Canon Cine-Servo User manual
E3
Introduction
Introduction
Documentation includes the printed Lens Manual, Information Display CD-ROM.
Refer to this Information Display Manual for operating instructions and procedures for the information display.
E4
Introduction
Contents
Introduction E3
General Safety Information ............................................................................E7
Handling the Product .......................................................................................................... E8
Dealing with Abnormalities .................................................................................................E9
Maintenance and Inspection ..............................................................................................E9
Storage ............................................................................................................................... E9
To the Customer ...............................................................................................................E10
Manual Layout ............................................................................................... E11
Manual Conventions .........................................................................................................E12
Part Names ....................................................................................................E13
Part Names and Functions ............................................................................................... E13
Using the Control Keys .....................................................................................................E13
Basic Sequence of Operations ....................................................................E14
1. Screen Organization E15
1.1 Top Screen ..............................................................................................E16
1.2 Menu Screen ........................................................................................... E18
2. Mode Selection E21
2.1 Modes ...................................................................................................... E22
3. Operation in Basic Mode E23
......................................................E24
3.1.1 Selecting Basic Mode .............................................................................................. E25
3.1.2 Top Screen ..............................................................................................................E26
3.1.3 Specifying Auto Iris Gain .........................................................................................E28
3.1.4 Assigning Functions to the AUX Switch ...................................................................E29
E5
Introduction
3.1.5 Auto-Adjusting the Mechanical End .........................................................................E30
3.1.6 Assigning Functions to the AUX1 Switch .................................................................E31
3.1.7 Zoom Tracking ON/OFF .......................................................................................... E32
3.1.8 Assigning Functions to the AUX2 Switch .................................................................E33
3.1.9 Specifying Iris Torque ..............................................................................................E34
3.1.10 Specifying Zoom Curve Mode ............................................................................... E35
................................................... E37
3.2.1 User Screen Settings .............................................................................................. E38
3.2.2 Switch Screen Settings ........................................................................................... E44
3.2.3 Preset Screen Settings ............................................................................................E48
3.2.4 Iris Screen Settings .................................................................................................E52
3.2.5 Zoom Screen Settings ............................................................................................. E59
3.2.6 Focus Screen Settings ............................................................................................ E63
3.2.7 Info Screen Settings ................................................................................................E65
3.2.8 Fol. Screen Settings ................................................................................................ E72
3.3 List of Settings ........................................................................................E74
4. Operation in Full Mode E77
......................................................E78
4.1.1 Selecting Full Mode ................................................................................................. E79
4.1.2 Top Screen ..............................................................................................................E80
4.1.3 Switching Users .......................................................................................................E82
4.1.4 Switching to Basic Mode .........................................................................................E83
4.1.5 Auto-Adjusting the Mechanical End .........................................................................E84
4.1.6 Specifying Iris Gain ................................................................................................. E85
4.1.7 Zoom Tracking ON/OFF .......................................................................................... E87
4.1.8 Assigning Functions to the AUX Switch ...................................................................E88
4.1.9 Specifying Iris Torque ..............................................................................................E89
4.1.10 Assigning Functions to the AUX1 Switch ...............................................................E90
4.1.11 Assigning Functions to the VTR Switch .................................................................E91
4.1.12 Assigning Functions to the AUX2 Switch ...............................................................E92
4.1.13 Assigning Functions to the RET Switch .................................................................E93
4.1.14 Specifying Zoom Curve Mode ............................................................................... E94
4.1.15 Assigning Functions to the Seesaw .......................................................................E96
4.1.16 Specifying Iris A/M Switch .....................................................................................E97
4.1.17 Escape Operation ..................................................................................................E98
E6
Introduction
................................................... E99
4.2.1 User Screen Settings ............................................................................................ E100
4.2.2 Switch Screen Settings ......................................................................................... E117
4.2.3 Preset Screen Settings ..........................................................................................E125
4.2.4 Iris Screen Settings ...............................................................................................E131
4.2.5 Zoom Screen Settings ........................................................................................... E138
4.2.6 Focus Screen Settings .......................................................................................... E149
4.2.7 Info Screen Settings ..............................................................................................E151
4.2.8 Fol. Screen Settings .............................................................................................. E158
4.3 List of Settings ......................................................................................E160
5. Operation in Analog Mode E163
....................................................E164
5.1.1 Selecting Analog Mode ..........................................................................................E165
5.1.2 Top Screen ............................................................................................................E166
5.1.3 Specifying Auto Iris Gain .......................................................................................E167
5.1.4 Switching to Basic Mode .......................................................................................E168
................................................. E169
5.2.1 User Screen Settings ............................................................................................ E170
5.3 List of Settings ......................................................................................E175
Index End
E7
Introduction
GENERAL SAFETY INFORMATION
The safety warnings and cautions provided on the product or in this operation manual must be observed.
