CANOPY 27 RD Instruction Manual

PARTS LIST
1 Radio Mount 
1 Feed Tube
1 Antenna Reflector
1 AZ/EL Mount
1 Mast
2 Hose Clamps
2 Carriage Bolt .25 x 20
1 Hex Bolt .25-20 x 1.5"
3 Flange Nut .25-20
3 Flat Washers .25-20
1 Spacer
1 Carriage Bolt #10 x 1.25"
1 #10 Hex Nut
2 U Bolts 5/16
2 V-Bracket
4 Star Nut
1 Canopy Module Radio
QTY DESCRIPTION  BACKHAUL MODULE  SUBSCRIBER MODULE REFLECTOR (ONLY)
    with REFLECTOR (BHRF) with REFLECTOR  (27RD)
RADIO MOUNT
CANOPY
MODULE
RADIO
HOSE CLAMP
(2 PLACES)
AZ/EL MOUNT
MAST U BOLT
(2 PLACES)
V-BRACKET
(2 PLACES)
SPACER
CARRIAGE BOLT
#10 x 1.25"
HEX BOLT
.25-20 x1.5"
FEED
TUBE
FLANGE NUT
.25-20
CARRIAGE BOLT
.25 X 20
(2 PLACES)
#10 HEX
NUT
FLAT WASHER
.25-20
FLANGE NUT
.25-20
(3 PLACES)
FLAT WASHER
.25-20
(3 PLACES)
STAR NUT
(4 PLACES)
ANTENNA
REFLECTOR
http://www.motorola.com/canopy
Sales Support: 866-515-5825
Technical Support: 888-605-2552 ([phone])
REFLECTOR ASSEMBLY and INSTALLATION
27 RD REFLECTOR
Tools Needed:  7/16 inch wrench or adjustable wrench
    Flat blade screwdriver or 5/16 inch socket for hose clamps and ground screw
    1/2 inch wrench for U-Bolts - Backhaul only
    3/8" wrench for #10 nut
Tighten Hose
Clamps securely
so the Radio is
snug to the mount
with no gaps at
the lower support
rib.
4
Loosen and open hose clamps. Slide clamps through the two
openings in the Radio above and below the mount as shown in
this illustration. Close hose clamps attaching radio to mount.
3
Slide Radio into mount as shown.
2
RADIO MOUNT
RADIO
Place Antenna Reflector on flat surface or table.
Attach AZ/EL Mount to Reflector using Carriage Bolts,
Flat Washers, and Flange Nuts. Tighten nuts securely.
1
RADIO
RADIO
MOUNT
HOSE
CLAMPS
CARRIAGE
BOLT
FLAT WASHER
FLANGE NUT
REFLECTOR
AZ/EL
MOUNT
HOSE
CLAMP
9/04 ECN9000000 8000973-01
RADIO
MOUNT
HOSE CLAMP
ADJUSTMENT
SCREW
(FACING
RADIO)

Assemble the Feed Tube to the Reflector as
shown with 1/4" Flange Nut, .81" Spacer,
Flat Washer and 1-1/2" Hex Bolt. Tighten
hardware securely.
6
1/4" HEX
FLANGE NUT
SPACER
FLAT
WASHER
1-1/2"
HEX BOLT
7
Slide assembled
radio and mount
into feed tube as
shown.
Secure Radio Mount to Feed Tube with #10 x 1-1/4"
Carriage Bolt and #10 Nut. Tighten Nut to snug the
bottom of the tube up to the Mount.
#10 NUT
#10 x 1-1/4"
CARRIAGE
BOLT
8
9Install Mast on tower or building. For Backhaul,use provided U-Bolts. For Subscriber Module, use locally
approved fasteners (lag bolts, screws, etc.) depending on installation. Adjust Mast to be vertical and plumb.
Tighten all hardware securely. Connect Ground Screw to Earth Ground using heavy guage (10AWG) copper
wire. Refer to local or national electrical regulations for exact specifications.
BACKHAUL MOUNT SUBSCRIBER MOUNT
VERTICAL & PLUMB
LOCALLY APPROVED FASTENERS
U BOLT STAR
NUT
V-BRACKET
MAST
12
E
L
E
V
A
T
I
O
N
-20
-10
0
10
20
The Elevation is set by rotating the Reflector vertically while the Elevation Adjustment Hardware is loose.
An elevation scale is located on the side of the AZ/EL Mount. As the Reflector is adjusted, the elevation
scale depicts the elevation angle. Once the elevation is determined, tighten BOTH Elevation Ajustment Nuts
to secure the required angle.
E
L
E
V
A
T
I
O
N
-20
-10
0
10
20
ELEVATION
ADJUSTMENT
NUT (ONE ON
EACH SIDE)
VERTICAL & PLUMB
UP TO
3.25" O.D.
PIPE (8.0cm O.D.)
10 AWG
GROUND
WIRE
GREEN
GROUND
SCREW
ALTERNATE
GROUND
SCREW HOLE
MAST
AZ/EL MOUNT
AZ/EL
MOUNT
CLAMP
Loosen bolts on AZ/EL Mount Clamp. Slide AZ/EL
Mount with preassembed Reflector over mast.
Loosely tighten AZ/EL Mount Clamp.
10 11To adjust azimuth, move Reflector from side to side
while AZ/EL Clamp Hardware is loose. Once azimuth
is determined, tighten (2) AZ/EL Clamp Nuts securely.
AZ/EL
CLAMP
NUTS
REFLECTOR
ELEVATION
Read indicated elevation at this
edge of plate. The Beam from
the Reflector will be horizontal
when the Mast is vertical and
the plate is set at 4.5 degrees
up-elevation as shown.
Place Feed Tube on a solid surface or
table. The Reflector end of the Feed Tube
has a large hole on the bottom side. Align
bolt holes and press Reflector Socket
completely onto Feed Tube as shown.
5
FEED TUBE
ANTENNA
REFLECTOR