Canmax CM-2D601 User manual

1
1. Product Overview
2. Decimal/Hexadecimal Table
3. How to set up a Bluetooth connection with
iO devices
Step 1
Step 1Step 1
Step 1 Configure output interface of the scanner to
be iOS
iOSiOS
iOS by scanning the sequence of barcodes as the
below figure shows.
Step 2
Step 2Step 2
Step 2 Switch your scanner to Bluetooth Mode.
Step 3
Step 3Step 3
Step 3 Pair your scanner with iOS de ices.
Step 4
Step 4Step 4
Step 4 Turn on Bluetooth setting in your iOS Product.
From the list of a ailable Bluetooth de ices,
appropriately select the de ice which your intend to
pair iOS product with.
○
1
Press Scan Button to read barcodes.
○
2
Press Small T
Small TSmall T
Small Tri
riri
rigger
gger gger
gger
to perform supplementary fucntions.
○
3
Good Read Indicator
Good Read IndicatorGood Read Indicator
Good Read Indicator inidicates whether the barcode is
decoded. Green LED shows a successful decodeing
attempt.
○
4
Mode Indicator
Mode Indicator Mode Indicator
Mode Indicator indicates the current operation mode
status. Blue LED
stands for Bluetooth mode, green LED for
Cable mode, and orange LED for Memory mode
○
5
Power Indicator
Power Indicator Power Indicator
Power Indicator indicates the battery charge status.
○
6
Strape Hole
Strape HoleStrape Hole
Strape Hole
○
7
Secure the interface cable into USB Port
USB Port USB Port
USB Port to charge the
battery or transmit data.
*%00*
0
*%01*
1
*%02*
2
*%04*
4
*%05*
5
*%03*
3
*%07*
7
*%08*
8
*%06*
6
*%0A*
A
*%09*
9
*%0D*
D
*%0B*
B
*%0C*
C
*%0E*
E
*%0F*
F
*%OK*
SET
*/$%ENTR*
ENTER
*ZEND*
END
*5OZ4*
iOS
*/$%ENTR*
ENTER
*ZPAR*
BT Pairing
2D wireless
Barcode
Reader
Quick Start
*/$%ENTR*
ENTER
*
ZTOB
*
To BT Mod

2
Step 5
Step 5Step 5
Step 5 According to the pop-up message which
contains PinCode info, please properly scan the
sequence of decimal barcodes from
Decimal/Hexadecimal Table in Section 2. Then, scan
SET
SETSET
SET label in the same table to initiate the pin code
erification.
Step 6
Step 6Step 6
Step 6 After Bluetooth connection is successfully
established, press Home button and launch Notes
NotesNotes
Notes
application to recei e barcode data.
4. How to set up a Bluetooth connection with
Android devices
Step 1
Step 1Step 1
Step 1 Configure output interface of the scanner to
be HID
HIDHID
HID by scanning the sequence of barcodes as the
below figure shows.
Step 2
Step 2Step 2
Step 2 Switch your scanner to Bluetooth Mode.
Step 3
Step 3Step 3
Step 3 Pair your scanner with Android de ices.
Step 4
Step 4Step 4
Step 4 Turn on Bluetooth setting in your Android
de ice. From the list of a ailable Bluetooth de ices,
appropriately select the de ice which your intend to
pair Android phone with.
Step 5
Step 5Step 5
Step 5 According to the pop-up message which
contains PinCode info, please properly scan the
sequence of decimal barcodes from
Decimal/Hexadecimal Table in Section 2. Then, scan
SET
SETSET
SET label in the same table to initiate the pin code
erification.
Step 6
Step 6Step 6
Step 6 After Bluetooth connection is successfully
established, launch a text editing application to recei e
barcode data.
5. How to set up a Bluetooth connection with
termial programs via PP Master interface
Step 1
Step 1Step 1
Step 1 After the Bluetooth dongle is secured into Host
PC, please go to Control Pane
Control PaneControl Pane
Control Panel>Bluetooth Settings
Bluetooth SettingsBluetooth Settings
Bluetooth Settings.
Step 2
Step 2Step 2
Step 2 In Bluetooth
Bluetooth Bluetooth
Bluetooth Settings
SettingsSettings
Settings, click on COM Ports
COM PortsCOM Ports
COM Ports tab
and then hit Add
AddAdd
Add button to add an incoming port.
Step 3
Step 3Step 3
Step 3 In Add COM Port
Add COM Port Add COM Port
Add COM Port dialogue box, select
Incoming
IncomingIncoming
Incoming option and then hit OK
OK OK
OK button to initiate
the process.
Step 4
Step 4Step 4
Step 4 Back to Bluetooth Setting
Bluetooth SettingBluetooth Setting
Bluetooth Setting, if the incoming
port is successfully generated, the list box in COM
COM COM
COM
ports
portsports
ports tab will show associated information
regarding the incoming port.
Step 5
Step 5Step 5
Step 5 Launch the terminal simulation application to
configure COM Port with the incoming port you
generate in step 4 and ensure the application is
connected using specified COM port.
Step 6
Step 6Step 6
Step 6 Configure output interface of the scanner to
be SPP Master
SPP MasterSPP Master
SPP Master by scanning the sequence of barcodes
as the below figure shows.
*/$%ENTR*
ENTER
*ZEND*
END
*
5OZ3
*
HID
*/$%ENTR*
ENTER
*ZPAR*
BT Pairing
*/$%ENTR*
ENTER
*ZEND*
END
*
5OZ2
*
SPP Ma
s
t r
*/$%ENTR*
ENTER
*
ZTOB
*
To BT Mod