Failure to observe these warnings and cautions may result in injury or accident.
Read this operation manual carefully to familiarize yourself with its contents and ensure that you can operate the product
properly.
Also, store this manual in a safe place where it can easily be referenced whenever necessary.
This operation manual uses the following symbols and terms to identify hazards in order to prevent accidents.
Warning
This indicates a potentially hazardous situation which, if not heeded, may result in
death or serious injury to you or others. Be sure to heed all warning notices to en-
sure safe operation at all times.
Caution This indicates a potentially hazardous situation which, if not heeded, may result in a
minor injury to you or others, or damage to property.
Note This indicates cautions and recommendations for operation. It contains information
which, if not heeded, may result in this product failing to function properly.
These notices also contain useful information for operation.
E8
Introduction
HANDLING THE PRODUCT
Warning
1. Do not get this product wet or allow liquid inside. If water gets inside, stop using the product immediately. Continuing to
2. Do not stare at the sun or other bright objects through the lens. It may injure your eyes.
3. Be sure to hold the connector when disconnecting the cable. Pulling on the cable may sever or damage it and pose a
Caution
1. Be careful not to drop the product when carrying it. Dropping the product may cause injury.
2. Ensure that all mountings are securely tightened. If a mounting becomes loose, parts may fall off and cause injury.
3. Inspect mountings regularly (about every six months to one year) to ensure they are securely tightened. If a mounting
becomes loose, parts may fall off and cause injury.
4. When this product is used under a blazing sun, the inside of the unit may be heated to high temperature. When
customer’s side.
Note
1.
2.
cause the malfuction of the product.
3. In dusty environments, cover the lens mount when using, attaching or removing the lens. If dust enters inside, it may
cause the malfunction of the product.
4.
temporarily if condensation forms in the lens.
5. Before use in particular environments, such as places where chemical products are used, contact your Canon sales
representative or dealer.
E9
Introduction
DEALING WITH ABNORMALITIES
Warning
Should any of the abnormalities described below occur, immediately dismount the lens from the camera and contact
your Canon sales representative or dealer.
MAINTENANCE AND INSPECTION
Warning
Be sure to disconnect the cable and remove the lens from the camera before cleaning outside of the lens. Do not use
Note
wipe in a spiral pattern from the center of the lens. Be careful not to rub dust across the lens, which may scratch the
lens surface
2. Routine inspection about once a year is recommended, depending on the conditions and environment of use. Request
overhaul, if needed.
STORAGE
Caution
Always attach the lens cap, hood cap, dust cap or covers before storage. Storing the lens without the caps
Note
Immediately wipe off any moisture on the lens from misty or foggy environments, using a dry cloth. Seal the lens in
malfunction of the product.
E10
Introduction
TO THE CUSTOMER
1. Canon shall bear no responsibility for damage resulting from improper operation of this product by the customer.
2.
suitability for the customer’s purpose.
Moreover, Canon shall bear no responsibility for any damage, direct or incidental, that results from usage for the
customer’s purpose.
3.
4. notice.
5. For further information on repairs, maintenance, or adjustments not mentioned in this operation manual, contactyour
Canon sales representative or dealer.
6.
or your Canon sales representative.
The copyright for this manual is retained by Canon Inc.
Unauthorized copying or reproduction in whole or part is prohibited.
