iOS
*BE1D5*
A303
*BE1D6*
A302
*ZFCA*
Data Me ory Clear
2D wireless
Barcode
Reader
Quick Start
5
4