3
Step 7
Step 7Step 7
Step 7 Follow the below steps to configure pin code
information.
Step
Step Step
Step 8
88
8 Follow the below steps to configure MAC
address information.
Step
Step Step
Step 9
99
9 Switch your scanner to Bluetooth Mode.
Step
Step Step
Step 10
1010
10 Pair your scanner with Android de ices.
Step 1
Step 1Step 1
Step 11
11
1 When the system successfully detects the
scanner, a pop-up message will appear around
Bluetooth icon on the taskbar. Click on the message to
prompt Add a de ice
Add a de iceAdd a de ice
Add a de ice dialogue box to proceed with
relati e configurations.
Step 1
Step 1Step 1
Step 12
22
2 Following through the configuration,
appropriately enter the paring code which you specify
in step 7 for the pin code erification.
Step 13
Step 13Step 13
Step 13 Once Bluetooth connection is successfully
established, switch back to the terminal program to
recei e barcode data.
6. How to set up a Bluetooth connection using
Bluetooth HID Dongle
Step 1
Step 1Step 1
Step 1 Configure output interface of the scanner to
be HID
HIDHID
HID-
--
-A302
A302A302
A302 by scanning the sequence of barcodes
as the below figure shows.
Step 2
Step 2Step 2
Step 2 Follow the below steps to configure MAC
address information.
Step 3
Step 3Step 3
Step 3 Secure Bluetooth Hid dongle into Host PC.
Step 4
Step 4Step 4
Step 4 Switch your scanner to Bluetooth Mode.
*/$%ENTR*
ENTER
*ZPAR*
BT Pairing
*/$%ENTR*
ENTER
*ZEND*
END
*
5OZ6
*
HID
-
A302
*
A4W+
*
BtMacAdd
*/$%ENTR*
ENTER
According to the actual
MAC address of the
dongle, scan the sequence
of barcodes from
decimal/hexadecimal table
in Section 2.
*%OK*
SET
*ZEND*
END
*
D6O+
*
BtMacAddr
*/$%ENTR*
ENTER
According to the
actual MAC address
of the dongle, scan
the sequence of
barcodes from
decimal/hexadecim
al table in Section 2.
*%OK*
SET
*ZEND*
END
*
95C+
*
BtPinCod
*/$%ENTR*
ENTER
Scan the sequence of
barcodes
corresponding to the
desired pin code from
decimal/hexadecimal
table in Section 2.
*%OK*
SET
*ZEND*
END
*/$%ENTR*
ENTER
*
ZTOB
*
To BT Mod
*/$%ENTR*
ENTER
*
ZTOB
*
To BT Mod

4
Step
Step Step
Step 5
55
5 Pair your scanner with Android de ices.
Step
Step Step
Step 6
66
6 Launch a text editing program to recei e
barcode data.
7. Basic canner Operations
7-1. Mode witch
Please follow the below steps to attempt mode
switch among Cable mode, Bluetooth mode and
Memory mode.
7-2. Transmit all barcode data
Step 1
Step 1Step 1
Step 1 Ha e your scanner secured into Host Pc with
USB interface.
Step 2
Step 2Step 2
Step 2
Please scan the sequence of barcodes as
the following figure shows.
Step 3
Step 3Step 3
Step 3 Press down Scan Button to transmit the sa ed
barcode after launching a text-editing application.
7-3. Clear all saved barcode data
Please scan the sequence of barcodes as the
following figure shows.
*/$%ENTR*
ENTER
*ZPAR*
BT Pairing
*ZTOS*
To Cabl Mod
*ZTO *
To M m Mod
*ZTOB*
To BT Mod
*/$%ENTR*
ENTER
*
Z TX
*
Data M mory Tx
*/$%ENTR*
ENTER
*/$%ENTR*
ENTER
*
ZFCA
*
Data M mory Cl ar