E11
Introduction
Manual Layout
Pages with instructions are organized as follows.
E94
4. Operation in Full Mode
Zoom
Iris
[ Z.M. ]
[ I-Gain ]
[Adj]
[]
MENU
1
A
Fr1P
[ Basic ]
[Trk]
OFF
[I-Tq]H
[]
MENU
MENU
1
RET
R
Fr1P
A 2
Norm
AM
Zoom
[ Z.M. ]
[]
MENU
MENU
1
RET
R
Fr1P
A 2
Norm
AM
Iris
4.1.15 Assigning Functions to the Seesaw
The zoom seesaw switch can be programmed to control either the {Zoom} or {Iris}.
Important
First, switch to the user for whom the settings apply.
(For instructions, see “4.1.3 Switching Users” or “4.2.1 User Screen Settings: Switching Users.”)
Press six times and once.
The previous or default function is highlighted.
Press .
The display starts blinking.
Press or .
Press left or right to switch the function to
{Zoom} or {Iris}.
Press .
The display changes from blinking to
highlighted, indicating confi rmation.
Options (D) Zoom Iris
Description Zoom operation Iris operation
(D): Default value
MENU
× 6
Zoom
or
1
2
3
4
Initial Top Screen
Note: Note on Iris Assignment
1. The seesaw switch will no
longer control zooming.
2. To control the iris with the
rocker switch, you must set
the iris mode to manual.
3. Press the Telephoto side to
open the iris, or press the
Wide end side to close it.
4. Zoom speed control
adjustments also apply to iris
control, and you can specify
the maximum iris speed. (See
“4.2.5 Zoom Screen Settings:
Specifying Maximum Zoom
Speed Control.)
Chapter title
Function title
Summary of function,
points to note
Operating procedure
Notes
Quick reference for
operating procedure
Page number
List of available
functions or options
E12
Introduction
Manual Conventions
The following conventions are used in this manual.
Convention Description Example
screen Names of screens are underlined. The Top screen is displayed.
[ ] Names of setting items are enclosed in square brackets. [Frame 1] is underlined.
{ } Names of options are enclosed in curly brackets. Select {FAST}.
E13
Introduction
Part Names
Part Names and Functions
Display
Activated when the Display switch is
pressed.
Turns off automatically if left idle for
two minutes.
DISPLAY
Display switch
Press to activate the display.
One press turns on the display, and
another turns it off.
Control keys
Used to confi gure all settings shown
on the display.
Identifi ed with fi ve key names,
depending on how this interface is
used.
(See the following table, “Using the
Control Keys.”)
Using the Control Keys
Key Operation Details Manual Convention
Set key
Press Pressed when { } is displayed, or when entering a
selection.
Right key
Move right
Can be used when { } is displayed.
Left key
Move left
Can be used when { } is displayed.
Up key
Move up
Can be used when { } is displayed.
Down key
Move down
Can be used when { } is displayed.
E14
Introduction
Basic Sequence of Operations
DISPLAY
[Trk]
OFF
Shtl
A 1
A 2
MENU
IG: 50
A
Fr1P
Fr1P
[I-Tq]H
[Adj]
DISPLAY
Press the Display switch.
Press the Display switch.
The display is now illuminated.
The display is turned off.
Changes are saved.
Use the control keys to complete settings.
1
2
3
4
Turn on the lens.
DISPLAY
MENU
[Trk]
ON
Shtl
A 1
A 2
IG: 50
A
Fr1P
Fr1P
[I-Tq]H
[Adj]
Important
For Reference: Display appearance when restoring original settings Restoring the Original
Settings
The original settings can be restored, in
the case of incorrect settings or if you have
tried some settings tentatively.
For details, see “Resetting Values”
in “3. Operation in Basic Mode” or
“4. Operation in Full Mode.”
Basic Mode
ResetAll
User
User:
B
y/n
Full Mode
ResetAll
User
User:
AllUser:
1
y/n
y/n
Note: For instructions on turning the lens on, refer
to the camera manual.
Note: The display turns off automatically after two
minutes if no control keys are pressed. (Auto
Off.) However, the display remains active as
long as the Fol. screen is shown. In this case,
it is only deactivated when you press the Dis-
play switch.
Note: Any changes to settings are saved even if the
display is automatically deactivated, just as
they are when it is switched off manually.
When the display is deactivated manually,
changes to settings are saved and the display
is turned off.
However, if the lens is turned off while the
display is on, changes to settings may not be
saved.
Screen Organization
1
INFORMATION DISPLAY
E16
1. Screen Organization
1. Screen Organization
Screens contain 22 setting items in Basic mode, 38 in Full mode, and 3 in Analog mode, with Basic and Full modes also
including a “follow” screen containing three setting items that have relative values. To access frequently used items on
the Top screen, press the Display switch. All settings can be confi gured from the Menu screen, which also includes
advanced settings. (See “Menu Screen” in “1. Screen Organization.”)
1.1 Top Screen
(For instructions on confi guring the settings, see “Confi guration from the Top Screen” in each mode.)
The Top screen contains 9 setting items in Basic mode, 15 in Full mode, and 3 in Analog mode.
Initial Top Screen in Basic Mode
[Trk]
OFF
Shtl
A 1
A 2
MENU
IG: 50
A
Fr1P
Fr1P
[I-Tq]H
[Adj]
Items not scrolled
Items displayed by scrolling
MENU
[ I-Tq ] H
A 1
Fr1P
IG: 50
[Trk]
OFF
[ Z.M. ]
A 2
Fr1P
Top Screen in Basic Mode
Of the 9 setting items in Basic mode, the 8 more common are
shown on the Top screen. The other 1 can be accessed by
pressing down to scroll down the screen.
1. Go to Menu screen
2. Auto iris gain settings
3. AUX switch assignment
4. Mechanical end auto-adjustment
5. AUX1 switch assignment
6. Zoom tracking ON/OFF
7. AUX2 switch assignment
8. Iris torque settings
9. Zoom curve mode settings
E17
1. Screen Organization
Initial Top Screen in Full Mode
[ I-Gain ]
[Adj]
[]
MENU
1
A
Fr1P
[ Basic ]
[Trk]
OFF
[I-Tq]H
Items not scrolled
Items displayed by scrolling
[]
MENU
1
Norm
AM
Zoom
RET
R
A 2
Fr1P
[ Z.M. ]
Top Screen in Full Mode
Of the 15 setting items in Full mode, the 8 most common are
shown on the Top screen. The other 6 can be accessed by
pressing down to scroll down the screen.
1. Go to Menu screen
2. Switch users
3. Switch to Basic mode
4. Mechanical end auto-adjustment
5. Iris gain settings
6. Zoom tracking ON/OFF
7. AUX switch assignment
8. Iris torque settings
9. AUX1 switch assignment
10. VTR switch assignment
11. AUX2 switch assignment
12. RET switch assignment
13. Zoom curve mode settings
14. Seesaw switch assignment
15. Iris A/M switch setting
Initial Top Screen in Analog Mode
MENU
IG: 50
[ Basic ]
Top Screen in Analog Mode
1. Go to Menu screen
2. Auto iris gain settings
3. Switch to Basic mode
E18
1. Screen Organization
1.2 Menu Screen
Menu screen.*1
Menu Screen in Basic Mode
Mode:
User
Basic
Access:
ResetAll
B
Unlock
1. User screen B
3. Preset screen
4. Iris screen
5.
[ ]
6. Focus screen
7.
8.
*1Menu screenMenu screen.
Top screenUser screen
Mode:
User
Basic
Access:
ResetAll
B
Unlock
Switch
B
AUX2:
A
A 1
AUX1:
A 2
Fr1P
AUX:
Fr1P
Shtl
Frame1:
Preset
Zoom
Frame2: Zoom
ZSpeed: 800
CurveMode
VR-Dem: ON
Zoom []
CurveMode
Focus []
Fol.
Iris:
Zoom:
Focus:
0000
1000
0000
B
Info
Encoder:
OFF
S/N
3D:
OFF
Menu Screen in Basic Mode
User screen
Zoom screen
Switch screen
Focus screen
Preset screen
Info screen
Iris screen
Fol. screen
Iris []
[ I-Gain ]
Torque: High
Comp:ON
E19
1. Screen Organization
Menu Screen in Full Mode
No. :
User
1
Name:
Mode:
Full
1
1. User screen
1
3. Preset screen
4. Iris screen
5.
[ ]
6. Focus screen
7.
8.
*1Menu screenMenu screen.
Top screenUser screen
Menu Screen in Full Mode
User screen
Zoom screen
Switch screen
Focus screen
Preset screen
Info screen
Iris screen
Fol. screen
No. :
User
1
Name:
Mode:
Full
1
Switch
1
AUX2:
A
A 1
AUX1:
A 2
Fr1P
AUX:
Fr1P
Shtl
Frame1:
Preset
Zoom
Frame2: Zoom
ZSpeed: 800
Iris []
[ I-Gain ]
Torque: High
Comp:ON
Tracking:
CurveMode
OFF
Movement
Zoom []
CurveMode
Focus []
Fol.
Iris:
Zoom:
Focus:
0000
1000
0000
1
Info
Encoder:
OFF
S/N
3D:
OFF
E20
1. Screen Organization
Menu Screen in Analog Mode
Menu Screen in Analog Mode
In Analog mode, 2 setting items are presented as the User screen.
Icon of selected screen is
highlighted.
Mode:
User
Analog
Access:
A
Unlock
1. User screen
*1: There is no single Menu screen. Instead, screens accessed by selecting [MENU] are collectively referred to as the Menu
screen.
To access this screen, select [MENU] on the Top screen and press the Set key. The User screen is now displayed.
User screen
Mode:
User
Analog
Access:
A
Unlock
Mode Selection
2
INFORMATION DISPLAY
E22
2. Mode Selection
2. Mode Selection
2.1 Modes
The following 3 modes are available. Choose a mode that suits your purpose or preference.
1. Basic Mode: Restricted settings and information. Recommended for users who do not require sophisticated
settings. This is the default mode.
2. Full Mode: All settings and information are available.
3. Analog Mode: Used when no digital functions are needed.
For details, see “3. Operation in Basic Mode,” “4. Operation in Full Mode,” or “5. Operation in Analog Mode.”
Table of contents
Other Canon Camera Accessories manuals
Canon
Canon TIMER REMOTE CONTROLLER TC-80N3 User manual
Canon
Canon BG-E21 User manual
Canon
Canon HG-100TBR Assembly instructions
Canon
Canon BU-47H 1AM User manual
Canon
Canon BU-47H 1AM User manual
Canon
Canon EXTENDER EF 2.0x Instruction Manual
Canon
Canon REMOTE SWITCH RS-80N3 Instruction Manual
Canon
Canon Extender EF 1.4X III User manual
Canon
Canon XF User manual
Canon
Canon SPEEDLITE 200E Instruction Manual
Canon
Canon EF 600mm 1:4.0 L USM Instruction Manual
Canon
Canon Macro Twin Light MT-26EX-RT Assembly instructions
Canon
Canon EF100mm f/2 USM User manual
Canon
Canon TIMER REMOTE CONTROLLER TC-80N3 User manual
Canon
Canon Camera Accessory Kit 5 User manual
Canon
Canon WFT-E7 User manual
Canon
Canon Speedlite Transmitter ST-E2 User manual
Canon
Canon XF705 User manual
Canon
Canon Plenum SR30-P-VB User manual
Canon
Canon DU-82 User manual
Popular Camera Accessories manuals by other brands
Samsara
Samsara ACC-SC-MNT-J1 installation guide
Contardi
Contardi Muse Small installation instructions
Moog Videolarm
Moog Videolarm POD8C Product instructions
Puls
Puls UZK24.071 instruction manual
Big Game Treestands
Big Game Treestands THE DELTA instruction manual
Turbo Energy
Turbo Energy Lithium Series instruction manual